Guide Roller Height Adjustment - Sony SLV-L45AR Service Manual

QQ
3 7 63 1515 0

4-3-3. GUIDE ROLLER HEIGHT ADJUSTMENT

(See Figs. 4-3-3 and 4-3-4)
1) Play the Alignment Tape (NTSC: KRV-52NE, PAL: KRV-
52PL) and check that the envelope waveform is at its
maximum at the tracking centre. Then, after loosening
the S guide roller and the T guide roller by rotating them
anticlockwise, tighten them in turn until the envelope
waveform becomes flat. If the envelope waveform is not
at its maximum at the tracking centre, refer to section 4-
3-4 and carry out a rough adjustment of the horizontal
position of the audio R/P head (ACE head) before
adjusting the guide rollers.
2) Adjust the S guide roller.
1 Press the tracking button (Channel – ), and check
whether, when the envelope waveform has reached
50% of its maximum, the front half of the envelope
waveform is flat. If not, fine-tune the S guide roller as
follows.
a. If the front half of the envelope waveform is as shown
in Fig. 4-3-4 (a), this means that you have pressed the
S guide roller too far. Therefore, loosen it slightly, and
when it is in the state shown in Fig. 4-3-4 (b), tighten it
again, stopping when the envelope waveform is flat.
b. If the front half of the envelope waveform is as shown
in Fig. 4-3-4 (b), this means you have not pressed the
S guide roller far enough. Therefore, tighten it slightly,
stopping when the envelope waveform becomes flat.
c. If the front half of the envelope waveform is as shown
in Fig. 4-3-4 (c), it may happen that when you tighten
the S guide roller, the wrapper waveform does not
disappear, but sinks into the flat part, as shown in Fig.
TE
L 13942296513
4-3-4 (d). If this happens, the status shown in Fig. 4-3-
4 (c) is normal, so loosen the S guide roller, then
tighten it again until the envelope waveform is as
shown in Fig. 4-3-4 (c).
2 Check that at the tracking centre, the output of the
front half of the envelope waveform is not less than
80% of the maximum.
3 Rotate the S guide roller 20° anticlockwise.
3) AdjusttheTguide roller.
1 press the tracking button (channel – ) and check
whether, when the envelope waveform is 50% of
maximum, the back half of the envelope waveform is
flat. If not, loosen the T guide roller slightly, then
tighten it gradually until the back half of the envelope
waveform becomes flat.
2 Check that the output for the back half of the envelope
waveform is at its maximum at the tracking centre.
4) Check that the envelope waveform does not fluctuate
when you switch from F-SEARCH to PLAY or from R-
SEARCH to PLAY. If it does fluctuate, repeat steps 3)
and 4).
www
.
http://www.xiaoyu163.com
x ao u163
y
i
http://www.xiaoyu163.com
2 9
8
Normal
Eccentric screwdriver
(J-6082-044-A)
Do not touch
the fixed
screw
Q Q
3 6 7 1 3 1 5
If the envelope waveform
is at maximum at the
tracking centre, adjust to
flat.
(a) S guide roller
pressed too far
(c) Normal status for
wrapper waveform
co
.
5-27
9 4 2 8
Pressed Not pressed
too far far enough
T guide roller
S guide roller
The tape should not pass along
the cylinder lead surface
0 5 8 2 9 9 4 2 8
In normal status, the waveform
will be flat even when the
envelope waveform is reduced
to 50%.
100%
(b) S guide roller not
pressed far enough
50%
(d) S guide roller
pressed too far
50%
m
9 9
Fig. 4-3-3
9 9
50%
50%
50%
Fig. 4-3-4