Download Print this page
DKS MicroPLUS 8055 Instruction Manual

DKS MicroPLUS 8055 Instruction Manual

Rf receiver

Advertisement

Quick Links

MODEL 8055 MicroPLUS
The model 8055 is a High Security Encrypted "Rotating Code" RF Receiver that is designed ONLY for use with MicroPLUS
typically installed in automatic garage door openers and vehicular gate operators. The encrypted "Rotating Code" programming in this receiver and
®
the companion MicroPLUS
receiver can store up to 40 MicroPLUS
Installation
This receiver is NOT designed to be installed outdoors without being protected from the weather. An outdoor enclosure is available for the
8055-081 receiver if required (P/N 8057-110 - Metal Outdoor Box).
Install the 8055 receiver in a location so the antenna is NOT surrounded by metal and is in free air as high as possible above the ground.
A longer Coax Antenna kit is available for the 8055-081 receiver if required (P/N 1514-073 - Includes antenna, mounting "L" bracket and 15 feet of
coax cable).
R e
c e i
v e r
T e r
m i
n a
l
Receiver Terminal Wiring
#1 & #3 Power:
Connect 12 - 24 Volt AC or DC
power to terminals #1 and #3.
If DC power is used (Transformer):
Terminal #1 is NEGATIVE and terminal #3 is POSITIVE.
Use minimum 18 AWG wire to power the receiver.
#2 Relay:
Normally Open (N.O.) relay
contacts are provided on terminals #1 and #2.
Relay is rated for 30 volts, 1 amp max.
Garage Door Opener:
To connect the 8055
receiver directly to a typical garage door opener,
connect terminals 1, 2 and 3 on the receiver to
terminals 1, 2 and 3 on the garage door opener.
transmitters prevent copied transmitter codes from being used again to operate the garage door or gate. The 8055
®
transmitter codes in its memory.
Gate
Operator
Typical
Garage
Door
Opener
®
RF RECEIVER
P/N 8069-080
Built-In
Antenna
R e
12-24 Volt Transformer
From "Low Voltage Common"
From "Radio Open"
From "Circuit Board" Power
1
2
3
8055-080
Built-In Antenna
P/N 8070-080
®
Use ONLY MicroPLUS
Transmitters
c e i
v e r
T e r
m i
n a
l
Polarity Matters!
To Receiver Termnal #1 (Neg.)
To Receiver Termnal #3 (Pos.)
To Receiver Termnal #1
To Receiver Termnal #2
To Receiver Termnal #3
To Receiver Termnal #1
To Receiver Termnal #2
To Receiver Termnal #3
Inglewood, California 90301
DoorKing Part Numbers
8055-081
Coax Antenna Kit
®
transmitters and is
P/N 8071-080
F Connector
18" Coax Cable
Coax Antenna Kit
(Included)
120 Glasgow Avenue
U.S.A.

Advertisement

loading

Summary of Contents for DKS MicroPLUS 8055

  • Page 1 8055-081 receiver if required (P/N 8057-110 - Metal Outdoor Box). Install the 8055 receiver in a location so the antenna is NOT surrounded by metal and is in free air as high as possible above the ground. A longer Coax Antenna kit is available for the 8055-081 receiver if required (P/N 1514-073 - Includes antenna, mounting “L” bracket and 15 feet of coax cable).
  • Page 2 DoorKing Part Numbers Programming 8055-080 8055-081 Built-In Antenna Coax Antenna Kit Programming Push Button Programming LED Programming Transmitter Codes: Press and hold the programming push button (about 2 seconds) until the programming LED quickly flashes ONE time, then release the button. The programming LED will flash once every two seconds indicating that you are in the transmitter programming mode..