Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Summary of Contents for IED Globalcom IEDA520
- Page 1 INSTALLATION INSTRUCTIONS IEDA520 / LC108 DIGITAL COMMUNICATION STATION IEDA520 / LC108MS IEDA520D IEDA520D-G IEDA520W IEDA520W-T IEDA520W-H IEDA520DTB LC108MS-D LC108MSD-G LC108MSW-HS LC108MSW-HH DIGITAL COMMUNICATION STATION Installation Instructions REV: 01-12 DOC: 369B...
- Page 2 INSTALLATION INSTRUCTIONS IEDA520 / LC108 DIGITAL COMMUNICATION STATION INTRODUCTION Description The IED 520 Series Digital Communication Station is a user communication device for initiating audio/visual an- nouncements, messages, and pages with the 500, 505, and 510 Announcement Control Systems. It is a network appliance with its own unique IP address, which simplifies its installation and configuration.
-
Page 3: Network Requirements
IEDA520 / LC108 DIGITAL COMMUNICATION STATION INSTALLATION INSTRUCTIONS from the pass-through connection and into the paging system whenever the user makes an announcement go active by pressing the PTT switch. The wall mount version of the 520 digital communication station can be equipped with either a telephone style handset, or with the IED 501HH teardrop handheld microphone. -
Page 4: Important Safety Instructions
INSTALLATION INSTRUCTIONS IEDA520 / LC108 DIGITAL COMMUNICATION STATION IMPORTANT SAFETY INSTRUCTIONS SAFETY SYMBOLS Read these instructions. Keep these instructions. Heed all warnings. Labeling on products and the Installation Instructions & Follow all instructions. User Manual may use safety related graphical symbols Do not use this apparatus near water. - Page 5 IEDA520 / LC108 DIGITAL COMMUNICATION STATION INSTALLATION INSTRUCTIONS CONNECTIONS IEDA520D / LC108MS-D Base Unit Status LED Telephone Pass- Solid amber indicates Through 100BaseT link Traffic LED Flashes green with network activity Handset/Headset RJ45 Ethernet Input XLR for Gooseneck mic Pin 1 = S Pin 2 = + Pin 3 = –...
- Page 6 INSTALLATION INSTRUCTIONS IEDA520 / LC108 DIGITAL COMMUNICATION STATION IEDA520W-H / LC108MSW-HH The front panel controls between the desktop and wall-mount base units are identical. This illustration highlights the connection differences between the two units. Note that the telephone handset/headset interface is only available in the desktop base units and not in the wall-mount units.
- Page 7 IEDA520 / LC108 DIGITAL COMMUNICATION STATION INSTALLATION INSTRUCTIONS IEDA520W-T / LC108MSW-HS The IEDA520HS handset has a different output signal level from the IEDA501HH. Thus, it must be connected a dedicated handset input located inside the unit. Due to this difference, the IEDA520HS ships attached to the base unit.
-
Page 8: Installation
INSTALLATION INSTRUCTIONS IEDA520 / LC108 DIGITAL COMMUNICATION STATION INSTALLATION IEDA520W Base Unit Attached to IEDA520DTB Desktop Base IEDA520DTB IEDA520W Base Unit Attached to Standard Electrical Box Standard 1-gang electrical box REV: 01-12 DOC: 369B PAGE 7... -
Page 9: Configuration Examples
IEDA520 / LC108 DIGITAL COMMUNICATION STATION INSTALLATION INSTRUCTIONS CONFIGURATION EXAMPLES Configuration for Dynamic Gooseneck Microphone IEDA520D / LC108MSD Base No Connection PoE Ethernet to port Parameter Setting Mic Type Gooseneck Gooseneck/Handset 20dB boost Enable Telephone Passthrough Enable Sidetone Hand/Headset Power... - Page 10 INSTALLATION INSTRUCTIONS IEDA520 / LC108 DIGITAL COMMUNICATION STATION Configuration using IEDA501HH Hand-Held microphone IEDA520W / LC108MSW Base Only PoE Ethernet to port on back of unit Parameter Setting Mic Type Handheld Gooseneck/Handset 20dB boost Enable Telephone Passthrough Enable Sidetone Hand/Headset Power...
- Page 11 Hand/Headset Power CONFIGURATION All confuguration options for the IEDA520/LC108MS must be performed using the IED520 Configuration Utility. This utility is typically available as a stand-alone application on the system server desktop and is often placed in the Application Bar for systems that utilize this feature. Figure 1 shows the icon for the configuration utility application.
-
Page 12: Setting A New Ip Address
INSTALLATION INSTRUCTIONS IEDA520 / LC108 DIGITAL COMMUNICATION STATION 2. Place fingers and hold simultaneously on the + and – buttons for approximately three (3) seconds to place the mic station in configuration mode. The unit will respond with one (1) beep followed by both the red and green LEDs flashing in a repeating pattern that consistes of two quick flashes followed by a slight pause. - Page 13 IEDA520 / LC108 DIGITAL COMMUNICATION STATION INSTALLATION INSTRUCTIONS Configuration Utility Reference Figure 2 - IED520 Configuration Utility Current IP Address Type in the IP address of the unit in this entry box. This is the address that the application will attempt to connect to once the Connect button is pressed.
- Page 14 INSTALLATION INSTRUCTIONS IEDA520 / LC108 DIGITAL COMMUNICATION STATION Set New Address Click this button to send the new address settings to the unit. Once the settings have been applied, the new IP address will be shown in Current IP Address box. Click the Connect button to refresh the settings from the unit at the new IP address.
- Page 15 IEDA520 / LC108 DIGITAL COMMUNICATION STATION INSTALLATION INSTRUCTIONS Earpiece Volume (dB): This volume control will increase or decrease the audio level at the earpiece when the station is used as an intercom unit. It will not adjust the sidetone level when the sidetone option is enabled and it will not adjust the earpiece level when the handset or headset is used with the telephone base unit through the loop-through port.
- Page 16 INSTALLATION INSTRUCTIONS IEDA520 / LC108 DIGITAL COMMUNICATION STATION Innovative Electronic Designs, LLC +1.502.267.7436 phone 9701 Taylorsville Road +1.502.267.9070 fax Louisville, KY 40299, USA www.iedaudio.com REV: 01-12 DOC: 369B ©2012, Innovative Electronic Designs, LLC...