Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Alert 550R LCD
Summary of Contents for Alert 550R LCD
- Page 2 As with any product that performs automatic functions, there are certain safety precautions that Automatic Re-Arm J. DISARMING WITHOUT A TRANSMITTER . .................. 8 you must practice and be aware of. Overrides the Alarm without Password Pin Code . Keep the transmitter out of children’s reach. Overrides the Alarm With Password Pin Code . Do not leave anyone in the vehicle while running on remote control. K. VALET MODE ........................... 8 . Alert servicing personnel that the vehicle can be started automatically. Enter Valet Mode 4. Do not start the vehicle by remote while it’s in an enclosed area or garage. Exit Valet Mode 5. Always apply the parking brake and lock the vehicle as you exit the vehicle. Remote Valet Mode L. CAR LOCATOR .......................... 9 6. The vehicle windows must be rolled up. M. PANIC FUNCTION ........................9 7. Should the unit malfunction, disconnect the fuse until the problem is corrected.
-
Page 3: Table Of Contents
6. Set Up Fixed Count Down (Parking) Timer 7. Out of Range Indication B. 2-WAY LCD REMOTE CONTROL TRANSCEIVER OPERATION ONLY: D. TIMER SETTING ........................ Transceiver Button System Function Remark . Timer Setting. System’s Status Check Press within seconds . Alert Alarm Timer Setting F – F – . Count Down Timer Setting F – (·) Monitor Indoor Temperature Press within seconds 4. Time Set-up for Daily Timer Start ✱ Daily Timer Start Press within seconds F –... - Page 4 C. LED INDICATORS armed. The vehicle doors will lock upon System Arm Door Ajar arming when interfaced with the security Status system. Disarmed Slow flash Armed Clear The Flashing Icon: Press the F Flash PAssive Starter Disabled button times within seconds will clear the Fast flash Passive arming flashing icon on the LCD screen transceiver. On (solid) Valet mode AJAr WArNINg: If the siren sounds chirps, then you have left a door, trunk, or hood D. CHIRP INDICATORS E. PARKING LIGHT lid ajar. Chirp Function Parking Light Function H.
- Page 5 tem is now disarmed. The vehicle doors will unlock and dome light will turn on for 0 seconds Exit Valet mode: upon disarming when interfaced with the security system. . Return to normal operation, turn ignition ‘ on’ . System disarm pAThWAY ILLUmINATION This feature turns the parking light “ ON” for 0 . Push and hold valet switch for seconds, The LED will turn off indicating the system is exiting seconds upon a unlock signal and for 0 seconds upon the lock signal. the valet mode. TWO STEp dOOr UNLOCk: This feature will independently unlock the drives rEmOTE VALET: (System in Disarm or Valet mode) door only when disarming the security system. Pushing the button on the Press and release button on the transmitter three times within seconds to enter / exit valet transmitter a second time within seconds will unlock the entire vehicle. mode. A parking flash to confirm enters valet mode and two parking lights flashing to confirm exit AUTOmATIC rE-Arm (See Feature “I - 2” Programming): If this feature valet mode. is selected, the security system will automatically re-arm itself 60 seconds after disarming with L.
-
Page 6: Remote Start Operation
N. SYSTEM’S STATUS CHECK S. CHANNEL 4 TIMER CONTROL OUTPUT Press the transmitter (4) and the (4) buttons at the same time to ac- (For two-way transceiver operation only) tive Channel 4 function. Channel 4 is user-programmable timer output. You When you want to check the system’s present status through the LCD may program the built-in timer to send a ground signal for any time interval screen, Press the transceiver F button twice, within seconds press (C) button. It responds with one melody sound, the LCD screen should between second and minutes. For instance, this timer output may be used to turn on the headlight, power window or sunroof. (Factory defaults be illuminated. setting at momentary output.) O. DRIVER PAGING (For two-way transceiver operation only) T. CHANNEL 5 TIMER CONTROL OUTPUT It is useful the event that someone wants to page the driver of the parked Press the transmitter (5) and (5) buttons at the same time to active... -
Page 7: Engine Start Memorizing For The Vehicle With Standard
5. Once the engine is running, after couple seconds the parking light will turn on again The system senses the neutral transmission gear position automatically and there is no prior set- up required. The system in the standard transmission vehicle operates as following process when 6. and climate controls will activate and adjust the vehicles interior temperature to your you exit the vehicle to sense and memorize the neutral transmission gear position. If the vehicles 7. preset setting. (While the vehicle is running, the “ ” icon and the “ minutes” digit on the are of automatic transmission gear, this process is omitted. LCD screen will flash and it will indicate count down timer based on the 5, 0, 0 or 0 minute . While engine is running by ignition key, pull up the hand brake and place the transmission run time set up by your installation center.) gear in the neutral position. 8. The vehicle will run for 5 to 0 minute cycle and automatically shut down. (When the unit ✱ . Before turning off the engine, press the button twice on the transmitter. shuts off the count down timer will turn off and the transmitter will play a melody.) -- The LED indicator will flash times to confirm enter. Activate remote Start Engine running . Pull off the “ Ignition Key” from the key cylinder. -- Engine continues running until the pre-programmed time elapsed or shutdown input is received.-- 4. Exit from the vehicle and Close all doors. -- The engine still continues running and it is normal operating process.-- 5. Within minute from the time of step , press the button on the transmitter to lock the Note: The Remote Start Unit will not start the vehicle if any one of the following conditions exists:... -
Page 8: Temporary Stop Feature
. Press the brake pedal. ImpOrTANT: Timer Start should be used only in open areas, Never start and run the vehicle in on enclosed space as a garage or carport. Note: If the brake pedal is pressed before the key is in the ON position, the engine will shut down. 3 hours timer start with Temperature-control OFF: This feature is design for an extreme cold D. TEMPORARY STOP FEATURE: climate usage. The system will auto start the vehicle every hours, to prevent engine freezing and This feature allows the vehicle to remain running after the key has been removed from the hard to start. ignition. This feature is useful for occasions when you wish to exit and lock the vehicle for short A MAXIMUM OF SIX CYCLES CAN OCCUR. periods of time, but would like to leave the motor running and the climate control on. ✱ 3 hours timer start with Temperature-control: If you programmed the temperature ON to . Before turning off the engine, press the button twice on the transmitter and the LED operate. The system can be programmed to automatically start the vehicle engine whenever the indicator will flash times to confirm enter. temperature inside the vehicle reaches or drops below the preprogrammed temperature level. . Turn the ignition key to OFF position. (The engine will stay running.) The system will monitor the air temperature every hour and will only start the engine during . The engine will run until the pre-programmed time elapsed or shutdown input is received. extreme cold temperatures. There is three-temperature level to choose form. -
Page 9: Temperature Check
. Make sure the remote start system is not operating the engine. . The hood is opened. . Turn the ignition on. The LED and parking light will flash (4) times. The horn chirps (4) times. . The brake pedal is pressed. . The hand brake is released (for Standard Transmission Gear Vehicle) ✱ . Press the button twice to remote start the vehicle. As soon as the vehicle is running and 4. Engine is over-revved. {“Tachometer checking type” only} the parking light have turned on or flashing. 5. The pre-programmed run time (5 /0 / 0 / 0 minutes) has elapsed. ✱ . Immediately depress the button then press and hold the button for seconds. The ✱ 6. Press button twice on the remote transmitter under remote start mode . parking light will flash (4) times. The siren or horn chirps (4) times. The vehicle is no longer 7. Move the optional remote start enable toggle switch to OFF position. (If installed) programmed to start automatically. 8. The vehicle refused to start running after {} unsuccessful attempts. G. TEMPERATURE CHECK You can monitor through the LCD screen, the present indoor temperature of the passenger J. DISABLING THE REMOTE START SYSTEM: (If installed) compartment before cooling or heating your vehicle. This feature allows your system’s remote start unit to be temporarily disabled to prevent the vehicle from being remote started accidentally. This feature is useful if the vehicle is being serviced Press the transceiver F button first, within seconds press the (·) button; the in-door... -
Page 10: Battery Replacement
/-hour. Activate Channel 3 Activate Channel 4 Note: Press the button (Trunk Release). two times when the Activate Channel 5 Activate Channel 6 battery compartment is Time monitor Alert Alarm empty, then insert the new You have set morning call alarm battery. Count down (parking) Timer Vibration mode Reminder when time is up for Remote Control vibrates when the parking system is triggered B. THE REMOTE LCD ICONS WITH FUNCTION... - Page 11 1. Screen Lamp ON: Press and hold the F button one second, with one melody sound and the . If user is out of range, it has five short “ beep” sounds and the icon will disappear on the LCD screen lamp will turns on for 5 seconds LCD screen. 2. Clear the Flash Icon and melody Sound: Press the F button times within seconds will D. TIMER SETTING: clear the flash icon and melody sound on the LCD screen transceiver Transceiver Button Description Press Transceiver Button 3. Stop The Trigger melody Sound: While triggering the alarm the LCD screen will alert user Press & Hold the F Timer Setting (Hour) through melody sound and flashing trigger icon, press any button on the LCD remote transmit- ✱ for – and for + button for seconds ter to stop melody sound only. *Flashes digit for adjusting Press the F button once Time setting (Minute) ✱...
- Page 12 “ Minutes” digit until AM 0:0 6. Press the F button once again then icon flashes for alert alarm “ ON / OFF” setting 5. Press the F button for seconds with one-melody sound to confirm exit the timer 7. Press the button to start the count down timer, and the “ ON” icon will show on the program mode. LCD screen. 2. Alert Alarm Timer Setting: Example to PM 6:30 ✱ 8. Press the button to stop the count down timer, and the “ OFF” icon will show on the . Press & hold the SET button for seconds, with two-melody sound and the “ Hours” digit LCD screen. flashes for adjusting. 9. Press the F button for seconds with one-melody sound to confirm exit the timer . Press the F button twice, the LCD screen will shows % icon and “...
Need help?
Do you have a question about the 550R LCD and is the answer not in the manual?
Questions and answers
replacement alarm keyfob alert 550r lcd