WARNING LABELS THERE IS A RISK ASSUMED BY INDIVIDUALS WHO USE THIS TYPE OF EQUIPMENT. TO MINIMIZE RISK, YOU MUST FOLLOW THESE RULES: >(9505.! WARNING! MAINTENANCE SCHEDULE :HML[` HUK 4HPU[LUHUJL VM *HISLZ IMPORTANT: Cable inspection should be performed daily. Replace and damaged or worn cable immediately.
IMPORTANT SAFETY INSTRUCTIONS Unpacking the Equipment When using exercise equipment, you should always take basic precautions, including the following: Obtaining Service Personal Safety During Assembly Retain this Owner’s Manual for future reference. Part numbers are required when ordering parts.
HARDWARE ILLUSTRATION PART 18 - M12X175mm Hex Head Bolt, 2 PCS. PART 19 - M10X42mm Hex Head Bolt, 21 PCS. PART 20 - M10X62mm Hex Head Bolt, 16 PCS. PART 21 - M10X72mm Hex Head Bolt, 4 PCS. PART 22 - M10X102mm Hex Head Bolt, 4 PCS. PART 23 - M6X8mm Screw, 3 PCS - Reserve for future usage.
Page 9
HARDWARE ILLUSTRATION PART 27 - M10 Washer, 90 PCS. PART 28 - M12 Nylon Lock Nut, 2 PCS. PART 29 - M10 Nylon Lock Nut, 45 PCS. PART 33 - Push Nut, 1 PCS. PART 34 - Pivot Axle, 1 PCS. PART 35 - M12 Nut, 1 PCS.
PART LIST PART A - LEFT LOWER BEAM, 1 PCS. PART B - RIGHT LOWER BEAM, 1 PCS. PART C - BASE FRAME, 1 PCS. PART D - SELECTING UPRIGHT, 2 PCS. PART E - LEFT UPRIGHT, 1 PCS. PART F - RIGHT UPRIGHT, 1 PCS.
Page 11
PART LIST PART H - LAT BAR, 1 PCS. PART I - GUIDE ROD, 2 PCS. PART J - HANDLE ASSEMBLY, 2 PCS. PART K - DOUBLE PULLEY, 2 PCS. PART L - PULLEY HOLDER, 2 PCS. PART M - SINGLE PULLEY, 1 PCS.
S T E P Be careful to assemble all components in the sequence they are presented. NOTE: Finger tighten all hardware first in this step. Wrench tighten bolts at the end of this step, some components may be pre-assembled. Nylon lock nuts will not fully screw onto bolts, must wrench tighten.
Page 14
S T E P Be careful to assemble all components in the sequence they are presented. NOTE: Finger tighten all hardware in this step. DO NOT wrench tighten until the end of Step 4, some components may be pre-assembled. Nylon lock nuts will not fully screw onto bolts, must wrench tighten.
Page 16
S T E P Be careful to assemble all components in the sequence they are presented. NOTE: Finger tighten all hardware in this step. DO NOT wrench tighten until the end of Step 4, some components may be pre-assembled. Nylon lock nuts will not fully screw onto bolts, must wrench tighten.
Page 18
S T E P Be careful to assemble all components in the sequence they are presented. NOTE: Finger tighten all hardware first. Wrench tighten all bolts at the end of this step, some components may be pre-assembled. Nylon lock nuts will not fully screw onto bolts, must wrench tighten.
Page 20
S T E P Be careful to assemble all components in the sequence they are presented. NOTE: Finger tighten all hardware first. DO NOT wrench tighten until the end of step 8, some components may be pre-assembled. Nylon lock nuts will not fully screw onto bolts, must wrench tighten.
Page 22
S T E P Be careful to assemble all components in the sequence they are presented. NOTE: Finger tighten all hardware first. DO NOT wrench tighten until the end of step 8, some components may be pre-assembled. Nylon lock nuts will not fully screw onto bolts, must wrench tighten.
Page 24
S T E P Be careful to assemble all components in the sequence they are presented. NOTE: Finger tighten all hardware first. DO NOT wrench tighten all pulleys until the end of step 8, some components may be pre-assembled. Nylon lock nuts will not fully screw onto bolts, must wrench tighten.
Page 26
S T E P Be careful to assemble all components in the sequence they are presented. NOTE: Finger tighten all hardware first. Wrench tighten all pulleys at the end of this step, some components may be pre-assembled. Nylon lock nuts will not fully screw onto bolts, must wrench tighten. allen key screw strip the plastic coating off the cable before your tighten it down.