Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Summary of Contents for GE Security SP-PoE
- Page 1 Security SP-PoE Splitter User Manual P/N 1069176-EN • REV 1.01 • ISS 21MAR10...
- Page 2 Copyright © 2010 GE Security, Inc. This document may not be copied in whole or in part or otherwise reproduced without prior written consent from GE Security, Inc., except where specifically permitted under US and international copyright law. Disclaimer The information in this document is subject to change without notice.
- Page 3 Regulatory N4131 information Manufacturer GE Security, Inc. HQ and regulatory responsibility: GE Security, Inc., 8985 Town Center Parkway, Bradenton, FL 34202, USA EU authorized manufacturing representative: GE Security B.V., Kelvinstraat 7, 6003 DH Weert, The Netherlands European Union directives 2002/96/EC (WEEE directive):...
-
Page 4: Table Of Contents
Content Chapter 1 Overview 1 Package Contents 2 Introduction 2 Product Overview 3 Chapter 2 Hardware Installation 7 Before Installation 7 Installation 9 SP-PoE Splitter User Manual... -
Page 5: Overview
Chapter 1 Overview The GE Security SP-PoE is an IEEE 802.3af Power over Ethernet device that splits the 48VDC power input over an Ethernet cable into separate 5V and 12V DC power outputs. SP-PoE Splitter User Manual... -
Page 6: Package Contents
SP-PoE Splitter module. Introduction The GE Security SP-PoE is an IEEE 802.3af Power over Ethernet device that splits the 48VDC power input over an Ethernet cable into separate 5V and 12V DC power outputs. The SP-PoE works with IEEE 802.3af power source equipment (PSE). -
Page 7: Product Overview
SFP1000LX-10Km provides distance up to 10km over 9/125µm single mode fiber cable Product Overview Figure 1 shows the left and right side panels of the SP-PoE Splitter Figure 1: Left and right side panels of the SP-PoE LED Indicators Color... -
Page 8: Product Specifications
Number of Device can be powered Ethernet Cable TIA/EIA-568, Category 5/5e cable Installation Standalone or Wall mountable Material Plastic Standards Conformance Standard Compliance IEEE 802.3 10Base-T Ethernet IEEE 802.3u 10/100Base-TX Fast Ethernet IEEE 802.3af Power over Ethernet PD SP-PoE Splitter User Manual... - Page 9 DIP switch 5V: 5VDC, 2.0A max DIP switch 12V: 12VDC, 1.0A max NOTE: This product is intended to be supplied by a UL Listed Direct Plug-In Power Unit marked "Class 2" or "LPS" and output rated 48 VDC, 3 Amp minimum. SP-PoE Splitter User Manual...
- Page 10 Chapter 1: Overview SP-PoE Splitter User Manual...
-
Page 11: Hardware Installation
SP-PoE provides DC power for this Ethernet Device conveniently and easily. The SP-PoE separates the power out and provides two kind of DC power output through its DIP switch and its voltage and current shown as below: •... - Page 12 Chapter 2: Hardware Installation Figure 2: 5V/12V DC out DIP switch The default value is set on 5V. MS-POE and SP-PoE units can be installed in pairs. However, use of third-party device is allowed if the device complied with IEEE 802.3af standard.
-
Page 13: Installation
The SP-PoE only accepts IEEE 802.3af equipment. Other in-line power devices may cause the SP-PoE to malfunction. Connect the UTP cable in the package from "Ethernet" of SP-PoE to the RJ-45 port of remote device. Connect proper DC plug from "DC OUT" of SP-PoE to remote device. - Page 14 Chapter 2: Hardware Installation Connect with other802.3af devices The SP-PoE also provides an alternative way to connect to non IEEE 802.3af devices and to connect with an IEEE 802.3af in-line power device like a Power over Ethernet Switch. See the figure below.
Need help?
Do you have a question about the SP-PoE and is the answer not in the manual?
Questions and answers