Titan Tool Speeflo PowrLiner 6950 Owner's Manual
  1. Manuals
  2. Brands
  3. Titan Tool Manuals
  4. Lawn and Garden Equipment
  5. Speeflo PowrLiner 6950
  6. Owner's manual

Titan Tool Speeflo PowrLiner 6950 Owner's Manual

Titan tool airless sprayer owner's manual
Hide thumbs
Table of Contents

Advertisement

Quick Links

PowrLiner 6950
Model Number
2 Gun
Printed in the U.S.A.
SPEEFLO
0290010
Owner's Manual
For professional use only
Do not use this equipment
before reading this manual!
NOTE: This manual contains important
warnings and instructions. Please
read and retain for reference.
© Titan Tool Inc. All Rights Reserved. Form No. 0290915B
•
0611

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Speeflo PowrLiner 6950 and is the answer not in the manual?

Questions and answers

Summary of Contents for Titan Tool Speeflo PowrLiner 6950

  • Page 1 SPEEFLO PowrLiner 6950 Model Number NOTE: This manual contains important 2 Gun 0290010 warnings and instructions. Please read and retain for reference. © Titan Tool Inc. All Rights Reserved. Form No. 0290915B • 0611 Printed in the U.S.A.

  • Page 2: Safety Precautions

    (add more hose if necessary). Flammable vapors are often heavier than air. Floor area must be extremely well ventilated. The pump contains arcing parts that emit sparks and can ignite vapors. © Titan Tool Inc. All rights reserved.

  • Page 3: Grounding Instructions

    DO NOT use this equipment to spray water or acid. proper outlet installed by a qualified electrician. Grounded Outlet IMPORTaNT: Do not lift by cart handle when loading or unloading. Grounding Pin Cover for grounded outlet box © Titan Tool Inc. All rights reserved.

  • Page 4: Table Of Contents

    SAE O-Ring Fitting Installation .......... 31 Accessories and Service Kits ..........31 Second Gun Assembly ............32 SC-6 Striping Tip Chart ............. 34 Electrical Schematic............... 33 Spray Gun Positions .............. 35 Warranty .................. 36 © Titan Tool Inc. All rights reserved.

  • Page 5: Introduction

    If you notice any undesirable operating characteristics while using a gasoline that contains alcohol, or one that you think contains alcohol, switch to a gasoline that you know does not contain alcohol. © Titan Tool Inc. All rights reserved.

  • Page 6: Setup

    The gun lever on the right handlebar triggers the gun or guns. The selector on the trigger must be set for the first gun, both guns, or the second gun . © Titan Tool Inc. All rights reserved.

  • Page 7: Preparing To Paint

    12. Turn the pressure control knob clockwise approximately control knob fully counterclockwise, 1/3 of the way down to increase pressure. • move the throttle lever to the slow position, and © Titan Tool Inc. All rights reserved.

  • Page 8: Painting

    To start the electric motor, move the ON/OFF switch to the ON position. 7. Turn the pressure control knob clockwise approximately 1/3 of the way down to increase pressure until the sprayer cycles evenly and paint flows freely from the bleed hose. © Titan Tool Inc. All rights reserved.

  • Page 9: Pressure Relief Procedure

    IMPORTaNT: use only compatible solvents when cleaning out oil based enamels, lacquers, coal tar, and epoxies. check with the fluid manufacturer for the recommended solvent. 4. Place the bleed hose into a metal waste container. © Titan Tool Inc. All rights reserved.

  • Page 10: Maintenance

    5. Place the thin Teflon gasket onto the step at the top of the filter body. 6. Place the thick Teflon gasket onto the top of the thin gasket. 7. Tighten the filter cap assembly onto the filter body. © Titan Tool Inc. All rights reserved.

  • Page 11: Maintaining The Hydraulic System

    (see the by a pulley combination designed to produce full paint Troubleshooting section). delivery at maximum RPM. 3. The warranty on gasoline engines or electric motors is limited to the original manufacturer. © Titan Tool Inc. All rights reserved.

  • Page 12: Replacing The Motor Brushes (Electric Motor)

    Brush Holder Spring Spring Clip 6. Place the spring on the brush as shown above. Push in and hook the spring clip. Repeat this procedure for the other side. 7. Reinstall both inspection covers. © Titan Tool Inc. All rights reserved.

  • Page 13: Troubleshooting

    Hose size or length is too small or too long Increase hose size to minimize pressure drop through hose and/or reduce hose length. Solvent has caused upper packing to swell Pump chatters on up or down Replace packing. stroke © Titan Tool Inc. All rights reserved.

  • Page 14: Hydraulic Motor

    This will help determine NOTE: Engine labors at stall on if center o-ring is blown on spool valve. If hot, remove both strokes. and replace o-ring. Bad hydraulic pump Replace hydraulic pump. © Titan Tool Inc. All rights reserved.

  • Page 15: Spray Patterns

    Remove restrictions in system; clean tip screen if filter is used. Round pattern Worn tip Replace tip. Fluid too heavy for tip Increase pressure. Thin material. Change nozzle tip. © Titan Tool Inc. All rights reserved.

  • Page 16: Français

    3300 PSI. Ceci est valable de chiffons et autres matières inflammables. Français © Titan Tool Inc. Tous droits réservés.
  • Page 17 13. Ne pulvérisez pas à l’extérieur par temps venteux. 14. Débranchez toujours le cordon électrique de la prise avant de travailler sur l’équipement. IMPORTaNT: Ne pas soulever par la poignée du chariot lors du chargement ou du déchargement. © Titan Tool Inc. Tous droits réservés. Français...

  • Page 18: Español

    11. Antes de utilizar el aparato, verifique que todas las que pulverice. Lea las hojas de datos sobre seguridad conexiones son seguras. de los materiales (MSDS) y las etiquetas en los botes de Español © Titan Tool Inc. Todos los derechos reservados.
  • Page 19 13. No pulverice al aire libre si hace viento. 14. Desenchufe siempre el cable antes de trabajar en el equipo. IMPORTaNTE: No cargue el equipo por el asa del carrito durante la carga y descarga. © Titan Tool Inc. Todos los derechos reservados. Español...

  • Page 20: Parts Lists And Service Instructions

    12 gallon hopper 840-218 Bleed hose assembly w/valve 103-842 Siphon hose assembly 506-146 Convertokit, 4.8 HP, Gasoline 779-564 Cart assembly 665-xxxx SC-6 striping tips (optional, see tip chart near the end of this section) © Titan Tool Inc. All rights reserved.

  • Page 21: Hydraulic System Assembly

    Use blue Loctite on threads, Torque to 8 FT/LBS (11 N/m) 449-135 Spacer 451-121 Elbow (not shown) Torque to 8 FT/LBS (11 N/m) 941-555 Ball valve (not shown) Torque to 15 FT/LBS (20,5 N/m) 27, 32-33 © Titan Tool Inc. All rights reserved.

  • Page 22: Gas Convertokit

    Screw 449-144 Bracket 980-307 449-165 Vibration pad 449-170 Mounting Plate 449-219 Mounting plate 424-255 Spring 431-181 Belt, “V” (not shown, not part of assembly) 431-181 Belt, “V” (not shown, not part of assembly) © Titan Tool Inc. All rights reserved.

  • Page 23: Siphon Hose Assembly

    Description Qty. 944-030 Bleed valve assembly 500-516 Hose assembly 103-300 Bleed tube (includes item 4) Item Part No. Description Qty. 779-018 Axle 103-118 Diffuser 779-011 Frame 779-017 Spacer 779-016 Wheel 779-019 Lock nut © Titan Tool Inc. All rights reserved.

  • Page 24: Cart Assembly

    Rear wheel 757-014 Gun support bar 761-178 Hex screw 176-919 Washer 862-002 Lock washer 779-118 Guide block 756-080 Spring washer 862-436 Screw 730-148 Socket screw 756-078 Castle nut 703-079 Screw 756-087 Lock spring © Titan Tool Inc. All rights reserved.
  • Page 25 Handle assembly Handle bar, left 0528245 424-247 Cable clip 779-090 Kill switch 862-468 Screw 700-139 Screw 862-410 Lock nut, 3/8” 779-193 Screw 856-744 Screw 779-057 Control plate 759-033 Clamp knob 770-712 Carriage screw © Titan Tool Inc. All rights reserved.

  • Page 26: Hydraulic Motor

    Rod seal critical parts and affect its service life and 236-829 Motor/pump block warranty. all parts should be inspected for 235-029 Motor tube absolute cleanliness. 235-125 © Titan Tool Inc. All rights reserved.
  • Page 27 Install the spool through the top of the cylinder head, down into the sleeve. IMPORTaNT: Do not use Piston Lube pump packing lubricant. It is a solvent and will severely damage seals and O-Rings of the hydraulic motor. © Titan Tool Inc. All rights reserved.

  • Page 28: Fluid Section

    Fluid section service kit, minor (includes items 1, 3, 4, 10, 12, 15, 18, 20, and Loctite P/N 426-051) 236-010 Foot valve assembly (includes items 17–21) 236-050 Outlet valve assembly (includes items 9–13) © Titan Tool Inc. All rights reserved.
  • Page 29 (12) into the displacement rod (6). 8. Clean the threads on the outlet valve housing (13) and coat the threads with blue Loctite #242. Make sure the Loctite is only on the threads. © Titan Tool Inc. All rights reserved.

  • Page 30: Filter Assembly

    (1) 3/8” NPT(F) plugged for additional gun hookup. 759-015 Clevis pin Wetted Parts ........Carbon steel with electroless 424-217 Lever plate nickel and cadmium plating, 759-033 Knob stainless steel, tungsten carbide, Teflon 424-227 Spool © Titan Tool Inc. All rights reserved.

  • Page 31: Sae O-Ring Fitting Installation

    424-841 Bead Dispenser, 2nd Gun Kit w/Hopper, 12” ine indicator.) width Bent washer allows for o-ring extrusion Avoid leaving fitting too far out. O-ring cut on thread © Titan Tool Inc. All rights reserved.

  • Page 32: Second Gun Assembly

    Refer to the “Spray Gun Positions” illustration 858-636 Screw, hex head near the back of this manual. 550-290 Airless gun, S-3 661-517 Reversible tip, SC6 665-1908 Striping tip, SC6 © Titan Tool Inc. All rights reserved.

  • Page 33: Electrical Schematic

    Connect both cables to the blocks. Electrical Schematic Engine Stop Switch Wire Assembly 779-147 Wire Assembly 779-148 YELLOW BLACK Engine Wire Assembly YELLOW 779-242 Ground GREEN PINK Wire Assembly 779-149 12V Adapter © Titan Tool Inc. All rights reserved.

  • Page 34: Striping Tip Chart

    All traffic paints — High speed, heavy film 665-4308 4”-6” (102-152 mm) .043” (1.09 mm) All traffic paints — High speed, heavy film 665-4312 6”-8” (152-203 mm) .043” (1.09 mm) All traffic paints — High speed, heavy film © Titan Tool Inc. All rights reserved.

  • Page 35: Spray Gun Positions

    Spray Gun Positions Single Line One Gun Curb Two Lines Two Gun Curb Spraying Around Obstacles Two Lines or One Wide Line © Titan Tool Inc. All rights reserved.

  • Page 36: Warranty

    Warranty Titan Tool, Inc., (“Titan”) warrants that at the time of delivery to the original purchaser for use (“End User”), the equipment covered by this warranty is free from defects in material and workmanship. With the exception of any special, limited, or extended warranty published by Titan, Titan’s obligation under this warranty is limited to replacing or repairing without charge those parts which, to Titan’s...

Table of Contents