Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Summary of Contents for DAS DAS-M44HD-CI-CAN
- Page 2 Warnings: Important Safety Instructions and Caution Please read all of these instructions regarding your unit and retain them for future reference Read this manual fully and carefully before operating DAS digital receiver • Keep this manual handy as a reference for operating procedure and safety information •...
-
Page 3: Table Of Contents
DAS system analyzes and scans automatically the TV channels frequencies by eliminating the manual procedures normally used. DAS allows to get the best reception of the signal during a journey. Using the RDS system combined to digital signal (DVB-T), DAS changes automatically the frequency of the... - Page 4 PART NUMBERS DAS-M44HD-CI-CAN DCAB6P DCABRCA DRCV1 DTELSE DCABFO Multiconn Srl Pag. 4 of 23 DAS-M44HDCI -CAN- User Manual (EN)
- Page 5 Installation Install DAS DVB-T receiver with ALL 4 antennas. Connect the 4 antennas to the receiver before switching the unit on, but pay attention NOT TO FIX immediately the antennas on windows or any other inside part (provided it’s not metal) until you have found the proper location, as shielded glasses can strongly influence reception.
- Page 6 GPS, Amplifier, etc…) and match it directly to the female connector of the fiber optic cable on equipment (F1). Then match the two other connector F2 and F3 respectively inside the DAS receiver (see picture) and to the original fiber optic accessory of the vehicle.
- Page 7 For the VIDEO connections make reference to the installation manuals for specific Auto-maker and model of car available at the following link http://www.dasdvbt.com/ita/software.php IR Infrared receiver for remote control M44HD-CI–CAN – signal side Multiconn Srl Pag. 7 of 23 DAS-M44HDCI -CAN- User Manual (EN)
-
Page 8: Remote Control Operations
1) Turn the remote control face down. 2) Press down on the ridged area of the battery cover and slide it off 3) Slide another battery in (mod.CR2025 o CR2032) Multiconn Srl Pag. 8 of 23 DAS-M44HDCI -CAN- User Manual (EN) -
Page 9: Start And Antennas Installation
DAS is a receiver with 4 antennas, 3 assigned to the reception of the TV channels and 1 assigned to the autoscan and to the update in real time of the dynamic “TV list”. - Page 10 • Install each antenna taking care of the level signal of the bar. To exit from antenna menu push OK / Menu Multiconn Srl Pag. 10 of 23 DAS-M44HDCI -CAN- User Manual (EN)
-
Page 11: Settings Configuration Menu
To exit from configuration menu push OK/Menu button or Languages • Select the language Screen • Select the screen in 4/3 or 16/9 Video output • Select if the video is in PAL or NTSC Multiconn Srl Pag. 11 of 23 DAS-M44HDCI -CAN- User Manual (EN) - Page 12 This is an essential feature to update automatically the “TV list”. Selecting this option, when the vehicle is turned-off or when the receiver is in stand-by, DAS is ON and it will use the 4 antennas in autoscan version to scan the frequencies and automatically update all TV channels inside the “TV list”.
-
Page 13: Antennas Status And Check
• If the 4 bars are similar, this means that the antennas are working correctly • If 1 or more bars are significantly scarce, this means that the antennas have deteriorated and need to be replaced Multiconn Srl Pag. 13 of 23 DAS-M44HDCI -CAN- User Manual (EN) -
Page 14: Tv List And Memo Tv Channels List
TV List and Memo TV Channel List DAS system allows to get 2 different TV lists: 1. The “TV List” is controlled directly by antenna no. 1. This list is automatically updated in real time and it works like frequency auto scan. -
Page 15: Memorize Tv Channels
Memorize TV Channel DAS system is the real heart of auto-scan technology: the searching of the TV channels and the related frequencies is made automatically and no manual intervention is needed. The storage /memorization of the TV channels is essential to ensure the best performance of the receiver. - Page 16 • If the “TV channel bars” has been selected, the TV channel appears also at position no.5 of the TV channel bar showed on the screen. • Repeat this procedure to store all the other TV channels. Multiconn Srl Pag. 16 of 23 DAS-M44HDCI -CAN- User Manual (EN)
-
Page 17: Change Tv Channel
This notice can be disabled from the configuration menu. Zapping While viewing a TV channel, to have a quick zapping, simply press to display the next or previous channel to the current channel you are watching. Multiconn Srl Pag. 17 of 23 DAS-M44HDCI -CAN- User Manual (EN) -
Page 18: Upgrade Via Usb - Pag.18
• Check the SW on the receiver using the function "menu 123" • On Top it shows "DAS rev. 0.xxx " • Check if the revision number is the same as that one shown online. • If it is not the same, download the latest SW (present in a compressed mode) and copy on a USB stick (FAT32 formatted) after decompressed –... - Page 19 • Insert the CAM and CARD slot in the receiver, • Wait and verify the correct operation of the Pay TV by selecting the pay channels in the "TV List". Multiconn Srl Pag. 19 of 23 DAS-M44HDCI -CAN- User Manual (EN)
-
Page 20: Trouble Shooting Q & A
No power Check the remote battery The unit does not respond to remote Unit damaged. control commands Power supply cut during upgrade To be returned to assistance desk Multiconn Srl Pag. 20 of 23 DAS-M44HDCI -CAN- User Manual (EN) - Page 21 CI option. Only the locally free TV channels Some TV channels are not available can be seen. They can differ depending on the area. Refer to manual at pag.15 Multiconn Srl Pag. 21 of 23 DAS-M44HDCI -CAN- User Manual (EN)
- Page 22 The quality of the picture Tolerances of electronic components Change the screen or take is white and black and between DAS product and the screen another DAS tuner. not coloured The yellow wire must have always The DAS tuner doesn’t The 12V of the battery is missing on the +12V;...
- Page 23 Incorrect configuration of the CAM TV channel from TV list If problem persists, please contact the dealer where you bought the unit for assistance. Multiconn Srl Pag. 23 of 23 DAS-M44HDCI -CAN- User Manual (EN)