Basic Use; Functions; Charging The Headset; Manually Pairing The Headset - Energizer ENG-BT1001 Quick Start Manual

Functions

Indicator
Light
Volume up/down

Basic use:

1. To make a call, use your phone in the normal way
when the headset is connected to your phone.
2. To answer a call, press and release the Call Button
or press the answer key on your mobile phone.
3. To end a call, press and release the Call Button or
press the answer key on your mobile phone.
4. To redial the last number, press and hold the
volume up button for 3 seconds.
Note: Not all phones support this feature.
5. To reject an incoming call, press and hold the Call
Button for 3 seconds until you hear a short beep.
6. To adjust the volume, press volume up or volume
down to increase or decrease the volume level.
7. To mute the microphone (place the call on hold),
press and hold the volume down button for 3
seconds. You will hear a beep.
8. To unmute the microphone (take the call off
hold), press and hold the volume down button
for 3 seconds. You will hear a beep.

Charging the headset:

1. Connect the charging pin of the USB cable to the
charging socket of the headset.
2. Connect the other end of the USB cable to either
the AC Charger (and plug into a wall A/C outlet)
or the computer's USB port.
The red LED indicator light turns on while the
headset is charging.
The red LED indicator light shuts off when the
headset is fully charged (approximately 2-3
hours).
Note: When the battery is running low, the red
LED indicator light starts to flash along with a
warning beep.
Note: Unplug the charger from the wall outlet
and the device when not in use. Do not leave a
fully charged battery connected to a charger,
since overcharging may shorten its lifetime.
Switching the headset on/o :
1.
To switch on, set the Power Switch to the ON
position (green). The indicator light will flash
Charging Socket
blue.
2. To switch off, set the Power Switch to the OFF
position (red). The indicator light will flash red
Call Button
before the headset shuts off.
Answer/end a call
Pairing for the rst time:
Power Switch
Power ON/OFF
(Green=ON, Red=OFF)
1. Ensure the Bluetooth headset is within 3 feet of
Microphone
your mobile phone or Bluetooth enabled device.
2. Set the Power Switch to the ON position.
3. When the indicator light flashes red and blue
alternately, you can connect the headset to your
Bluetooth enabled device.
Note: If the first time pairing was unsuccessful or
for future paring, manually pair the headset to
your Bluetooth enabled device.

Manually pairing the headset:

1.
Ensure the Bluetooth headset is within 3 feet of
your mobile phone or Bluetooth enabled device.
2. Set the Power Switch to the ON position.
3. Press and hold the Call Button until the indicator
light flashes red and blue alternately. The
blinking red and blue lights indicate that the
headset is in pairing mode .
Note: To enter pairing mode at any time, you
must press and HOLD the Call button down for
approximately 8 seconds.
4. Set your mobile phone to search for Bluetooth
devices. When your mobile phone finds the
headset, confirm by selecting ENGBT1001 from
the list.
5. Enter the passcode "0000" when prompted by the
phone. Select "Pair" to complete the pairing
process.
Note: If the Bluetooth version of your Bluetooth
mobile phone is V2.1, you will not need to enter a
passcode during above pairing process.
6. If the pairing is successful, the headset's indicator
light turns to standby mode and flashes once
every three seconds.
Energizer and other marks, including graphics, are trademarks of Energizer and are
used under license. All other trademarks, brand names or product names are the
property of their respective owners and are not affiliated with Energizer or Premier
Accessory Group, LLC.