1. Manuals
  2. Brands
  3. 909 Manuals
  4. Sander
  5. TBD15009
  6. Instruction manual

909 TBD15009 Instruction Manual

1/2 hp benchtop belt/disc sander
Hide thumbs
Table of Contents

Advertisement

Quick Links

INSTRUCTION MANUAL
TBD15009
1/ 2 HP
BENCH TOP
BELT/ DISC SA NDER

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the TBD15009 and is the answer not in the manual?

Questions and answers

Related Manuals for 909 TBD15009

Summary of Contents for 909 TBD15009

  • Page 1 INSTRUCTION MANUAL TBD15009 1/ 2 HP BENCH TOP BELT/ DISC SA NDER...

  • Page 2: Table Of Contents

    CONTENTS Introduction Warranty Power Tools Description of symbols For full details please visit us at www.909.com Specifications General safety rules Additional safety rules for belt & disc sanders Unpacking Accessories Know your product Getting to know your belt and disc sander...

  • Page 3: Description Of Symbols

    Manual before using your new 909 Power Tool. Take special care to heed the Cautions and Warnings. Conforms to relevant standards Your 909 power tool has many features that will make for electromagnetic compatibility. your job faster and easier. Safety, performance, and...

  • Page 4: General Safety Rules

    General safety rules 3) Personal safety a) Stay alert, watch what you are doing and use WARNING. Read all safety warnings and all instructions. common sense when operating a power tool. Do not Failure to follow the warnings and instructions may result in use a power tool while you are tired or under the electric shock, fire and/or serious injury.

  • Page 5: Additional Safety Rules For Belt & Disc Sanders

    4) Power tool use and care i) Children should be supervised to ensure that they do not play with the appliance. a) Do not force the power tool. Use the correct power tool for your application. 5) Service The correct power tool will do the job better and safer at the rate for which it was a) Have your power tool serviced by a qualified repair designed.

  • Page 6: Unpacking

    • Bolt the sander to its work surface. • Never use another person as a substitute for a table extension, or as additional support for a workpiece that • Never stand on the tool. Serious injury could occur if the is longer or wider than the basic sander table, or to help tool tips.

  • Page 7: Accessories

    Accessories The Belt & Disc sander is supplied with the following parts: 1. Work table 2. Table support 3. Mitre gauge 4. Sanding disc 5. Disc guard 6. Work support 7. Table lock knob and washer 8. Washers (6.5 x 17.8 x 1.6) x2 9.

  • Page 8: Know Your Product

    Know your product 1. On/off switch 2. Base 3. Mounting holes (x2) 4. Work table 5. Mitre gauge 6. Disc guard 7. Sanding disc 8. Sanding plate 9. Work support 10. Work support hex screw 11. Sanding belt 12. Belt bed 13.

  • Page 9: Getting To Know Your Belt And Disc Sander

    4. Place belt and disc Sander on workbench aligning holes Getting to know your belt and disc sander drilled in workbench. WARNING: To avoid injury from accidental start, turn switch 5. Insert two M8 screws and tighten hex nuts. ’OFF’ and remove plug from power source outlet before Installing sanding disc and guard making any adjustments.

  • Page 10: Installing Table Assembly

    Installing table assembly Auxiliary mounting for vertical sanding 1. Position table support against 1. Remove work support (9) lock table (4) and align the holes. and bolt (10), and remove work support. 2. Position the table support in the corresponding holes on the 2.

  • Page 11: Removing The Belt

    To remove the belt Turning on and off 1. Connect the plug to the power supply 2. To turn on press the green ‘ON’ button. 3. To switch off, press the red ‘OFF’ button. 1. Use a screwdriver (not included) to undo the dust cover screws on both sides of the belt carriage.

  • Page 12: Positioning Belt Bed

    Positioning belt bed End sanding on the sanding belt The belt bed locking hex screw 1. It is more convenient to sand locks the belt bed (12) in a the ends of long workpieces vertical or horizontal position. with the sanding belt in a vertical position.

  • Page 13: Sanding Small End Surfaces On The Sanding Disc

    Sanding small end surfaces Maintenance on the sanding disc Note: Always wear eye protection when cleaning the tool. 1. Use of the mitre gauge WARNING: Always ensure that the sander is switched off is recommended for this and unplugged from the power supply before carrying out operation.

Table of Contents