Download Print this page

Cycle Sounds Handlebar Speaker Installation Instructions Manual

Amplified handlebar speaker kits

Advertisement

Quick Links

Installation Instructions
Amplified Handlebar Speaker Kits
Note: Audio quality is also dependent upon the device with which the amplifier is
being used with. For best results Cycle Sounds recommends that you use an
audio source with a high millivolt output such as an iPod or modern Smart Phone.
Also adjusting the equalizer for the type of music being played will make your
product work and sound better as well. See STEP-10 for more information.
All Cycle Sounds products have a warranty period of 1 year from the date of
original purchase. This warranty covers the cost of parts only for any needed
repairs to, or replacement of, your unit for 1 year under normal usage. (Labor for
removal or reinstallation of speaker kits and shipping cost are not covered by this
warranty). Any product modified from its original manufactured form or installed
improperly, shall not be covered by this warranty. This does not include
modifications that are required for normal installation as outlined in the
instructions below. Specifically, you should not cut any wires, remove quick
connectors or cut/bend brackets or you risk voiding the manufacturerʼs warranty.
Warranty Notice - When returning products for warranty service a copy of the
original sales receipt or proof of purchase must be sent in the package
accompanying the product. Failure to do so will delay your warranty service.
Warning: The use of a radio, iPod, MP3 player, satellite radio, or any other
device on a motorcycle increases the risk of riding. Riders must always pay
attention while operating their motorcycles. Always make volume and tuning
adjustments when motorcycle is not in motion. Failure to not do so could result in
serious or fatal injuries.
Failing to follow all installation instructions and recommendations carefully can
result in damage to your product, damage to your motorcycle, personal injury or
even death.

Advertisement

loading
Need help?

Need help?

Do you have a question about the Handlebar Speaker and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Cycle Sounds Handlebar Speaker

  • Page 1 See STEP-10 for more information. All Cycle Sounds products have a warranty period of 1 year from the date of original purchase. This warranty covers the cost of parts only for any needed repairs to, or replacement of, your unit for 1 year under normal usage.
  • Page 2: Parts List

    Parts List: (2) Bullet Speakers (2) P-Clamps (1) Mini Amplifier (1) Amplifier Bracket (1) Amplifier Power Harness (1) Universal Handlebar MP3 Bracket (2) 1/4" x 20 x 3/8” Amplifier Mounting Bolts (S.S.) (2) 5/16” x 24 x 1/2" Speaker Bolts (chrome) (1) 5/16”...
  • Page 3 Step-2: Attach Amplifier Bracket to Motorcycle There is a few locations the amplifier mounting bracket can be attached and these locations may vary greatly depending on your make, model and installed accessories. Most importantly, you need to pay close attention to keep the amplifier bracket away from the front fender when the suspension is compressed.
  • Page 4 Fig. 2-3 Fig. 2-4 C) On a Sportster, mount the amp bracket to the bottom of the A frame using the lower engine guard (crash bar) bolt locations as shown in figure 2-5. If you have an engine guard installed you will need to detach the bottom 2 bolts to install the amplifier bracket.
  • Page 5 Step-3: Secure Amplifier Harness to Frame Once the amplifier bracket is attached, secure the amp harness to the frame using the supplied wire ties (12) making sure to keep wiring away from moving parts and high temperature heat sources such as the exhaust and engine covers. Step-4: Attach Speakers to Handlebars There are a couple of different ways to mount the bullet speakers depending on what series speakers you are installing and what type of bike is being installed...
  • Page 6 Note that the speakers can be attached to p-clamps in either direction depending on available space and installed equipment such as a windscreen. When securing the speakers for final placement, remember that they should be pointed as close to your ear level as possible for the best results. Note: Installation using the mirror stem Z-brackets can only be done with the Series 1 and Series 2 speakers on a Harley-Davidson motorcycle and will not be included in other kits as they canʼt be used in...
  • Page 7 and speakers on some bikes. To adjust, simply loosen the speaker/mirror stem bolt and rotate until a suitable location is found. Also make sure the brackets do not interfere with the throttle control or any other cabling when turning the handlebar when finished. Step-5: Route the Speaker Wires and Amplifier Input Wire Once the speakers are secured on the vehicle route the speaker wires down the bars making sure to leave enough slack so the wires can be neatly secured when...
  • Page 8 When running your power and speaker wiring you can use a rigid ʻsnakeʼ tool (or something similar) to get to the battery area, underneath gas tanks and around other obstacles. Generally you do not need to remove gas tanks to install our speaker system and achieved by using this technique. Start by running the snake tool from the battery area under the tank and out by the neck of the bike.
  • Page 9 4. Last, route the black wire to a good ground location on the vehicle. This can be on the frame or another ground wire. Crimp the provided Blue Ring Terminal (14) on the black wire and connect to the ground location on the vehicle (figure 6-6) or use alternative methods to connect the ground wire.
  • Page 10 Step-7: Connect Speakers and Finish Wiring Finish routing the speaker wires to the amplifier and connect them using the attached 2-pin quick release connectors as shown in figure 7-1. Bundle any extra wiring so it can be neatly tucked away underneath gauges, covers, lights, etc.
  • Page 11 Use any 4-hole AMPS mount device cradle or holder with the universal mp3 bracket AMPS hole pattern. The 4-hole AMPS mount pattern is an industry standard and our Mp3 bracket is compatible with most Cycle Sounds device cradles and holders (iPhone, iPod, Droid, etc.) as well as many other manufacturersʼ...
  • Page 12 If you are having problems with sound clarity this could be a factor. More information can be found about this in an iTunes tutorial on our website at www.cyclesounds.com. Cycle Sounds® LLC Toll Free: 1(866) 427-2346 Office: (816) 525-2628 275 NW Victoria Drive Leeʼs Summit, Missouri 64086...

This manual is also suitable for:

Series 1Series 2