Advertisement
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Summary of Contents for Flight Deck SC-6502
- Page 1 SI-7AP1E SERVICE INSTRUCTIONS Cycle Computer SC-6502 / SC-6501/ SC-M500...
-
Page 2: Display Modes
“Current speed” and “Gear indicator (bar)” are always displayed riding, otherwise you might have an accident. mode 1 mode 2 Specifications Clock Cadence Meter SC-6502 SC-6501 / SC-M500 Bracket/Sensor unit SM-SC70 SM-6501 SM-6501-MD SM-6501-M Trip time Main display cadence ST-7700-C... -
Page 3: Display Contents
2. Display Contents mode 1 mode 2 Current speed Clock Cadence (VEL) (CLK) (rpm) Stop watch– trip distance No. of gear teeth Trip time Stop watch (DST STW) Main display Lap counter (digital) (TIM) cadence Stop watch– Gear indicator average speed Trip distance Maximum (bar) -
Page 4: Name And Function Of Each Part
3. Name and function of each part ( 1 ) Current speed ( VEL ) km/h, mph 0.0 (2.0) - 130.0km/h Front 0.0 (1.2) - 80.0mph (Range) When main The current speed will appear at display cadence the top of the main display. appears on top Main Display 1. - Page 5 ( 4 ) Trip distance group ( TIM, DST, MAX, AVE ) ( 5 ) ODO meter ( ODO ) 0 - 99999.9 km, mile The trip distance group includes the trip time (TIM), trip distance (DST), maximum Displays the cumulative distance speed during the trip (MAX) and the average speed during the trip (AVE).
- Page 6 ( 7 ) Cadence ( rpm ) ( 10 ) Digital number of gear teeth ( F- R ) Cadence is calculated from the F - R Gear combinations are displayed when a shift has gear tooth numbers and current been made.
-
Page 7: Setting Tolerances
4. Changing the setting data and 5. Viewing data after removing the the bicycle number computer from the bracket mount Changing the Changing the The data can still be viewed even when the computer has been removed setting data bicycle number from the handlebar bracket. -
Page 8: Data Input
( 4 ) Installing the magnet and 7. Installation to the bicycle Fig.4 Ø 2.1mm or less sensors Use a screwdriver to temporarily secure Install the levers to the handlebars. Then connect and adjust the brake and the magnet to a spoke on the right hand shifting cables. - Page 9 The display will appear as shown in fig9, Enter the value which was Example Roll forward measured previously. Fig.9 Switch “B”: 2028 - 2032mm 2030mm • • • • • • Accept 2033 - 2037mm 2035mm • • • • • • 2050 Tire circumference (mm) •...
- Page 10 ( 4 ) Entering the number of chainring and sprocket teeth Enter the number of teeth for the inner chainring (for double front The display will then change to that shown in fig10. Fig.12 chainwheel) or the middle Switch “B”: chainring (for triple front Accept Fig.10...
-
Page 11: Replacing The Battery
If the cassette has seven sprockets, press switch “A” once to change the The hours will advance when switch “A” is Fig.17 flashing “21” to “- -”, and then press switch B once. This will indicate that pressed. If switch “A” is pressed continuously, there is no 8th sprocket, and the operation for entering the number of the hours will advance rapidly. -
Page 12: Trouble Shooting
@ @ @ @ @ @ @ @ e ? @ @ @ @ @ @ @ @ e ? @ @ @ @ @ @ @ @ ? e @ @ @ @ @ @ @ @ e ? @ @ @ @ @ @ @ @ ? e @ @ @ @ @ @ @ @ e ? @ @ @ @ @ @ @ @ ? e @ @ @ @ @ @ @ @ e ? @ @ @ @ @ @ @ @ ? e @ @ @ @ @ @ @ @ e ? @ @ @ @ @ @ @ @ ? e @ @ @ @ @ @ @ @ e ? @ @ @ @ @ @ @ @ ? e @ @ @ @ @ @ @ @ e ? @ @ @ @ @ @ @ @ ? e @ @ @ @ @ @ @ @ @ @ @ @ @ @ @ @ e ? @ @ @ @ @ @ @ @ e ? @ @ @ @ @ @ @ @ ? e @ @ @ @ @ @ @ @ e ? @ @ @ @ @ @ @ @ ? e @ @ @ @ @ @ @ @ e ? @ @ @ @ @ @ @ @ ? e @ @ @ @ @ @ @ @ e ? @ @ @ @ @ @ @ @ ? e @ @ @ @ @ @ @ @ e ? @ @ @ @ @ @ @ @ ? e @ @ @ @ @ @ @ @ e ? @ @ @ @ @ @ @ @ ? e @ @ @ @ @ @ @ @ e ? @ @ @ @ @ @ @ @ ? e...
Need help?
Do you have a question about the SC-6502 and is the answer not in the manual?
Questions and answers
does display appear when unit is removed from bicycle?
Yes, the display of the Flight Deck SC-6502 can be viewed even when the computer has been removed from the handlebar bracket.
This answer is automatically generated