Advertisement
Quick Links
T
Y
hank
ou
Thank you for purchasing a VP4150 RemotePoint Navigator.
We know you had other choices and we appreciate that you
chose Interlink Electronics by SMK-Link for your wireless
needs. So that we may better serve you in the future, please
register online at
www.smklink.com/register.
W
arranTY
Two Year, Limited Warranty
S
upporT
SMK-Link Electronics Corporation
3601-B Calle Tecate
Camarillo, CA 93012
TEL: (888) 696-3500
FAX: (805) 987-6665
FCC Certification
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions: (1) This device may not cause harmful
interference, and (2) This device must accept any interference received, including interference
that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a CLASS B digital
device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable
protection against harmful interference when the equipment is operated in a residential
installation. This equipment generates, uses, can radiate radio frequency energy and if not
installed and used in accordance with the instruction guide, may cause harmful interference to
radio communications. However, there is no guarantee that this radio interference will not occur
in a particular installation. If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment on and off, the user is encouraged
to try to correct the interference by one or more of the following measures:
Re-orient or relocate the receiving antenna.
Increase the separation between the equipment and the receiver.
Consult the dealer or an experienced Radio-TV technician for help.
Notice: Any changes or modifications not expressly approved by the party responsible for
compliance could void the user's authority to operate the equipment. Extension cables are not
recommended, if used, they must be shielded in order to comply with the emission limits.
IC Certification
The term "IC" before the certification/registration number only signifies that the Industry Canada
technical specifications were met.
Declaration of conformity
Manufacturer:
SMK-Link Electronics Corporation
3601-B Calle Tecate
Camarillo, CA 93012
Hereby, SMK-Link. declares that the VP4150 is in compliance with the essential requirements
and other relevant provisions of Directive 1999/5/EC.
EMC/EMI/Safety Standards:
EN 300 440-2 V1.1.1 (2001-09)
EN 301 489-1 V1.4.1 (2002-08)
EN 301 489-3 V1.4.1 (2002-08)
EN 60825-1 (1994, A11:1996, A2:2001)
Users Manual
VP4150/VP4160
LASER RADIATION – DO NOT
STARE INTO BEAM
WAVE LENGTH: 635nm
MAX OUTPUT: <1mW
CLASS II LASER PRODUCT
Advertisement
Subscribe to Our Youtube Channel
Summary of Contents for Interlink electronics VP4150
-
Page 1: Users Manual
3601-B Calle Tecate 3601-B Calle Tecate Camarillo, CA 93012 Camarillo, CA 93012 Hereby, SMK-Link. declares that the VP4150 is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC. EMC/EMI/Safety Standards: TEL: (888) 696-3500 EN 300 440-2 V1.1.1 (2001-09) LASER RADIATION –... - Page 2 irST eTTing up The emoTe oinT avigaTor emoTe oinT avigaTor onTrolS Your presentation remote comes set up from the factory. In most situations no adjust- Install batteries in the battery compartment. ments are needed; however, if you have many remotes or another device which is causing interference, complete these steps to avoid interference. Activate Laser raining The eCeiver With the computer turned on, plug the receiver into a free USB Previous Slide Next Slide To train the receiver to accept the digital code from the remote, remove the USB port. (If the computer displays a “ Found New Hardware” dialog receiver from the USB port and reconnect it after a few seconds. box, click Next until the driver is installed.) Blank Presentation Press and hold the Next button (the right arrow) for 10 seconds until the red light on the remote turns back on. The LED on the receiver should turn from flashing Initialize the RemotePoint Navigator by pressing the Blank green to solid green then back to flashing green. button within 10 minutes of connecting the receiver. hanging hannelS hanging The lank Remove the battery from the remote. In certain languages a different key code may be needed to blank the screen during a Replace the battery and hold down the Previous button (the left arrow) for 10 presentation. Three key codes are provided for the various presentation programs.
Need help?
Do you have a question about the VP4150 and is the answer not in the manual?
Questions and answers