FACE AVANT . COMMUTATEUR DE SELECTION DE LA SOURCE Ces commutateurs sont utilisés pour sélectionner la source d’entrée de chaque canal. Chaque canal ne peut être assigné qu’à une seule source d’entrée à la fois. La position « PHONO » doit être utilisée pour le raccordement d’une platine pour disque vinyle.
Page 3
3. CONTROLE DE GAIN DU CANAL Ce réglage est utilisé pour ajuster le gain du signal sonore d’entrée du canal. Ne jamais utiliser le contrôle de gain pour régler le volume de sortie. Régler le gain correctement permet de vous assurer un signal de sortie propre.
Page 4
11. AUX/In Entrée jack pour entrer une ligne comme un lecteur à bandes ou un retour de machine à effets. 12. EGALISEUR MICROPHONE Le canal du microphone inclut une égalisation deux bandes. Ces réglages permettent d’augmenter ou de diminuer les basses et les aigus du signal de sortie. BOUTON MIC TREBLE –...
Page 5
FACE ARRIERE 17. ENTREE PHONO RCA Connectez les platines vinyles, équipées d’une carte MM pickup, aux entrées phono (toutes les platines DJ sont équipées d’une carte MM pickup). Le RCA rouge représente l’entrée du canal droit et le RCA blanc l’entrée du canal gauche. 18.
Page 6
24. COMMUTATEUR D’ENTREE Ce commutateur sélectionne l’entrée entre Phono (RIAA) ou Line sur la face arrière. 25. ENTREE USB Le canal d’entrée/sortie USB est utilisé pour lire des fichiers MP3 (ou autres format audio) d’un ordinateur ou pour enregistrer vos performances sur ordinateur. La connexion USB s’utilise sur le canal 1. SPECIFICATIONS TECHNIQUES ALIMENTATION AC9V, 1000mA...
Page 7
Fader Kill CHANNEL FADER Plus de 75dB à 1KHz CROSSFADER Plus de 70dB à 1KHz Interface USB A/D & D/A : 16 bit Delta Sigma Playback : Distorsion < 0.05% Ratio Bruit : 80dB Enregistrement : Distorsion < 0.1% Interface: USB1.1 ou USB2.0 avec fonctionnement en duplex intégral (enregistrement et lecture) ATTENTION L’appareil ne doit pas être exposé...
Page 8
FRONT PANEL . SOURCE SELECTOR SWITCH These switches are used to select the input source assigned to each channel. Each channel may only be assigned one input source at a time. This switch must be in the “phono” position for turntable operation. 2.
Page 9
control to adjust output volume. Setting the gain level properly will ensure a clean output signal. 4. MASTER VOLUME CONTROL This rotary knob is used to control the master output level (volume). To avoid distorted output try to maintain an average output signal level +4 dB. Be sure this volume control is always set to zero before turning the unit on.
11. AUX Input Input jack for line level input like professional tape machines or effects unit returns. 12. MICROPHONE EQUALIZER The microphone channel includes a two-band signal EQ. These controls are used to increase or decrease the LOW’s and HI’s of the output signal. MICROPHONE TREBLE CONTROL –...
REAR PANEL 17. PHONO INPUT JACKS Connect turntables equipped with MM pickup cartridge to PHONO inputs (All DJ turntable use MM pick-up cartridges).The red colored RCA jack represents the right channel input and the white represents the left channel input. 18.
25. USB Jack The USB input/output channel is used for playing MP3 (or other audio) files from a computer or for recording your performance to a computer. The USB jack sends audio to the mixer’s channel 1. TECHNICAL SPECIFICATIONS POWER SUPPLY AC9V, 1000mA DIMENSIONS 254mm x 310mm x 100mm...
Page 13
Mic Talkover -14dB (+/-2dB) Fader Kill CHANNEL FADER More than 75dB at 1KHz CROSSFADER More than 70dB at 1KHz USB Interface A/D & D/A: 16 bit Delta Sigma Playback: Distortion < 0.05% S/N: 80dB Recording: Distortion < 0.1% Interface: USB1.1 or USB2.0 with full-duplex operation (playback and recording) CAUTION: The apparatus shall not be exposed to dripping or splashing and that no objects filled with liquids, such as...
Need help?
Do you have a question about the NSA 2000 and is the answer not in the manual?
Questions and answers