DELTA DORE TYXIA 411 Installation And User Manual

Installation and User Guide
TYXIA 411
Lighting receiver switch

Warnings

• Carefully read these instructions prior to instal-
lation.
• The unit must be installed in compliance with
currently applicable standards.
• Always switch off the mains before installing or
servicing the unit.
• Do not attempt to repair the unit yourself; an
after-sales service is available.
• Check that the fastenings are suited to the sur-
face that the unit will be attached to (plaster-
board, brick, etc.).
• The diagrams provided are simplified for grea-
ter clarity. The protective units and other
accessories required by the standards are not
illustrated.
Standard UTE NF C15-100 and good practice
must be complied with. Connected or nearby
equipment must not generate excessive inter-
ference (directive 2004/108/EEC).

Two-way switch mode

Connection
TYXIA 411
Existing
switch
T L R N N
Operating the TYXIA 411
Pressing the button changes the current state
(on or off).

Simple lighting mode with an associated TYXIA transmitter

The simple lighting mode can be controlled by a
TYXIA transmitter (transmitter switch, key ring
remote control, etc.).
The receiver can record up to a maximum of 8
associations (buttons, transmitters, etc.).
ON OFF
ON OFF
(recommended for controlling
exterior lighting)
or
ON
Either is possible, depending on the scenario.
DELTA DORE
Bonnemain - 35270 COMBOURG - France
E-mail : deltadore@deltadore.com
Device complying with the requirements of the
R&TTE 1999/5/EC directives
Because of changes in standards and equipment, the characteristics given in the
text and the illustrations of this document are not binding unless confirmed by
Delta Dore.

Remote control switch mode

Connection
T L R N N
IMPORTANT:
Do not connect
terminal 3 for
this application.
Remote control switch
Operating the TYXIA 411
Pressing the button changes the current state
(on or off).
Operation with a transmitter
associated TYXIA or TYDOM
IMPORTANT: he two-way switch mode can only be
controlled by a (TYXIA) or
(TYDOM 200).
N 230 V
50 Hz
L
(status being modified)
Press the receiver button until the LED flashes
(~3 seconds).
2 possible choices.
Slow flashing: two-way switch mode
Rapid flashing: remote control switch mode (unused).
Press the receiver button to pass from one rate
of flashing to the other.
Select the slow flashing.
Associating a button
Press the receiver button until the LED flashes
(~3 seconds).
2 possible choices.
Slow flashing: simple lighting mode
Rapid flashing: remote control switch mode (unused).
Press the receiver button to pass from one rate
of flashing to the other.
Select the slow flashing.
On the transmitter, press and hold the
down for approximately 5 seconds. The LED will light
up, go out, then light up again. Release.
Check that the receiver's LED is no longer flashing.
The transmitter button is associated with the
receiver.
OFF

Installation

Location

The receiver must be fitted on a flush-mounted box
(Ø 65 mm) that will receive the live and neutral
wires.

Connecting and mounting the product

Connect the product
(see adapted connec-
tion according to your
application), then posi-
tion it by orienting the
terminal upwards.
Secure it by tightening
the screws without for-
cing them.
Operation with a transmitter
TYXIA 411 associated TYXIA or TYDOM
IMPORTANT: The receiver is delivered in simple
lighting mode. To use it in remote control switch
mode, it must be associated with a transmitter.
The remote control switch mode can only be
controlled by a
N
230 V button).
50 Hz
L
L
N
Press the receiver button
until the LED flashes (~3 seconds).
2 possible choices.
Slow flashing: simple lighting mode
Rapid flashing: remote control switch mode.
Press the receiver
rate of flashing to the other.
Select the rapid flashing.
On the transmitter, press and hold the
for 5 seconds. The LED will light up, go out, then
light up again. Release.
Check that the receiver's LED is no longer flashing.
button
The transmitter button is linked with the
receiver in two-way switch mode.
To link a TYXIA 411 with a TYDOM 200, please
refer to the TYDOM 200 guide.
or
Associate
Press the receiver button
(~3 seconds).
2 possible choices.
Slow flashing: simple lighting mode
Rapid flashing: remote control switch mode (unused).
Press the receiver
of flashing to the other.
Select the slow flashing.
button
On the transmitter, simultaneously press and hold
the and buttons for approximately 5
seconds, until the LED comes on.
Release.
Check that the receiver's LED is no longer flashing.
The transmitter buttons
with the receiver.
Your unit comes with a plastic protection that must
be removed when work is complete (for example
after painting), before replacing the cover plate
(Delta Dore brand located in the lower right).
Plastic
protection
The receiver is compatible with:
incandescent lamps
lamps
(300 W), halogens with electronic transformers
(300 W) and 230V halogen lamps with TBT ferro-
magnetic transformer (300 W).
The receiver is incompatible with:
fluorescent lamps, motors and controlling hi-fi or
video products.
On the transmitter, press and hold the
for 5 seconds. The LED will light up, go out, then
light up again. Release.
Check that the receiver's LED is no longer flashing.
The transmitter
(TYXIA) or (TYDOM 200
the receiver in remote control switch mode.
To link a TYXIA 411 with a TYDOM 200, please
refer to the TYDOM 200 guide.
or
(status being modified)
button to pass from one

Simple lighting mode

Connection
button
Operating the TYXIA 411
Pressing the
(on or off).
Associating a
buttons
until the LED flashes
A button can control different receivers simulta-
neously (roller blinds, dimmer, simple lighting, etc.).
On the receiver, set the appliance to the required
status (e.g. light off), then press the receiver button
until the LED flashes (~3 seconds).
button to pass from one rate
2 possible choices.
Slow flashing: simple lighting mode
Rapid flashing: remote control switch mode (unused).
Press the receiver
of flashing to the other.
Select the slow flashing.
On the transmitter, press and hold the
down for approximately 5 seconds. The LED will light
up, go out, then light up again. Release.
and are associated
Check that the receiver's LED is no longer flashing.
The transmitter
receiver.
(1000 W), 230V halogen
(1000 W), low-consumption lamps
button
button is associated with
TYXIA 411
T L R N N
N 230 V
50 Hz
L
button changes the current state
button (scenario)
button to pass from one rate
button
button is associated with the