Table of Contents
Advertisement
Quick Links
Installation Instructions
Please Leave for Occupant
1
2
3
4
5
6
Description
The GRX-CIR receives signals from the GRAFIK
Eye GRX-IT or GRX-8IT Handheld Wireless
Remote Control to activate scenes on the
GRAFIK Eye 3000 or 4000 Control Unit. It
requires an unobstructed line-of-sight for
receiving the signal (Remote Control pointed
directly at the GRX-CIR's receiver). The GRX-
CIR offers 360˚ activation and a range of up to
50 feet (15 m).
READ ALL INSTRUCTIONS CAREFULLY
BEFORE STARTING INSTALLATION!
CAUTION!
DIP Switches
Install in accordance with all applicable
regulations.
The GRX-CIR is a Class 2/PELV control; do
Infrared
not connect line-voltage/mains cable to
Lens
Class 2/PELV terminals. Improper wiring can
result in personal injury or damage to the
control or to other equipment.
Programming
GRAFIK Eye Wallstations must be connected
LED
to the GRAFIK Eye Control Unit by using
Class 2/PELV wiring methods per the
National Electrical Code. Check with your
local electrical inspector for the local code
requirements and wiring practices allowed in
your area.
GRX-CIR Wallstation
Ceiling-mounted Infrared Receiver
Class 2/PELV
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Summary of Contents for Grafik Eye GRX-CIR Wallstation
- Page 1 Programming GRAFIK Eye Wallstations must be connected to the GRAFIK Eye Control Unit by using Class 2/PELV wiring methods per the Description National Electrical Code. Check with your...
- Page 2 Wiring Notes Proper wiring of Wallstations is dependent upon the GRAFIK Eye Control System that is providing power. GRAFIK Eye 3000 Series and GRAFIK Eye 4000 Series Control Units have different power limitations and wiring techniques. Please confirm the type of Control Unit to which the Wallstation is being wired and use the corresponding instructions.
- Page 3 2.2 in. (55.9 mm) 4. Address the Control Units. To assign 2.2 in. (55.9 mm) addresses to the GRAFIK Eye 3000 or 4000 Control Units, see the Instructions shipped with each Unit. 5. Address the GRX-CIR. Each GRX-CIR in a 2.
- Page 4 For this Address: 7. Strip insulation from wires so that 3/8 in. Set switches Set switches (10 mm) of bare wire is exposed. like this: like this: 8. Wiring must be done in a daisy-chain and 1-to-1 configuration (please see Installer's Location Location 1 2 3 4...
- Page 5 3000 Series Control Unit 4: BLUE 3: YELLOW 2: RED 1: WHITE/BLACK CLASS 2/PELV WIRING 4: MUX 2: 12 DC 3: MUX 1: COMMON DATA LINK: 4000 Series Control Unit 4: MUX 3: MUX 4: BLUE 2 IN, OUT 3: YELLOW 1 IN, OUT 2: RED 1: WHITE/BLACK...
- Page 6 System Communications In order for the GRX-CIR to communicate with a Control Unit, each GRX-CIR must be individually configured to “talk” by putting the GRX-CIR in setup mode (only one GRX-CIR can be in setup mode at a time). The GRX-CIR can be put into setup mode only by using a GRX-IT or GRX-8IT Handheld Wireless Remote Control.
- Page 7 Miswire. Confirm all connections. Correct swapped wires in daisy- chain. Connect all wires in multicontrol chain. GRAFIK Eye Control Address GRAFIK Eye Control Units. Units do not have addresses. GRX-CIR does not work. Miswire. Confirm all connections. GRAFIK Eye Control...
- Page 8 International 49 309 710-4591 exact specifications, and suitability for your application. Lutron and GRAFIK Eye are registered trademarks of Lutron Electronics Co., Inc. © 1999 Lutron Electronics Co., Inc. Lutron Electronics Co., Inc. Made and printed in U.S.A.
Need help?
Do you have a question about the GRX-CIR Wallstation and is the answer not in the manual?
Questions and answers