Summary of Contents for HuperLab Gaia404
- Page 1 SHINOBI Gaia404 / 408 / 416-60 / 416-120 Chassis Assembly Guide Version 1.0 Published August 2009 Copyright©2009 ASRock INC. All rights reserved. Copyright©2009 Huper Laboratories CO., LTD. All rights reserved. 1 1 1 1 1...
- Page 2 Copyright Notice: Copyright Notice: Copyright Notice: Copyright Notice: Copyright Notice: No part of this manual may be reproduced, transcribed, transmitted, or translated in any language, in any form or by any means without the written consent of hupeLab and ASRock Inc., except duplication of documentation by the purchaser for backup purpose.
-
Page 3: Table Of Contents
Contents Contents Contents Contents Contents I. Introduction I. Introduction I. Introduction ............I. Introduction I. Introduction ............................................4 4 4 4 4 I.1 Package Contents ............5 I.2 Recommended Tools ............5 I.3 Recommended Working Environment ......5 II. -
Page 4: Introduction
I. Introduction I. Introduction I. Introduction Thank you for purchasing huperLab Gaia404 / Gaia408 / Gaia416 motherboard, a reliable motherboard produced under huperLab’s consistently stringent quality control. It delivers excellent performance with robust design conforming to huperLab’s com- mitment to quality and endurance. -
Page 5: Package Contents
I.1 P I.1 P age Contents age Contents I.1 P I.1 P I.1 Pack ackage Contents age Contents age Contents Motherboard Accessories 4 x Screws (SCREW M3*5L (F) W-ZN #2) 1 x BNC Card Cable Chassis Accessories 20 x Screws (SCREW M3*12L (P) #2) Fan Module BNC Board... -
Page 6: Ii.1 Chassis Internal View
II. P II. P ar ar ar ar ar t One R II. P t One R t One R emoval of Chassis emoval of Chassis II. P II. P t One R t One R emoval of Chassis emoval of Chassis emoval of Chassis Components Components... -
Page 7: Ii.2 Removal Of Modules Inside Chassis
II.2 R II.2 R II.2 R II.2 R II.2 Removal of modules inside Chassis emoval of modules inside Chassis emoval of modules inside Chassis emoval of modules inside Chassis emoval of modules inside Chassis * Please make sure to disconnect power supply and peripherals before removing the system components. -
Page 8: Figure 4. Fan, Ssd Bracket, Hdd Bracket Removal
Step 3. Remove the fan module. Remove one flat screws securing the fan to the BNC board and two screws securing the fan to the cold-swap bay. See Figure 4. Step 4. Remove the SSD bracket by remove two screws securing the SSD bracket to the HDD cage. - Page 9 Step 5. Remove the front bezel by disconnect the cover hooks. Then, remove two screws securing the HDD bracket to the cold-swap bay. See Figure 4. *Move the cables around while removing the components. *Prevent the cables from rubbing each other. *This will harm the cables.
-
Page 10: Ii.3 Comparison
Step 6. Remove the BNC board. Remove six screws securing the BNC board to the chassis. Figure 6. BNC Board Removal III.3 Comparison III.3 Comparison III.3 Comparison III.3 Comparison III.3 Comparison Befor ore e e e e After After After After After Figure 7. -
Page 11: Iii.1 Motherboard Configuration
III. Motherboard Installation III. Motherboard Installation III. Motherboard Installation III. Motherboard Installation III. Motherboard Installation Gaia404 (A330GC-H4) / Gaia408 (A330GC-H8) / Gaia416-60 (A330GC-H16-60) / Gaia416-120 (A330GC-H16-120) huperVision 4000 DSS Server Board. III.1 Motherboard III.1 Motherboard Configuration III.1 Motherboard Configuration Configuration Configuration III.1 Motherboard... -
Page 12: Iii.2 Motherboard Installation
III.2 Motherboard III.2 Motherboard Installation Installation III.2 Motherboard III.2 Motherboard Installation III.2 Motherboard Installation Installation *Place screws into the holes indicated by circles to secure the motherboard to the chassis. *Do not over-tighten the screws! Doing so may damage the chassis and motherboard. -
Page 13: Figure 10. Connect Atx Psu
Step 2. Connect the ATX power connector from the ATX power supply to the motherboard. Figure 10. Connect ATX PSU Step 3. Install the BNC board to the motherboard. Insert the BNC card cable to video in (see P.11 No.6). Side Figure 11. -
Page 14: Figure 12. Cold-Swap, Ssd Bracket Installation
Step 4. Install the cold-swap bay. Gentally push half way of the cold swap bay into the HDD cage. Connect the SATA cable to the SATA II_2 connector(see P.11 No. 2) and connect the power connector from the ATX power supply on one side of the HDD cage. -
Page 15: Hardware Information & Installation
Hardware Information & Installation: 1.If your system includes the optional internal SSD hard drive, it is suggested to install the machine’s operating system on the SSD hard drive and store the video recording data on one or two hard drive. 2.If your system does not include the optional internal SSD hard drive and plan to install two hard drives, it is suggested to install the machine¡¦s operating system on the internal SATA hard drive... - Page 16 Step 6. Optional hard drive installation. Installing cold swap hard drive-- Insert the hard drive to the HDD bracket and fasten two screws on each side to secure the bracket to the cold swap bay. Installing internal SATA hard drive-- Fasten two screws on two side of the hard drive before insert the hard drive to the HDD cage.
-
Page 17: Figure 14. Fan Module Installation
Step 7. Install the fan module. Connect CPU fan to CPU fan connector and fasten one flat screws to secure the fan module to the BNC board and two screws to the cold-swap bay. See Figure 12. *Move the cables around while installing the components. *Prevent the cables from rubbing each other. -
Page 18: Figure 15. Front Bezel Installation
Step 8. Install the front bezel. Make sure all the hooks clicked. Figure 15. Front bezel installation Step 9. Install the chassis cover. Gentally slide the chassis cover toward the front bezel. Fasten three screws to secure the chassis cover to BNC board. Figure 16.
Need help?
Do you have a question about the Gaia404 and is the answer not in the manual?
Questions and answers