Table of Contents
Advertisement
Quick Links
Safety Information.......................................................................................................... 2
What is the DS-1000 series digital storage oscilloscope .......................................... 5
Packing list....................................................................................................................... 6
Specifications .................................................................................................................. 7
System Requirements .................................................................................................... 9
Installation Procedures ..................................................................................................11
Quick Start: (Calibration)..............................................................................................15
Screen ................................................................................................................................17
Channel Switch Button..................................................................................................17
VOLTS/DIV Knob ..........................................................................................................18
SEC/DIV Knob ................................................................................................................18
Main Function Button ....................................................................................................19
Sub-Function Button ......................................................................................................19
RUN/STOP Button .........................................................................................................19
Force Trigger ....................................................................................................................19
AUTOSET ........................................................................................................................19
Set to 50% Button ............................................................................................................20
Hard Copy Button...........................................................................................................20
Panel Switch Button .......................................................................................................21
Skin Panel ........................................................................................................................22
Threshold .........................................................................................................................22
Channel.............................................................................................................................22
Scroll Bar ..........................................................................................................................22
Panel Sizing Knob ..........................................................................................................22
Trigger...............................................................................................................................22
Trigger...............................................................................................................................24
Display..............................................................................................................................25
Cursor................................................................................................................................26
Measurement ...................................................................................................................27
Utility ................................................................................................................................27
Save/Recall .......................................................................................................................32
Acquire..............................................................................................................................33
Chapter 5: How to stack more than one DSO
How to stack more than one DSO ...............................................................................35
Appendix ..........................................................................................................................37
Table of Contents
1
─
─
Acute
Advertisement
Table of Contents
Related Manuals for Acute DS-1000
Summary of Contents for Acute DS-1000
-
Page 1: Table Of Contents
Acute Table of Contents Safety Information Safety Information......................2 Chapter 1: Introduction What is the DS-1000 series digital storage oscilloscope .......... 5 Packing list........................6 Specifications ........................7 System Requirements ....................9 Chapter 2: Installation Installation Procedures ....................11 Quick Start: (Calibration)....................15 Chapter 3: Operations Screen ..........................17... -
Page 2: Safety Information
Use USB2.0 power only The DS-1000 is and should be powered by the PC’s USB2.0 port. Use only the DS-1000 USB cable within the DS-1000 soft case to connect to the PC’s USB2.0 port. - Page 3 Acute If there is smoke, abnormal smell or abnormal sound, unplug the USB cable from the DS-1000 immediately. Do not modify or operate the DS-1000 if there is any suspected damage; have it inspected by qualified service personnel. WARNING Connect the Probe Properly The probe ground lead is at ground potential.
-
Page 4: Chapter 1: Introduction
Chapter 1 Introduction ─ ─... -
Page 5: What Is The Ds-1000 Series Digital Storage Oscilloscope
Acute What is the DS-1000 series digital storage oscilloscope? The DS-1000 series is a PC-based, pocket-sized digital storage oscilloscope (DSO) designed and manufactured by Acute Technology Inc. It has three models: DS-1002, DS-1102, and DS-1202 with the same functionality as its stand-alone peers. -
Page 6: Packing List
Introduction Packing list Item DS-1000 Pocket-DSO mainframe 250MHz probes (1x/10x) Probe accessory pack USB A-B cable Installation CD Quick Manual DSO soft case DS-1002 provides 2 100MHz probes (1x/10x). ─ ─... -
Page 7: Specifications
Acute Specifications DS-1000 Specifications Acquisition Mode Real-time sampling, Equivalent sampling, Roll mode, Average, Envelope Input Input Coupling AC, DC, GND Input Impedance 1M ±1% // 21pF±5% 42Vpk (DC + AC peak) Max. Input Voltage Vertical Channel 2 (DS-1202 allows stacking of up to max. 6 channels.) - Page 8 Introduction Measurement Vpp, Vmax, Vmin, Vamp, Vtop, Vbase, Vupper, Vmiddle, Vlower, Vmean, Vrms, Positive overshoot, Negative overshoot, Period, Frequency, Pulse width Cursor Time difference, Voltage difference Math Add, Sub, Multiplication, Division Rectangular (Vertical scale: dbV RMS, Linear RMS) Export Data WORD, EXCEL, CSV, TEXT, HTML, Clipboard, Hardcopy, Preview Trigger Input/Output EXT-TRIG Input Limitation...
-
Page 9: System Requirements
Acute System Requirements ♦ Pentium 1.2GHz (or higher compatibles), Pentium 2.0GHz CPU (or higher) recommended. ♦ PC memory 64M bytes of RAM minimum. ♦ At least 32M bytes of available hard disk space. ♦ CD-ROM drive (for installation). ♦ Display specification, 640x480 VGA (or higher), 800x600 or 1024x768 recommended. -
Page 10: Chapter 2: Installation
Chapter 2 Installation ─ ─... -
Page 11: Installation Procedures
1. Insert installation CD, if you see a hardware wizard, please cancel it. Then connect the USB cable to the DS-1000 and the PC or notebook computer. 2. Windows will find a USB device automatically and enter the hardware wizard (Figure 1). - Page 12 DS-1000 USB interface is installed. If an exclamation or question mark appears on the ““Acute USB 2.0 Interface”, that indicates the device is in a problem state. Please visit the FAQ page of our web site at http://www.acute.com.tw or email us at service@acute.com.tw.
- Page 13 Figure 2 3. Choose “Install the software automatically (Recommended)” to find the proper driver automatically (Figure 2). Click “Next”. 4. Windows will search for a proper driver for the DS-1000 (Figure 3); this could take a while. Figure 3 Figure 4 5.
-
Page 14: Application Installation
Desktop or in the Programs group. You may double click either icon to start the DSO AP. 7. If you enter “DEMO Mode” when you launch the DS-1000 AP, this means that some problem has occurred. Please contact your dealer or email us at service@acute.com.tw. -
Page 15: Quick Start: (Calibration)
Acute Quick Start: (Calibration) 1. Connect the two probes to the DS-1000’s Channel 1 and Channel 2 BNC connectors. 2. Switch the Probe to “x10”. 3. Connect the two probe ground leads to the DS-1000’s ground terminal. 4. Connect the two probe tips to the DS-1000’s “Probe Comp. (3.3V)” terminal. -
Page 16: Chapter 3: Operations
Chapter 3 Operations ─ ─... -
Page 17: Screen
Acute Screen Function Information Shortcut Button CH1 Waveform Panel Switch Button Sub-Function Button CH2 Waveform Channel Select. Panel Sizing Waveform Horz. Adj. Scroll Bar Waveform Vert. Adj. Main Function Button Channel Switch Button There are 6 channels, CH1, CH2…, CH6 on the upper right corner of the panel as shown above. -
Page 18: Volts/Div Knob
Operations VOLTS/DIV Knob The VOLTS/DIV knob is used to change the vertical voltage scale. On the screen’s lower-left corner, a voltage scale (for each division is) displayed. There are 8 vertical divisions on the screen. For example, if the corner displays “CH1 2.00V”, this means that the voltage scale is 2 Volts for each vertical division and the voltage distance from top to bottom of all 8 divisions on the screen is 16 Volts. -
Page 19: Main Function Button
Save/Recall, and Acquire under the Full mode screen. When you disconnect the DS-1000 from your PC and launch the DSO AP, the program automatically changes to Demo mode and the Acquire button becomes the Demo button. If you still want... -
Page 20: Set To 50% Button
Voltage, Time, and Trigger parameters of the CH1 signal(s) will be the benchmark parameters used for the “AUTOSET” function. Set to 50% Button Pushing the “Set to 50%” button will cause the DS-1000 to fine tune the trigger level to the mean voltage of the trigger signal. Hard Copy Button The “Hard Copy”... -
Page 21: Panel Switch Button
Acute Panel Switch Button Panel Switch button There are 2 display modes for the DS-1000 AP panel; one is the full panel mode, with function buttons on the right of the panel. The other is the skin panel mode, with function buttons hidden. -
Page 22: Skin Panel
Operations Skin Panel In the skin panel, the main function buttons are hidden; but the main functions and sub functions can be found in the pull-down menu on the upper right panel. Threshold The trigger Threshold is represented by an arrow symbol on the right side of the panel. -
Page 23: Chapter 4: Functionality
Acute Chapter 4 Functionality ─ ─... -
Page 24: Trigger
The Trigger system has 3 modes: Auto, Normal, and Single Shot. Under “Auto”, when the SEC/DIV setting is 200ms or greater, DS-1000 automatically turns to “Roll Mode”. Memory Depth Under single shot mode, you can adjust memory depth to 2000、4000、8000、16000、... -
Page 25: Display
Acute right side sub-function button, a “Video Scan Line Setting” dialog box (above) will appear. You can choose Video Type, Horizontal Frequency, and number of scan line. Video type can be NTSC, PAL or SECAM. Horizontal frequency can be adjusted according to the signal under test. The “Identify” button on the lower left corner of the “Video Scan Line Setting”... -
Page 26: Cursor
Functionality 、A-B、, 、B-A、, and 、X-Y、; 、A+B、, 、A-B、 or 、B-A、 operations of add, or subtract between values of CH1 and CH2. 、X-Y、 is “Lissajous Pattern” with CH1 as time axis and CH2 as voltage axis. Cursor There are two cursors: Time (two vertical lines) and Voltage (two horizontal lines). The two vertical (or horizontal) lines are used measure relative time or voltage of points on the signal under test. -
Page 27: Measurement
Waveform area to add or delete measurement values. Utility A. Languages English and Traditional Chinese are used in the DS-1000 AP and can be switched anytime to your preference. Factory The DS-1000 will automatically change its original setup values through the calibration process. - Page 28 Functionality D. Logger “Logger” records (saves) waveform data in your computer’s hard disk. “Logger” has three sub functions: Interval, Every Trigger, and Every Sampling. 1. Interval (Auto Mode only) “Interval” saves waveform data in an interval (in tens of milli-second increments that can be defined in edit box and Only works in “Auto”...
- Page 29 Import data “Import data” imports waveform data, or a setup file (*.set) described in “Export data”. The information disclosure sub-function can capture the DS-1000 waveform information and change it to a different format. For example: Print out, preview, Word, Excel, text, or clipboard, etc.
- Page 30 H. Waveform Waveform has four modes: “Normal”, “Intensity”, “Bezier”, and “Dot”. “Normal” displays the exact waveform captured by DS-1000 in real time. “Intensity” copies the Intensity characters on the screen and retains the old waveform on the screen until the new waveform appears; then the old waveform fades out.
- Page 31 Hot Key Setting “Hot Key Setting” is a very easy-to-use function, especially for non-engineering users, such as production line operators, who need to operate DS-1000 for production purposes. In the “Hot-Key Setting” dialogue box, you may create “Hot Key” with function(s) or sub-function(s) in a “define” list, or you can delete the “Hot Key”...
-
Page 32: Save/Recall
Functionality Save/Recall Save/Recall saves or recalls waveforms for comparison purposes. There are four reference waveforms that can be used (save/recall). Enter “Save/Recall” in the dialog box and save the waveform to file as in the dialog box (on the right), then use the saved file waveform as the reference. -
Page 33: Acquire
“ETS” records high-frequency repetitive waveform signals and merges them to display a finely defined waveform. However, when the SEC/DIV setting is > 500ns, the DS-1000 will automatically switch to “Sample” mode. “Average” mode is used to average the noise of signals. - Page 34 Chapter 5 How to stack more than one DSO ─ ─...
-
Page 35: How To Stack More Than One Dso
Also, a third device can be stacked in the same manner. If 3 devices are stacked, the DS-1000 AP shows the following dialog box along with the 3 devices’ respective serial numbers. The Master device is associated with “CH1, CH2”... -
Page 36: Chapter 6: Miscellaneous
Chapter 6 Miscellaneous ─ ─... -
Page 37: Appendix
Acute APPENDIX Auto mode The waveform will be refreshed either when trigger occurs or after time-out. Normal mode The waveform will be refreshed every time trigger occurs. Single-Shot mode The waveform will be refreshed the first time trigger occurs. Roll mode The waveform will not be refreshed but will be displayed in roll mode if SEC/DIV >... - Page 38 Miscellaneous Memo ─ ─...
- Page 39 Acute Memo ─ ─...
- Page 40 Miscellaneous Memo ─ ─...
Need help?
Do you have a question about the DS-1000 and is the answer not in the manual?
Questions and answers