Table of Contents
Advertisement
Recording from a Digital Satellite Receiver
[HDD] [RAM] [-R] [-RW‹V›] [+R] [+RW]
Manual Recording
This unit cannot record NTSC signals to discs that
already have PAL signal recordings. (However, both
types of programmes can be recorded onto the HDD.)
Preparation:
]RAM\ If the disc is protected, release protection
(
58).
Connect a digital satellite receiver to this unit's AV2
input terminals (
When the output signal from the external equipment
is NTSC, change the "TV System" to "NTSC" in the
Setup menu (
With the unit stopped
INPUT
SELECT
digital satellite receiver you have
connected.
DRIVE
SELECT
− If you selected the DVD drive, insert a disc
(
17).
REC MODE
mode.
Select the channel on the digital
satellite receiver.
REC
Tips
To skip unwanted parts
Press [] to pause recording. (Press again to restart recording.)
To stop recording
Press [].
Downloaded From Disc-Player.com Panasonic Manuals
11).
65).
to select "AV2" for the
to select the HDD or DVD
drive.
to select the recording
to start recording.
Linked timer recordings with external
equipment (SKY Digital STB/digital satellite
receiver) — EXT LINK
To record programmes from a SKY Digital STB/digital
satellite receiver using timer programming
Preparation:
]RAM\ If the disc is protected, release protection
(
58).
Make sure you connect the AV2 terminal of this unit
to "VCR Scart Terminal" of a SKY Digital STB/digital
satellite receiver with a 21-pin scart cable (
Set the "AV2 Input" and "Ext Link" to match the
connected equipment in the Setup menu (
Make timer programming on
SKY Digital STB/digital satellite
receiver.
− Refer to the equipment's operating instructions.
to select the HDD or DVD
DRIVE
SELECT
drive.
− If you selected the DVD drive, insert a disc
(
17).
EXT LINK
− The unit turns off and "EXT-L" lights on the
unit's display to indicate timer recording
standby has been activated.
− While the unit is in EXT LINK standby mode
or recording, most operations on this unit are
prohibited ([ OPEN/CLOSE], [/l] etc.).
When you operate, press [EXT LINK] to
cancel EXT LINK standby mode or recording
(The unit turns on and "EXT-L" disappears.).
Tips
To cancel the external control
Press [EXT LINK] to stop recording or to cancel linked timer recording
standby (The unit turns on and ''EXT-L" disappears.).
Manual timer recordings (
28)
Notes
In order to prevent accidental operation, press [EXT LINK] to cancel
the setting after recording is fi nished.
This function does not work when "TV System" is set to "NTSC" in
the setup menu (
65).
This function does not work with some equipment. Refer to the
equipment's operating instructions.
The beginnings of recordings may not be recorded correctly in some
cases.
When "Ext Link" is set to "Ext Link 2", this function does not work if
the input signal is NTSC system.
Programmes are recorded as one title on this unit when the end
time of the earlier timer recording and the start time of the later timer
recording are close to each other.
[HDD] [RAM] To divide the titles, go to "Divide Title" (
When this unit is in EXT LINK standby ("EXT-L" is shown on the
unit's display), the TV Guide data cannot be downloaded.
While the unit is in EXT LINK standby mode or recording, AV1 output
terminal outputs the signal which is input from the AV2 input terminal
irrespective of "AV1 Output" setting (
During EXT LINK standby mode or recording, playback is only
available from the drive performing the recording.
When "EXT-L" lights on the unit's display, Direct TV Recording is
unavailable.
11).
65).
46).
65).
27
Advertisement
Table of Contents
