Advertisement
Quick Links
Free to Air Broadcasting
Satellite Receiving Systems
Campersat
Digital Systems
Campersat Autoseek Autoskew System 4441
Campersat Autoskew Single LNB
Campersat Autoskew Twin LNB
Supplementary Installation Handbook
August 2008
© 2008
Campersat Division of Videosat Pty Ltd
Systems Engineering
2/28 Salisbury Road Hornsby NSW 2077
PO Box 3190 Asquith NSW 2077
Tel (02) 9482 3100
Fax (02) 9482 3999
videosat.com.au
campersat.com.au
Campersat AutoSeek Autoskew
1
H4441 Build 4441 August 2008
Advertisement
Summary of Contents for Campersat Satellite system
- Page 1 Campersat Autoskew Single LNB Campersat Autoskew Twin LNB Supplementary Installation Handbook August 2008 © 2008 Campersat Division of Videosat Pty Ltd Systems Engineering 2/28 Salisbury Road Hornsby NSW 2077 PO Box 3190 Asquith NSW 2077 Tel (02) 9482 3100 Fax (02) 9482 3999 videosat.com.au...
-
Page 2: Installation Instructions
Auto Skew CI FITTING INSTRUCTIONS Autoseek Autoskew It is no problem to fit an Autoseek Autoskew fully automatic satellite system onto any vehicle. However, you should take care with some specific points and therefore, PLEASE READ these instructions carefully before starting your work, to obtain the very best results later on whenever you use your new system. - Page 3 Spend a minute to think about twiring,(downwards to the receiver) that will be needed later on. It is much easier to install the wiring on top of the roof than inside the vehicle. Campersat AutoSeek Autoskew H4441 Build 4441 August 2008...
- Page 4 When hiding the receiver inside, check if its ventilation is sufficient. 5cm (2 inches) of distance from anything around would be best. Make sure to find a way to do all the required wiring. 2c. Sat-Mouse Campersat AutoSeek Autoskew H4441 Build 4441 August 2008...
- Page 5 6 screws afterwards. Before applying the glue, clean the roof and the plate with cleaning liquid. When done, apply glue onto the bottom side of the mounting plate. Put the plate onto the position that you decided on before. Again Campersat AutoSeek Autoskew H4441 Build 4441 August 2008...
- Page 6 Push or pull the cable through the elbow until you have a proper length outside the vehicle. It will be very difficult to shift the cable after the final fitting of the Campersat AutoSeek Autoskew H4441 Build 4441 August 2008...
- Page 7 The AutoSkew requires a 12V or a 24V DC power supply. We recommend a 12V supply. Any voltages above 30V or any AC voltages will destroy the receiver absolutely. This will NOT be covered by warranty. Campersat AutoSeek Autoskew H4441 Build 4441 August 2008...
- Page 8 (25mm² and up).In case of any trouble try to bypass such a unit to see if it fixes the trouble. Any fuse along the power line should be between 10A and 20A. Campersat AutoSeek Autoskew H4441 Build 4441 August 2008...
- Page 9 Be sure to beam the remote towards the sat-mouse while pressing EXIT and to mount the batteries into the remote before this operation. When the arm is approximately vertical and stopped, you can fit the dish onto the arm. Campersat AutoSeek Autoskew H4441 Build 4441 August 2008...
- Page 10 Satellite Output Connect the Coax cable from the control unit Sat out to the LNB switch kit at • the Campersat dish connection. Connect receiver 1 to Sat receiver A & receiver 2 to Sat receiver B. Campersat AutoSeek Autoskew...
-
Page 11: Video Output
Onscreen Display menu coming from the AutoSkew receiver. Press the red button on the AutoSkew remote again to retract the dish. With the dish retracted the AutoSkew should switch to Standby immediately. Campersat AutoSeek Autoskew H4441 Build 4441 August 2008... - Page 12 If after a few minutes the dish has not found the satellite, press exit and go to search via location and ensure it is searching from your current location. eg Sydney NSW Should you be unsuccessful, select the nearest location to your current one and press Campersat AutoSeek Autoskew H4441 Build 4441 August 2008...
- Page 13 Press exit, and then exit once again • 3. You will then be prompted to save settings. Press OK to confirm. 4. Next press exit to exit the menu. Select TV will now be operational. Campersat AutoSeek Autoskew H4441 Build 4441 August 2008...
- Page 14 Campersat AutoSeek Autoskew H4441 Build 4441 August 2008...