Page 1 • Keep this manual in a safe place where you can refer to it easily while installing, operating, and carrying out maintenance or inspections. Omni-4000ST User’s Manual...
Page 2 ISHIDA. No patent liability is assumed with respect to the use of the information contained herein. Moreover, because ISHIDA is constantly striving to improve its high-quality products, the information contained in this manual is subject to change without notice.
Page 3 ISHIDA is not liable for any damage, loss or injury that results from incorrect operation, insufficient caution, unauthorized modifications to the machine, or failure to follow the instructions contained in this manual.
Page 4 This sticker indicates that the maximum load at This sticker indicates that there is a danger of full extension should not exceed 10 lbs. on the electric shock on the power supply unit cover. in-feed conveyer cover. page ii Omni-4000ST User’s Manual...
Page 5 Otherwise, your hand may get caught in the film roller. DO NOT TOUCH, OR ALLOW CLOTHING TO TOUCH THE HEATER CONVEYER. The heater conveyer will remain hot for some time even after the power is switched OFF, and can cause burns if touched. Omni-4000ST User’s Manual page iii...
Page 6: Installation Precautions
A power supply that generates voltage variation may cause a malfunction. • Do not stand on the power cord, and do not place anything heavy on the cord. Doing so may damage the cord, resulting in accident or trouble. page iv Omni-4000ST User’s Manual...
Page 7 • Always ensure that the machine is level. If the level is not centered, weighing will not be accurate and wrapping will not be performed well. Adjust the level adjusting feet until the bubble inside the level indicator is centered. Omni-4000ST User’s Manual page v...
Page 8 Installation Space Precautions Allow ample space on either side of the machine and behind the machine to ensure easy access for maintenance. page vi Omni-4000ST User’s Manual...
Page 9: Table Of Contents
2.12 CHECKING PRINT ITEMS FOR LABELING ..... 2-21 2.13 MEMO PRESET BUTTON ..........2-22 2.14 FUNCTION KEYS .............. 2-26 CHAPTER 3 TOTAL MODE TOTAL MENU............... 3-2 DAILY / ACCUMULATED TOTAL ......... 3-3 HOURLY + TRAY TOTALS........... 3-9 TOTAL CLEAR ..............3-15 Omni-4000ST User’s Manual page vii...
Page 10 4.12 TEXT EDITING..............4-37 CHAPTER 5 SETUP MODE STARTING PROCEDURE ........... 5-2 SETUP MENU..............5-3 EXPIRY DATE SETTING ............. 5-4 PASSWORD SETTING ............5-6 WORD-WRAP WIDTH SETTING......... 5-7 REFERENCE DATA SETUP ..........5-8 TOTAL ADD SETTING ............5-11 page viii Omni-4000ST User’s Manual...
Page 11 1.3 LABELS, TRAYS, AND FILM ........1-4 1.4 OPERATION START / END .......... 1-6 1.5 EMERGENCY STOP ON/OFF ........1-7 1.6 FILM ROLL LOADING ..........1-8 1.7 FILM THEADING............1-9 1.8 LABEL SETTING ............1-12 1.9 DAILY MAINTENANCE..........1-16 Omni-4000ST User’s Manual page 1-1...
Page 12: Chapter 1 Before Using This Machine
Chapter 1 BEFORE USING THIS MACHINE 1.1 NAME OF EACH PART page 1-2 Omni-4000ST User’s Manual...
Page 13: Stroke Keys
Chapter 1 BEFORE USING THIS MACHINE 1.2 STROKE KEYS Omni-4000ST User’s Manual page 1-3...
Page 14: Labels, Trays, And Film
Unusable trays Following trays cannot be used. Fragile trays Deformed trays Round or hollow-bottomed trays Trays made of transparent Dark blue trays Trays other than square and materials rectangular trays page 1-4 Omni-4000ST User’s Manual...
Page 15 Lopsided contents Overfilled tray 1.3.3 FILM TYPE Use the film designated by ISHIDA, as packing may not be performed if other films are used. Contact your ISHIDA service representative for further details regarding usable films. Omni-4000ST User’s Manual page 1-5...
Page 16: Operation Start / End
Weigh Platter or in the Do not touch the wrapping area and turn OFF the Heater Conveyer, as it Main Power Switch . remains very hot even after the Main Power Switch is turned OFF. page 1-6 Omni-4000ST User’s Manual...
Page 17: Emergency Stop On/Off
Chapter 1 BEFORE USING THIS MACHINE 1.5 EMERGENCY STOP ON/OFF 1.5.1 EMERGENCY STOP ON Press the Emergency Stop button. 1.5.2 EMERGENCY STOP OFF Turn the Emergency Stop button clockwise to release. Omni-4000ST User’s Manual page 1-7...
Page 18: Film Roll Loading
Film core film on the film position decal. Turn the lever vertical to the film Lever core to secure the film roll position. Film core Close the Film Replacement Door. page 1-8 Omni-4000ST User’s Manual...
Page 19: Film Theading
Open the Side Cover, and use the handle to lift up the Film Set Roller until it locks into position. Open the Side Door. Evenly cut the top edge of the film, and pull it up. Omni-4000ST User’s Manual page 1-9...
Page 20 Stick the film on both Film Feed Belts. Use the handle to slightly lift up to release the lock condition and lower the Film Set Roller. Lower the Side Cover. Close the side door. page 1-10 Omni-4000ST User’s Manual...
Page 21 Make sure that the Emergency Stop button has been pressed before removing the film. Unless the Emergency Stop button is pressed, the film cannot be removed because it is pinched by clamps. Release the Emergency Stop button Omni-4000ST User’s Manual page 1-11...
Page 22: Label Setting
Emergency Stop button has been pressed before opening the Printer Cover. If the Applicator is positioned in front of the printer, move the Applicator to the side. Use the lever to open the print head. page 1-12 Omni-4000ST User’s Manual...
Page 23 Set a label roll around the holder and thread the label paper as shown in the figure. Set the end of backing paper with the stopper and turn the Label Take-up Bobbin counterclockwise until the label slack is taken up. Omni-4000ST User’s Manual page 1-13...
Page 24 Chapter 1 BEFORE USING THIS MACHINE Lock the Label Roll Stopper. Slide the printer back to its original position. Close the Print Head. Release the Emergency Stop button page 1-14 Omni-4000ST User’s Manual...
Page 25 Chapter 1 BEFORE USING THIS MACHINE Press the [FEED] key several times to make sure that labels are normally issued. Close the Printer Cover. Omni-4000ST User’s Manual page 1-15...
Page 26: Daily Maintenance
Do not apply water directly as it can damage the machine. • Lubricating each drive unit is not necessary. • 1.9.1 MACHINE CLEANING Press the [ ] button on the screen. Press the [PREPARE CLEAN] button on the screen. page 1-16 Omni-4000ST User’s Manual...
Page 27 Turn OFF the Main Power Switch. The Heater Conveyer remains hot even after the Main Power Switch has been turned OFF. Avoid touching the conveyer as you may burn yourself. Open the Printer Cover. Omni-4000ST User’s Manual page 1-17...
Page 28 Chapter 1 BEFORE USING THIS MACHINE 1.9.2 PLACES TO BE CLEANED page 1-18 Omni-4000ST User’s Manual...
Page 29: Chapter 2 Normal Mode
2.9 MARKDOWN PRICE........... 2-14 2.10 MANUAL LABELING ..........2-16 2.11 DATE AND TIME CHANGE ........2-18 2.12 CHECKING PRINT ITEMS FOR LABELING ....2-21 2.13 MEMO PRESET BUTTON .......... 2-22 2.14 FUNCTION KEYS ............2-26 Omni-4000ST User’s Manual page 2-1...
Page 30: Screens In Normal Mode
Also displays the tray list screen when touched without numeric entry. screen. touched without numeric entry. Changes the data when pressed after numeric entry. Also displays the print selection screen when touched without numeric entry. page 2-2 Omni-4000ST User’s Manual...
Page 31 Chapter 2 NORMAL MODE 2.1.2 EXAMPLE OF WEIGHING PLU SCREEN 2.1.3 EXAMPLE OF FIXED PRICE PLU SCREEN Displays the upper/lower weight limit setting screen when pressed. Omni-4000ST User’s Manual page 2-3...
Page 32: Plu Call Up
Pressing the panel using pointed objects EXAMPLE such as fingernails or Call up PLU No.131. mechanical pencils may damage the touch panel. . The designated PLU screen is displayed. page 2-4 Omni-4000ST User’s Manual...
Page 33 “BEEF”. may damage the touch panel. The Category Preset List screen is displayed. Press the [Select Beef BNLS Shoulder Steak] field to make a selection. . The designated PLU screen is displayed. Omni-4000ST User’s Manual page 2-5...
Page 34 Use the [ ] and [ ] buttons to turn over the screen until you find the desired PLU and press the desired field to make a selection.. EXAMPLE Call the “Select Beef BNLS Shoulder Steak”. page 2-6 Omni-4000ST User’s Manual...
Page 35 BEEF Press the desired Memo Preset button to make a selection. EXAMPLE Call the “SLICED BEEF” using 000004 000005 000006 000007 Memo Preset button. OREGON CALIFORNIA UTAH SLICED GROUND GROUND GROUND BEEF BEEF BEEF BEEF Omni-4000ST User’s Manual page 2-7...
Page 36: Weighing / Wrapping / Labeling
Weigh Platter. after placing it on the Weigh Platter. The tray is weighed, wrapped, Otherwise your hand may get caught in the labeled, and discharged. In-feed Pusher that moves automatically immediately after the tray is placed. page 2-8 Omni-4000ST User’s Manual...
Page 37: Wrapping Only
Do not touch the tray Weigh Platter. after placing it on the Weigh Platter. The tray is wrapped and Otherwise your hand discharged. may get caught in the In-feed Pusher that moves automatically immediately after the tray is placed. Omni-4000ST User’s Manual page 2-9...
Page 38: Labeling Only
Do not touch the tray Weigh Platter. after placing it on the Weigh Platter. The label is issued. Otherwise your hand may get caught in the In-feed Pusher that moves automatically immediately after the tray is placed. page 2-10 Omni-4000ST User’s Manual...
Page 39: Tentaive Unit Price Change
Make sure that the desired PLU screen is displayed. Enter a new unit price using numeric keys and press the [U/P] stroke key. The unit price has been changed to the new unit price tentatively. Omni-4000ST User’s Manual page 2-11...
Page 40: Tentative Change To Fixed Price
Change the unit price $6.29 to the fixed price $7.00 tentatively. Make sure that the desired PLU screen is displayed. Enter the fixed price using numeric keys and press the [FIX] stroke key. The unit price has been changed to the new fixed price tentatively. page 2-12 Omni-4000ST User’s Manual...
Page 41: Tray Change
. The Tray Name List screen is displayed. . Press the desired field to select the tray number to be used. The display automatically returns to the PLU screen, and the tray to be used has been tentatively changed. Omni-4000ST User’s Manual page 2-13...
Page 42: Markdown Price
Lightly press the touch panel with your finger. Pressing the panel using pointed objects such as fingernails or mechanical pencils may damage the touch panel. . The Markdown Price Mode Setting screen is displayed. page 2-14 Omni-4000ST User’s Manual...
Page 43 Pressing this button after numeric entry will register the discount unit price in the unit price field. Unit Price Percent Discount Pressing this button after numeric entry will register the discount unit price rate in the unit price field. Omni-4000ST User’s Manual page 2-15...
Page 44: Manual Labeling
. Press the [AUTO LABELING] button to change the button [AUTO LABELING] is display to [MANUAL LABELING]. usually displayed. The button display will change between [AUTO LABELING] and [MANUAL LABELING] each time the button is pressed. page 2-16 Omni-4000ST User’s Manual...
Page 45 The tray is weighed, wrapped, Otherwise your hand may get caught in the and discharged. In-feed Pusher that moves automatically immediately after the tray is placed. . Press the [FEED] stroke key to issue the label. Omni-4000ST User’s Manual page 2-17...
Page 46: Date And Time Change
[SHELF LIFE] field on the Lightly press the touch screen. panel with your finger. Pressing the panel using pointed objects such as fingernails or mechanical pencils may damage the touch panel. . The Pack Date Setting screen is displayed. page 2-18 Omni-4000ST User’s Manual...
Page 47 Press one of the following buttons. Select for printing the current time. Select for printing a certain time. (4) Sell-By Date Press one of the following buttons. Do not print the Sell-By Date. Print the Sell-By Date. Omni-4000ST User’s Manual page 2-19...
Page 48 9999 days) for Sell-By Date.. (7) Use By Enter the number of days (1 - 9999 hours) for Sell-By Date. Press one of the following buttons. Print the Pack Date. Do not print the Pack Date. page 2-20 Omni-4000ST User’s Manual...
Page 49: Checking Print Items For Labeling
When the field is pressed without numeric entry, displays the list for each item. Press the [BACK] button when additions and corrections are completed. The display returns to the initial screen. Omni-4000ST User’s Manual page 2-21...
Page 50: Memo Preset Button
SLICED SLICED Changes the mode. BEEF TEXAS OREGON SPECIAL BEEF BEEF Aborts respective operation mode and returns to the normal display. Executes each mode operation and returns to Truncates the PLU name. the normal display. page 2-22 Omni-4000ST User’s Manual...
Page 51 Preset button is The PLU data has been pressed. registered in the button. The display returns to the PLU screen. Registration can also be performed by pressing the [Memo Preset] button after entering the PLU number. Omni-4000ST User’s Manual page 2-23...
Page 52 Preset Delete mode. Press the desired memo preset to be deleted. 000004 000005 000006 000007 OREGON CALIFORNIA UTAH SLICED GROUND GROUND GROUND BEEF BEEF BEEF BEEF EXAMPLE Delete the ““UTAH GROUND BEEF” Memo Preset button. page 2-24 Omni-4000ST User’s Manual...
Page 53 Chapter 2 NORMAL MODE Press the [CONFIRM] button. The deletion has been executed and the display returns to the normal screen. Omni-4000ST User’s Manual page 2-25...
Page 54: Function Keys
This machine has many convenient function keys. Main function keys are located at the bottom of the screen, and sub function keys on the Function Key screen. Numeric function keys Displays the Function keys Function Key screen Function keys page 2-26 Omni-4000ST User’s Manual...
Page 55 Chapter 2 NORMAL MODE FUNCTION KEYS Omni-4000ST User’s Manual page 2-27...
Page 56 Chapter 2 NORMAL MODE page 2-28 Omni-4000ST User’s Manual...
Page 57 Chapter 2 NORMAL MODE Omni-4000ST User’s Manual page 2-29...
Page 58 -Front format number can be set when pressed after numeric entry. -To delete the setting, press the button after entering “0”. -Image number can be set when pressed after numeric entry. -To delete the setting, press the button after entering “0”. page 2-30 Omni-4000ST User’s Manual...
Page 59: Chapter 3 Total Mode
Chapter 3 TOTAL MODE TOTAL MODE CONTENTS 3.1 TOTAL MENU..............3-2 3.2 DAILY / ACCUMULATED TOTAL ........ 3-3 3.3 HOURLY + TRAY TOTALS .......... 3-9 3.4 TOTAL CLEAR ............3-15 Omni-4000ST User’s Manual page 3-1...
Page 60: Total Menu
Main Menu screen is displayed. Press the [TOTALS] button. If a password has been set for entering Total Mode, press the [TOTALS] button after password entry (6 digits). Total Menu screen is displayed. page 3-2 Omni-4000ST User’s Manual...
Page 61: Daily / Accumulated Total
Daily Total Menu screen is displayed. Press the [Daily Grand Total] button to select the desired report type. The Daily Grand Total screen is displayed. Omni-4000ST User’s Manual page 3-3...
Page 62 Daily Total Menu screen is displayed. Press the [Sales per Department] button to select the desired report type. The Sales per Department Total screen is displayed. page 3-4 Omni-4000ST User’s Manual...
Page 63 Daily Total Menu screen is displayed. Press the [Sales by PLU] button to select the desired report type. The Sales by PLU Total screen is displayed. Omni-4000ST User’s Manual page 3-5...
Page 64 Analysis By PLU screen is displayed. Set the number of items to be displayed by pressing [SET] in the Enter Report Size field after numeric entry. Note: Enter “0” to display all items and totalize them. page 3-6 Omni-4000ST User’s Manual...
Page 65 Displays and totalizes data in price ascending order. Displays and totalizes data in weight ascending order. Displays and totalizes data in quantity ascending order. Press the [DETAIL] button on the screen. The display changes to the Analysis By PLU screen. Omni-4000ST User’s Manual page 3-7...
Page 66 SLICE TEXAS BEEF 6.110 183.30 SLICE OREGON BEEF 3.604 108.12 Changes the screen for each classification type set on the Analysis BY PLU screen. This is not usable when the classification type is set as “No Analysis”. page 3-8 Omni-4000ST User’s Manual...
Page 67: Hourly + Tray Totals
Chapter 3 TOTAL MODE 3.3 HOURLY + TRAY TOTALS This section explains about how to obtain hourly and tray totals in this machine. Omni-4000ST User’s Manual page 3-9...
Page 68 The Hourly + Tray Totals screen is displayed. Press the [HOURLY TOTALS] button on the screen. Totals for each time zone screen 10.4 are displayed. 16.5 17.5 12.3 11.7 Select the type of data to be analyzed. page 3-10 Omni-4000ST User’s Manual...
Page 69 The Hourly PLU Totals screen is H O U R L Y P L U T O T A L S displayed. 0.000 0.00 Call the desired PLU by pressing the [PLU] stroke key after numeric entry. Omni-4000ST User’s Manual page 3-11...
Page 70 Totals for each time zone screen H O U R L Y P L U T O T A L S are displayed. GROUND BEEF 55.120 397.29 Select the type of data to be analyzed. 13.9 18.7 29.0 15.7 page 3-12 Omni-4000ST User’s Manual...
Page 71 Press the [HOURLY + TRAY TOTALS] button on the Total Menu screen. The Hourly + Tray Totals screen is displayed. Press the [HOURLY WRAP TOTALS] button to make a selection. Totals for each time zone screen are displayed. Omni-4000ST User’s Manual page 3-13...
Page 72 Press the [HOURLY + TRAY TOTALS] button on the Total Menu screen. The Hourly + Tray Totals screen is displayed. Press the [WRAP TOTALS BY TRAY] button to make a selection. Wrap Totals by Tray are displayed. page 3-14 Omni-4000ST User’s Manual...
Page 73: Total Clear
[DAILY] [TOTAL] [TIME ZONE] [TRAY TOTAL] and [PERIOD]. Press the [EXECUTE] button to clear the selected total. Delete confirmation screen is displayed. Press [EXECUTE] to clear the selected items. Omni-4000ST User’s Manual page 3-15...
Page 74 Chapter 3 TOTAL MODE page 3-16 Omni-4000ST User’s Manual...
Page 75: Chapter 4 Programming Mode
4.6 COUPON MESSAGE REGISTRATION....4-21 4.7 STORE NAME/ADDRESS REGISTRATION .... 4-23 4.8 TRAY MESSAGE REGISTRATION......4-26 4.9 DEPARTMENT NAME REGISTRATION ....4-32 4.10 CATEGORY PRESET REGISTRATION....4-34 4.11 PLU PRESET REGISTRATION ........ 4-36 4.12 TEXT EDITING............4-37 Omni-4000ST User’s Manual page 4-1...
Page 76: Contents
GROUP The group name can be registered. PRESET KEYS The PLU data can be allocated to the memory preset key CATEGORY PRESET The PLU data indexed and linked to the category preset can be registered. page 4-2 Omni-4000ST User’s Manual...
Page 77: Plu File Registration
Register the PLU data after selecting the PLU field listed on the screen. Returns to Registration Menu screen. Turns back the screen. Moves the cursor up and down. Turns over the screen. Displays PLU Data Registration screen. Deletes the selected data. Omni-4000ST User’s Manual page 4-3...
Page 78 Or, enter the desired PLU number (1 - 999999) using the numeric keys, and press the [PLU] stroke key. Press the [DETAIL] button on the screen. PLU Data Registration 1/3 screen is displayed. page 4-4 Omni-4000ST User’s Manual...
Page 79 Saves the PLU data and returns to the previous screen. Turns over the screen. Deletes the called PLU data. REGISTRATION METHOD The table below is the summarized registration examples. Select necessary items and make necessary registrations. Omni-4000ST User’s Manual page 4-5...
Page 80 Chapter 4 PROGRAMMING MODE page 4-6 Omni-4000ST User’s Manual...
Page 81 Chapter 4 PROGRAMMING MODE Omni-4000ST User’s Manual page 4-7...
Page 82 Chapter 4 PROGRAMMING MODE page 4-8 Omni-4000ST User’s Manual...
Page 83 4.2.2 PLU DATA REGISTRATION 2/ 3 SCREEN Saves the PLU data and returns to the previous screen. Turns over the screen. REGISTRATION METHOD The table below is the summarized registration examples. Select necessary items and make necessary registrations. Omni-4000ST User’s Manual page 4-9...
Page 84 Chapter 4 PROGRAMMING MODE page 4-10 Omni-4000ST User’s Manual...
Page 85 Chapter 4 PROGRAMMING MODE Omni-4000ST User’s Manual page 4-11...
Page 86 4.2.3 PLU DATA REGISTRATION 3/3 SCREEN Saves the PLU data and returns to the previous screen. Turns over the screen. REGISTRATION METHOD The table below is the summarized registration examples. Select necessary items and make necessary registrations. page 4-12 Omni-4000ST User’s Manual...
Page 87 Chapter 4 PROGRAMMING MODE Omni-4000ST User’s Manual page 4-13...
Page 88 Chapter 4 PROGRAMMING MODE page 4-14 Omni-4000ST User’s Manual...
Page 89: Plu Name Registration
A PLU name can be easily registered simply by pressing the [PLU NAME] button on the Registration Menu screen. Register the PLU name after calling the desired PLU. Press [PLU NAME] on the Registration Menu screen. Text edit screen is displayed. Specify the desired PLU. EXAMPLE PLU No. "1" Omni-4000ST User’s Manual page 4-15...
Page 90 “Text Editing”. 2046 Press the [FIX] button to confirm the text image. Press the [RETURN] button on the screen. D BEEF Save confirmation screen is displayed. Press the [EXECUTE] button to save the data. page 4-16 Omni-4000ST User’s Manual...
Page 91: Extra Message Registration
EXAMPLE Message No. "1" Press the [EDIT] button.. Text edit screen is displayed. Enter the desired text using the For character entry, keyboard on the screen. refer to section 4.12 “Text Editing”. 2046 Omni-4000ST User’s Manual page 4-17...
Page 92 Chapter 4 PROGRAMMING MODE Press the [FIX] button to confirm the text image. Press the [RETURN] button on the screen. Save confirmation screen is displayed. Press the [EXECUTE] button to save the data. page 4-18 Omni-4000ST User’s Manual...
Page 93: Pop Message Registration
(1 - 999) and press the [PLU] stroke key. EXAMPLE Message No. "1" Press the [EDIT] button. Text edit screen is displayed. Enter the desired text using the For character entry, keyboard on the screen. refer to section 4.12 “Text Editing”. Omni-4000ST User’s Manual page 4-19...
Page 94 Chapter 4 PROGRAMMING MODE Press the [FIX] button to confirm the text image. Press the [RETURN] button on the screen. Save confirmation screen is displayed. Press the [EXECUTE] button to save the data. page 4-20 Omni-4000ST User’s Manual...
Page 95: Coupon Message Registration
EXAMPLE Message No. "1" Press the [EDIT] button. Text edit screen is displayed. Enter the desired text using the For character entry, keyboard on the screen. refer to section 4.12 000001 “Text Editing”. 1022 Omni-4000ST User’s Manual page 4-21...
Page 96 Chapter 4 PROGRAMMING MODE Press the [FIX] button to confirm the text image. Press the [RETURN] button on the screen. Save confirmation screen is displayed. Press the [EXECUTE] button to save the data. page 4-22 Omni-4000ST User’s Manual...
Page 97: Store Name/Address Registration
When selecting a store number other than “9999”, press [ ] [ ] to find the desired number, or enter the store number (1 - 9999) and press the [PLU] stroke key. EXAMPLE Store No. "1" Omni-4000ST User’s Manual page 4-23...
Page 98 Save confirmation screen is displayed. Press the [EXECUTE] button to save the data. Press the [ADDRESS] field to make a selection, and press the 9999 [EDIT] button on the screen. NAME HYPER ISHIDA ADDRESS page 4-24 Omni-4000ST User’s Manual...
Page 99 Press the [RETURN] button on the screen. Save confirmation screen is displayed. Press the [EXECUTE] button to save the data. Registered name and address appear on the screen. 9999 NAME HYPER ISHIDA ADDRESS SHIGA Omni-4000ST User’s Manual page 4-25...
Page 100: Tray Message Registration
. Press the [TRAY MESSAGE] button on the Registration Menu screen. Tray Program 1/2 screen is displayed. Enter the desired tray number (1- 9999) using the numeric keys, and press the [PLU] stroke key. EXAMPLE Tray No. "4" page 4-26 Omni-4000ST User’s Manual...
Page 101 . Check the finished wrapping condition. The weighing area can be used as the scale Change the film tension and when [WEIGHT] is length if necessary. pressed. Press [WEIGHT] again to release this function after weighing. Omni-4000ST User’s Manual page 4-27...
Page 102 Enter the tray name using the For character entry, keyboard on the screen. refer to section 4.12 “Text Editing”. . Press the [RETURN] button on the screen. Save confirmation screen is displayed. Press the [EXECUTE] button to save the data. page 4-28 Omni-4000ST User’s Manual...
Page 103 Chapter 4 PROGRAMMING MODE 4.8.3 TRAY PROGRAM 2/2 SCREEN The machine can memorize the label pasting position for each tray either in horizontal or vertical direction. Press the [PAGE] button. Tray Program 2/2 (Label) screen is displayed. Omni-4000ST User’s Manual page 4-29...
Page 104 The angle can be set to 0°, 90° and - 90°. When the option printer is used, the angle can be changed in 15° increments. (3) Press [RETURN] to return to the Tray Program screen. page 4-30 Omni-4000ST User’s Manual...
Page 105 Chapter 4 PROGRAMMING MODE Enter a numeric value (5 – 8) and press [SET] in the Label Position (Vertical) field. Decide the labeling position in the same procedure. Finally, decide the standard labeling position. Omni-4000ST User’s Manual page 4-31...
Page 106: Department Name Registration
Or enter the desired department number (1 - 9999), and press the [PLU] stroke key. Example Department No. "2" Press the [EDIT] button on the screen when changing or creating the selected department name data. page 4-32 Omni-4000ST User’s Manual...
Page 107 Text edit screen is displayed. For character entry, refer to section 4.12 Enter the department name “Text Editing”. using the keyboard on the screen. Press the [RETURN] button on the screen. Press the [EXECUTE] button to save the data. Omni-4000ST User’s Manual page 4-33...
Page 108: Category Preset Registration
Displays the index title registration screen. Deletes all the data in the selected index number Press the [CATEGORY PRESET] button on the Registration Menu screen. Category Preset Registration screen is displayed. Select the index to register. page 4-34 Omni-4000ST User’s Manual...
Page 109 Select the PLU to allocate from the can also be performed list. by pressing the preset key after numeric entry. Specify the PLU to allocate with the cursor and press the allocation position key of the preset keyboard. Omni-4000ST User’s Manual page 4-35...
Page 110: Plu Preset Registration
Select the PLU to allocate from the can also be performed list. by pressing the preset key after numeric entry. Specify the PLU to allocate with the cursor and press the allocation position key of the preset keyboard. page 4-36 Omni-4000ST User’s Manual...
Page 111: Text Editing
Used to delete a character at the position where the cursor is positioned. Used to delete a character by moving the cursor back. Used to select the entered characters for editing the text. Also used to move the cursor left or right. Omni-4000ST User’s Manual page 4-37...
Page 112 Touching this key changes the key display in the following order. 4.12.2 SHIFT ON /OFF The [SHIFT ON] or [SHIFT OFF] button is used to select either lower-case or upper-case character. Shift OFF (Upper-case character) Shift ON (Lower-case character) page 4-38 Omni-4000ST User’s Manual...
Page 113 “Roast Fillet Steak” Edit the text as necessary. When the text editing is completed, touch [FIX] to confirm the edited text image on the text display field. Then, touch [RETURN] to finish the text editing. Omni-4000ST User’s Manual page 4-39...
Page 114 Chapter 4 PROGRAMMING MODE . The confirmation screen appears on the display for saving. Then, touch [EXECUTE] to save the text. page 4-40 Omni-4000ST User’s Manual...
Page 115 Example “Reverse” Touch [STYLE 1] repeatedly until [REVERSE] appears on the key display. . Enter the desired characters. Example “Roast Fillet Steak” Touch [FIX] to confirm the edited text image on the display. Omni-4000ST User’s Manual page 4-41...
Page 116 If not selected, touch [INSERT] to change the key display to [SELECT]. . Select [REVERSE] by touching [STYLE 1] repeatedly. Example “Reverse” . Use [←] and [→] keys to select the characters to be emphasized. page 4-42 Omni-4000ST User’s Manual...
Page 117 The following procedure is used to move the cursor back, and delete a character if any. . If you have misspelled, press [BACK SPACE] on the screen to delete the character that has been lastly entered. Example “Roast Fillet Steal” Omni-4000ST User’s Manual page 4-43...
Page 118 The following procedure is used to delete a character at the position where the cursor is placed. . The displayed text is misspelled. Example “Roast Fillet Steak” . Place the cursor at the character to be deleted. Then, touch [DELETE] on the screen to delete the character. page 4-44 Omni-4000ST User’s Manual...
Page 119 . Confirm that [INSERT] is selected on the screen. When not selected, touch [SELECT] to change the key display to [INSERT]. . Move the cursor to the position where the character to be inserted. Then, enter the character “L”. Omni-4000ST User’s Manual page 4-45...
Page 120 [COPY] on the screen. . The copy confirmation screen appears on the display. Then, touch [EXECUTE] to copy the original text to the text field of the designated file. page 4-46 Omni-4000ST User’s Manual...
Page 121 Chapter 4 PROGRAMMING MODE . The text “Roast Fillet Steak” of the PLU No.5 is copied to the text display field of the PLU No.25. Omni-4000ST User’s Manual page 4-47...
Page 122 Chapter 4 PROGRAMMING MODE page 4-48 Omni-4000ST User’s Manual...
Page 123 5.1 STARTING PROCEDURE..........5-2 5.2 SETUP MENU ............... 5-3 5.3 EXPIRY DATE SETTING..........5-4 5.4 PASSWORD SETTING ..........5-6 5.5 WORD-WRAP WIDTH SETTING ........5-7 5.6 REFERENCE DATA SETUP ......... 5-8 5.7 TOTAL ADD SETTING ..........5-11 Omni-4000ST User’s Manual page 5-1...
Page 124: Chapter 5 Setup Mode
Wait until the initial screen appears. Press the [MENU] button. Main Menu screen is displayed. Press the [SETUP] button. Set u p M e n u Sc re en ( 1/ 2) Setup Menu screen is displayed. page 5-2 Omni-4000ST User’s Manual...
Page 125: Setup Menu
• Set whether or not to add the data to totals. • Set a maximum of 20 target PLUs to be added to hourly totals. • Set the weight data type (fixed weight, actual weight) when a fixed price PLU is added to totals. Omni-4000ST User’s Manual page 5-3...
Page 126: Expiry Date Setting
Chapter 5 SETUP MODE 5.3 EXPIRY DATE SETTING Changes to the first screen of the Setup Menu. Expiry Date Setting Screen Text Edit Screen page 5-4 Omni-4000ST User’s Manual...
Page 127 Press the [EDIT] button to display the text edit screen. After Switch Select the “After Switch” field. Press the [EDIT] button to display the text edit screen. Pack Date Select the “Pack Date” field. Press the [EDIT] button to display the text edit screen. Omni-4000ST User’s Manual page 5-5...
Page 128: Password Setting
Set the password data by pressing this button after 6-gigit numeric entry. Enter “000000” and press this button to cancel the password. Mode Selection Buttons Press the desired button(s) to select the mode that requires password entry. page 5-6 Omni-4000ST User’s Manual...
Page 129: Word-Wrap Width Setting
Enter a numeric value (1-9999) and press the [SET] button to set the value (unit: 0.1mm) as a word-wrap width value. Extra Message Pitch Enter a numeric value (1-99) and press the [SET] button to set the value (unit: 0.1mm) as a gap between characters. Omni-4000ST User’s Manual page 5-7...
Page 130: Reference Data Setup
Chapter 5 SETUP MODE 5.6 REFERENCE DATA SETUP Determines the settings and returns to the first screen of the Setup Menu. Turns over the screen. Reference Data Setup 1/2 Screen Reference Data Setup 2/2 Screen page 5-8 Omni-4000ST User’s Manual...
Page 131 This setting is effective only when “REFFER" is specified by the Open Price setting in PLU registration. Standard Tare Set the standard tray weight. This setting is effective only when “REFFER" is specified by the Forced Tare setting in PLU registration. Omni-4000ST User’s Manual page 5-9...
Page 132 This setting is effective only when “REFFER" is specified by the Logo setting in PLU registration. Safe handling image Set the safe handling image number. number This setting is effective only when “REFFER" is specified by the Safe Handling Image setting in PLU registration. page 5-10 Omni-4000ST User’s Manual...
Page 133: Total Add Setting
PLU or entering the PLU number. Time Zone Set for Individual PLU Screen Delete a commodity from target commodities by pressing this button after selecting the PLU to be deleted. Omni-4000ST User’s Manual page 5-11...
Page 134 Select whether or not to clear Daily Total when turning off the machine. This is not displayed at a slave machine in master/slave specification. Fixed Price PLU Weight Select to add either “Fixed Weight” or “Real Weight” to the fixed price Addition Mode total. page 5-12 Omni-4000ST User’s Manual...
Page 135 Design and specifications are subject to change without notice. 44 SANNO-CHO, SHOGOIN, SAKYO-KU KYOTO, 606-8392 JAPAN PHONE: 81-75-771-4141 FACSIMILE: 81-75-751-1634 URL: http://www.ishidajapan.com...

ISHIDA Omni-4000ST User Manual

Chapter 1 Before Using this Machine

Chapter 2 Normal Mode

Chapter 3 Total Mode

Chapter 4 Programming Mode

Chapter 5 Setup Mode

Quick Links

Need help?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for ISHIDA Omni-4000ST

Summary of Contents for ISHIDA Omni-4000ST

Table of Contents