Advertisement

Firmware Version: 1.xx
EN
USER INSTRUCTIONS AND SAFETY
v.04

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the B1 and is the answer not in the manual?

Questions and answers

Zaurbek Khetagurov
March 22, 2025

I have paired the n-com B1 with my android but can't here the voice in navigation mode.

1 comments:
Mr. Anderson
March 22, 2025

If your N-Com B1 is paired with your Android device but you can't hear voice navigation, possible reasons include:

1. Interruption by Other Connections: The B1 system temporarily disables intercom communication when receiving GPS instructions. If another Bluetooth connection (such as a phone call) is active, GPS audio may not be transmitted.

2. Incorrect Pairing: Ensure the GPS navigation audio is correctly routed through Bluetooth. If your Android device is paired for calls but not for media audio, navigation instructions may not be transmitted.

3. GPS Settings: Check your Android device’s Bluetooth settings to confirm that media audio is enabled for the N-Com B1.

4. Firmware Update Needed: Updating the B1 system firmware may resolve compatibility issues.

5. Bluetooth Prioritization: If the GPS is connected via a different device (such as a separate GPS unit), the phone’s navigation audio might not be prioritized.

Try checking Bluetooth settings, ensuring correct pairing, and updating the firmware.

This answer is automatically generated

Summary of Contents for N-Com B1

  • Page 1 Firmware Version: 1.xx USER INSTRUCTIONS AND SAFETY v.04...
  • Page 2 For additional information about B1, and to download high- definition instructions as well as the latest Firmware version, visit the website www.n-com.it REFERENCE STANDARDS The products of the N-Com line are in compliance with standards as per the table below: Bluetooth system...
  • Page 3: Table Of Contents

    1.5.Qualified personnel ............... 5 1.6.Accessories and batteries ............5 1.7.Disposal ................6 CONTENT OF THE PACKAGING ..........6 INSTALLATION ..............7 3.1.Removing the B1 system from the helmet........10 BASIC FUNCTIONS............. 11 4.1.N-Com Wizard ..............11 4.2.N-Com App .................11 PAIRING UP BLUETOOTH DEVICES ........12 5.1.Affiliation reset function ............12...
  • Page 4: Warnings And Safety

    Read this User Manual carefully, as well as the User Manuals for other N-Com kits that you will be using with the N-Com B1. Read the simple rules listed below. Failure to comply with these rules may lead to dangerous situations.
  • Page 5: Qualified Personnel

    Caution: Adjust the volume of the N-Com system (where provided) and of the audio sources connected to it before you use the system on the road. Caution: Adjusting the volume to very high levels may cause damage to your hearing.
  • Page 6: Disposal

    1.7. Disposal Refer to this user manual and to manuals related to other parts of the N-Com system in order to disassemble the system from the helmet. Once the system has been disassembled, dispose of it according to the following instructions: The presence of a crossed-out wheelie bin indicates that in the European ...
  • Page 7: Installation

    (Fig.1) Fig. 1 Before you install the B1 system on the helmet, make sure it turns on properly. Press  the “on” key for about 2 seconds, until the LED lights up and you hear a beep in the headset.
  • Page 8 Option 2: remove the left and right side filling material as well as the filling material in the housings of the N-Com earpieces located in the EPS cheek pads. Option 1 Option 2 N.B.: Keep the filling material in case you wish to use the helmet without the N-Com system in the future. Place system special ...
  • Page 9 Fix the cable inside the helmet and  make sure the right fixing clip snaps into its housing (Fig. 5) Fig. 5 Position microphone  housing on the left of the helmet, inserting metal boom groove found chin guard coupling frame (Fig. 6). Caution: make sure that the side of the microphone support with the writing “N- Com”...
  • Page 10: Removing The B1 System From The Helmet

    Unhook the right and left clips from  the shell, levering upward using a flat head screw (or a similar tool), as shown in figure 9. Fig. 9 Completely remove the B1 system from the helmet and re-install the cheek padding  and the gasket.
  • Page 11: Basic Functions

    B1 system. The programme can be downloaded from the Internet site www.n-com.it, in the “Download” section. In order to use it, a helmet equipped with B1 must be connected to the PC, using the USB cable supplied with the system.
  • Page 12: Pairing Up Bluetooth Devices

    Select the N-Com device. If a password is requested, enter 0000 (four zeros); B1 will confirm the pairing up by means of a tone in the headset, and the LEDs will stop flashing; Turn off and on both the device and the B1 to store the pairing up data.
  • Page 13: Mobile Phone Functions

    B1 allows a conference call with Rider and Pillion Passenger. When a call comes in on a mobile phone connected via Bluetooth to B1, the Rider-Pillion Passenger intercom is temporarily turned off. However, if you wish to share the phone call with the other helmet, simply turn on the intercom manually during the phone call (by briefly pressing “on”).
  • Page 14: Bluetooth A2Dp Music Player

    10. RIDER-PASSENGER INTERCOM MODE In order to use B1 in wireless intercom mode, both helmets have to be equipped with a N- Com Bluetooth system. In order for two N-Com systems to communicate with one another, they have to be paired up first.
  • Page 15: Intercom Function

    11.2. Recharging the system To recharge the B1 system, connect the USB cable to a battery charger or to a powered USB port. Charging occurs as follows: When you connect the B1 system to the battery charger, the blue LED begins to flash.
  • Page 16: Summary Table Of Controls

    Play music (Play) (2s) Pause Function (Pause) (2s) Next track (Forward) (4s) Pairing up mode - system turned off (4s) Rider-Passenger intercom pair up Erase pair ups** (4s) *Briefly press at the same time. **With N-Com system in Pairing up Mode.
  • Page 17: Limited Warranty

     Negligence and normal wear of internal and external parts.  Any damage caused by an accident;  Any change or modification made to the helmet or to the N-com system by the user or by third parties.  Color changes or damages caused by exposure to harmful chemical products.
  • Page 18: Procedure For The Forwarding Of Claims

    Legislative Decree 2 February 2002 n. 24. 13.5. Product identification N-Com products are identified by means of a code that allows product traceability identification. The identification code is printed on the adhesive label applied to the B1 system, under the rechargeable battery.
  • Page 19: Warranty Registration Form

    14. WARRANTY REGISTRATION FORM Product name: Identification code Buyer’s Information Name Last name Address Phone e-mail Dealer’s stamp Date of purchase...
  • Page 20 B1v04 - 26/03/2015 17:31:00 Printed on recycled paper...

Table of Contents

Save PDF