Advertisement
11
10
1
2
A
4
3
E
TECHNICAL
SPECIFICA-
Operating Voltage
10.5 to 28V DC 250mA max (ALL LED's LIT)
Power on Indication
Outlets
Variable Gain
(per Outlet)
Frequency Range
47Mhz to 860Mhz (FM / DAB / TV) to all outlets (F connection)
Flatness
Noise Figure
Signal Indication
41dBµV=1 LED to 90dBµV=12 LEDS
(Sensitivity - 5 multiplexes
6 LED's = 65dBµV on outlet sockets, the preferred level for
averaged)
Dimensions 16.5x5.5x2.7cm
12
6
5
1...........Power 'ON' LED
2...........Power Switch
3...........2.5mm DC Power inlet Jack
4...........Aerial Connection
5,6,......TV/Radio outlets
9...........Gain Adjust
10.........'Low Signal'
Orange
LEDs
11.........'Good Signal'
Green
LEDs
12.........'High Signal'
Orange
LEDs
A,B........Fixing Holes
C...........Fixing screws
D...........DC Power Cable - 2.5mm
E...........30cm Aerial Hook-up patch lead
Easy-Tune 2 Way
Yes, Red LED
2
5-19dB
+/-1.5dB
<2.9dB
reliable digital TV reception
125 grams
INSTALLATION
Your Easy-Tune unit may be permanently fixed inside a convenient stowage compartment using the
supplied screws (C). Fixing centres (A,B) are 15cm apart. Ensure that it is safe to install the
fixing screws into the chosen surface.
1. Connect 12/24V ONLY to the power inlet jack (3) i.e. from your leisure battery circuit or a
suitable 240V mains to 12V adaptor with 2.5mm jack plug (+ve centre pin) and capable of
delivering 250mA. (A suitable 240V Power adaptor is available from Happy Wanderer or their
B
resellers).
The supplied power cable (D), must be connected to a 12/24V supply. Please refer to your caravan
handbook for details of where this lead may be connected. If you are unsure as to how to do this,
then please consult a qualified electrical technician. All Easy-Tune are internally fused, however we
recommend a fused outlet of no more than 5 amps in order that the cabling is protected. The
9
wiring convention is thus:
CENTRE PIN positive, i.e. connect the STRIPED conductor of the DC power cable (D) to the
POSITIVE terminal of your 12/24V supply. The Easy-Tune / Easy-Boost units are polarity
protected so incorrect connection will not damage the unit, it simply will not operate.
2. Connect the Hook-up lead (E) between the Aerial connection (4) and your aerial through-wall
connection socket.
3. Connect your TV / Radio leads to the outlets (5,6). All outlets can be either TV or radio,
provided the connected aerial is suitable for TV and radio.
4. Switch the Power Switch (2) to the ON position (l). The Power ON LED (1) will be lit.
5. You are now ready to start using your Easy-Tune unit
OPERATION
Your Easy-Tune unit is designed to indicate the presence and strength of a DIGITAL or ANALOGUE
TV signal. In doing so it is able to assist in indicating when your aerial is pointing towards the best
direction for your location. It is also able to boost the received signal for optimum performance and
distribute to 2outlets.
1. Turn on the Easy-Tune unit (2) if not already done so.
2. Rotate the Gain Adjust control (9) to maximum setting i.e fully clockwise.
3. Rotate your aerial whilst observing the LED's.
4. The aim is to rotate your aerial until you get the maximum number of LED's to light. You may
need to decrease the Gain control (9) slightly if all 12 of the LED's illuminate.
5. Once the best direction has been established, adjust the Gain control (9) to light as many
LED's (11) as possible. The Easy-Tune LED's are factory calibrated such that 4
indication of 65dBµV signal level - Which is the preferred level for reliable digital TV reception.
6. The High Signal
control (9) needs to be decreased.
7. The Low Signal
needs to be increased.
8. Once the optimum direction and level of Gain has been established, you may now tune your TV
and that's it, you're done.
9. You may be in a location where only the Low Signal
maximum gain, you should still attempt to tune your TV as this indicates that TV service does exist,
albeit not as many channels as you may normally expect to find.
N16369
NEVER connect 240V ac Mains directly to this unit!
Orange
LED's (12) indicate when you may have too much signal and the Gain
Orange
LED's (10) indicate when you have minimum signal and the Gain Control
Orange
Green
Green
LED's lit is an
LED's (10) light up, even on
Advertisement
