HAI 54A00-1 Manual

Access control keypad

Download this manual

DESCRIPTION

The Model 54A00-1 HAI Access Control Keypad is a weatherproof and vandal resistant piezoelectric keypad designed to interface

with the HAI line of automation controllers. Each valid code can be used to arm and disarm the security system, activate an electric

door strike or magnetic locks, activate lighting, operate a garage door, operate a security gate, set off a panic alarm, and many other

functions.

The keypad is encased in a stainless steel investment casting that will complement any décor. It mounts in a single gang switchbox or

to the surface of any wall indoors or outdoors. The keypad has a red LED that is illuminated when the security system is armed and a

green LED that is illuminated when it is disarmed.

INSTALLATION

The Model 54A00-1 requires the use of one serial port on the controller and one programmable voltage output. Multiple keypads may

be connected in parallel as shown in Figure 1.

Run a 4-conductor cable from the controller to the location of the Model 54A00-1 Access Control Keypad and install as follows:

1. At the keypad location, using the supplied B-GEL water-tight wire splice connectors, connect the black, red, white, and

brown wires of the keypad cable (P/N: 54A03-1) to the corresponding wires of the 4-conductor cable as follows:

Keypad Cable (P/N: 54A03-1)

Black

Red

White

Brown

2. Insert the keypad cable into the connector on the back of the keypad.

3. Install the 54A00-1 to the surface of any wall using the supplied wall anchors and screws or to a single gang switchbox using

the supplied machine screws.

4. Adhere the top (with LED cutouts) and bottom (with HAI logo to bottom right) overlay to the 54A00-1 by removing the

backing and pressing into place.

5. At the controller location, connect the black, red, green, and yellow wires of the keypad communications cable

(P/N: 54A02-1) to the corresponding wires of the 4-conductor cable using the supplied wire splice connectors as shown.

6. Connect the green wire of the keypad communications cable (P/N: 54A02-1) to one of the programmable voltage outputs on

the controller as shown. Configure the voltage output as an "Armed" output

7. Connect the red wire of the keypad communications cable (P/N: 54A02-1) to the Auxiliary 12V output on the controller as

shown.

8. Insert the modular connector of the keypad communications cable (P/N: 54A02-1) into one of the serial ports on the

controller as shown. Configure the serial port to Pro-Link.

Home Automation, Inc.

Model 54A00-1 HAI Access Control Keypad

4-Conductor Cable

Black

Red

Yellow

Green

(Connections Diagram on Next Page)

Page 1 2. Insert the keypad cable into the connector on the back of the keypad. 3. Install the 54A00-1 to the surface of any wall using the supplied wall anchors and screws or to a single gang switchbox using the supplied machine screws.
Page 2 GREEN 54A02-1 54A03-1 BROWN WHITE BLACK 54A03-1 FIGURE 1 – MODEL 54A00-1 CONNECTIONS Page 2...
Page 3 If there is a 10 second delay between entering digits, the keypad will cancel previously entered digits. When a previously entered code has been canceled, either by pressing the ‘*’ key or when there has been a 10 second delay, the 54A00-1 will emit two short tones and flash the red LED two times.
Page 4 WHEN Door Strike OFF: Red LED OFF Every time “1 2 3 4 1 #” is entered at the 54A00-1, the output will turn on to disengage the electric door strike for the specified amount of time (i.e. 5 seconds). The red LED will illuminate whenever the door strike is disengaged (unlocked) and the green LED will illuminate whenever the door strike is engaged (locked).