Advertisement

StarBoard FX-E90W
User's Guide
Read this User's Guide and carefully retain it for future reference.
Before using this product, carefully read and fully understand the safety instructions. Store
this User's Guide nearby for ease of reference.
FXEW-ML110901

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the StarBoard FX-E90W and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Hitachi Solutions StarBoard FX-E90W

  • Page 1 StarBoard FX-E90W User’s Guide Read this User's Guide and carefully retain it for future reference. Before using this product, carefully read and fully understand the safety instructions. Store this User's Guide nearby for ease of reference. FXEW-ML110901...
  • Page 2 StarBoard FX-E90W Notices Reproduction or reprinting, without permission, of this User's Guide or any part thereof is prohibited. The contents of this User's Guide are subject to change without prior notice. Every effort has been made to ensure that this User's Guide is complete and correct. However, should any questionable points, mistakes, etc., come to your attention, please inform the vendor.
  • Page 3: Product Assurance Provisions

    StarBoard FX-E90W Product Assurance Provisions This product is limited to use in the country where the user bought this product. For warranty details, refer to "3. Appendix 3.7 Product Warranty Policy" at the end of this User's Guide. This first edition of the User's Guide (FXEW-ML110901) is for the following products:...
  • Page 4 StarBoard FX-E90W Introduction Thank you very much for purchasing Hitachi solutions’ StarBoard FX-E90W (henceforth referred to as "StarBoard"). This User's Guide has been created for people who already have a working knowledge of personal computers (henceforth referred to as "PC").
  • Page 5 StarBoard FX-E90W Safe Handling Safe Handling Markings and Symbols Various markings and symbols are used in this User's Guide and on this product, to ensure the safe and correct use of this product and to prevent personal injury and property damage. These symbols and their meanings are as explained below.
  • Page 6 StarBoard FX-E90W Safe Handling Safe Precautions Required Precautions (1) Precautions Regarding Operation WARNINGS Do not make modifications. Do not make any adjustments, repairs, or modifications not given in this User's Guide as doing so may lead to personal injury or damage to the product.
  • Page 7 StarBoard FX-E90W Safe Handling (2) Dealing with Trouble CAUTIONS What to do in case of emission of smoke, strange odor, or strange noise If an abnormal condition such as emission of smoke, strange odor, or strange noise happens to occur for some reason, immediately disconnect the product's USB cable from the PC.
  • Page 8 StarBoard FX-E90W Safe Handling NOTICE Disconnect the USB cable during extended periods of non-use. For safety reasons, disconnect the USB cable if the product is not going to be used for an extended period of time. Failure to comply may result in malfunction.
  • Page 9 StarBoard FX-E90W Safe Handling (5) Precautions Regarding Setup Environment WARNINGS Wall mounting work should be performed by a construction specialist. Improper work m ay result in death or personal injury due to the product falling during operation. Always use the specified mounting unit Improper assembly may cause the product to fall over.
  • Page 10 StarBoard FX-E90W Safe Handling NOTICE Do not use this product in locations subject to high temperature or high humidity. This product's usage environment conditions: Temperature: 5°C – 35°C Humidity: 20%RH – 80%RH (no condensation) Do not set up in locations subject to vibration and/or shock of impact.
  • Page 11 StarBoard FX-E90W Safe Handling Careful thought was given to the cautions on this device and in this User's Guide. However, unanticipated circumstances might occur. When operating this product, users themselves must exercise caution as well as follow instructions. WARNINGS Warnings Contents Page(s) Install this product on a vertical and flat surface.
  • Page 12 StarBoard FX-E90W Safe Handling NOTICE Notice Contents Page(s) - Do not set it up near equipment that might generate electromagnetic waves or radio frequencies, such as radio transmitters, televisions, copying machines or air conditioners. P.1-6 - Avoid locations that are dusty, that are subject to extremely high or low temperatures or humidity, or that are exposed to direct sunlight.
  • Page 13: Table Of Contents

    REPARATIONS 1.1.1 Product Outline ....................1-1 1.1.2 Features ....................... 1-1 ......................1-2 1.2 P ARTS HECK 1.2.1 StarBoard ......................1-2 1.2.2 Electronic Pen (option)..................1-3 ..................... 1-4 1.3 R OLE OF 1.3.1 StarBoard ......................1-4 1.3.2 Function Area....................... 1-5 1.3.3 Electronic Pen (option)..................1-6 ....................
  • Page 14: Introduction

    User’s Guide, it means “electronic pen.” - You can write directly onto the PC screen After installing the provided StarBoard Software onto a PC, you can use your finger or the pen to write characters or images directly onto the PC screen. The input characters or drawn images are imported as digital data in real time into the PC, where they can be saved or printed.
  • Page 15: Parts Check

    Introduction 1.2 Parts Check After unpacking, make sure that all the following parts are present. 1.2.1 StarBoard [1] Parts Name StarBoard Wall-mounting bracket Brush Stylus pen StarBoard Software DVD-ROM StarBoard Software Startup Guide StarBoard FX-E90W Startup guide Warranty Sheet English...
  • Page 16: Electronic Pen (Option)

    StarBoard FX-E90W Introduction 1.2.2 Electronic Pen (option) [1] Parts Name Electronic pen AAA alkaline battery Spare pen tip English...
  • Page 17: Role Of Each Part

    Lit green: Normal within this area. Flashing orange: Recognizing StarBoard Lit orange: Error has occurred (5) USB Cable Used to connect the StarBoard with the PC. (6) Reflective Frame Reflects light. Used to capture pen or finger operations. English...
  • Page 18: Function Area

    The function area is provided with shortcut keys for the functions that are frequently used in the StarBoard Software. Use by clicking the middle of the symbol with your pen or finger. With the exception of touch mode/pen mode selection and one-time right click, you can customize the shortcuts with the software for Windows.
  • Page 19: Electronic Pen (Option)

    StarBoard FX-E90W Introduction 1.3.3 Electronic Pen (option) Battery cover Open the cover when inserting or replacing the battery. Refer to page 2-4 in this User's Guide for details. Side buttons Mouse Operations assigned to these buttons.Refer to page 2-6 in this User's Guide for details.
  • Page 20: Setup Method

    Furthermore, be sure to install using a wall-mounting bracket capable of supporting a weight of at least 30 kg. [1] Install of Wall-mounting bracket Find the height of board installation, and install the Wall-mounting bracket on a wall. Wall-mounting bracket included in StarBoard((2) of page1-2) 84mm Approx. Wall-mounting bracket Wall-mounting bracket Five parts screwed.
  • Page 21 StarBoard FX-E90W Introduction [2] Install the board CAUTION Be sure to use two or more people for this work. Failure to comply may cause the board to fall, resulting in personal injury, or may cause damage to this product due to shock of impact.
  • Page 22 StarBoard FX-E90W Introduction [3] Settle the board Fix the four corners of board and fitting metal of center of lower board on a wall with screws. Use 3mm diameter screws. Digitiser Storage Area Use 4-6mm diameter screws. Important Be sure to hung the board as digitiser storage area should be located left side.
  • Page 23: Equipment Connection Method

    (2) Connect the opposite side of the RGB cable to the PC's RGB connector, and fasten with screws. (3) Connect the USB cable from the lower left of the StarBoard to a USB port on the PC. (4) Connect the power supply cables of the PC and projector to the power supply.
  • Page 24: How To Use

    StarBoard FX-E90W How to use 2. How to Use 2.1 How to Use Touch Mode This section gives a basic description of how to use the board in touch mode. 2.1.1 Character Input To input characters, use your finger or the stylus that was provided with the product.
  • Page 25: Pc Operations

    StarBoard FX-E90W How to use - Using your finger Extend your finger and touch the board. In the same way as the stylus pen, if you touch the board with anything other than your finger or you are too close to the board, it might cause an incorrect operation.
  • Page 26 StarBoard FX-E90W How to use CAUTION Do not strike the board forcefully with the stylus pen, bend it, or apply an excessive load to it. Failure to comply may result in damage to the stylus pen or personal injury. Important Do not place the stylus pen onto the Reflective Frame .
  • Page 27: How To User The Electronic Pen

    StarBoard FX-E90W How to use 2.2 How to User the Electronic Pen This section gives a basic description of how to use the electronic pen (option). 2.2.1 Inserting the Battery Perform the preparations for using the electronic pen. CAUTION Be sure to install batteries correctly.
  • Page 28: Using The Electronic Pen

    StarBoard FX-E90W How to use 2.2.2 Using the Electronic Pen To use the electronic pen to draw characters or images, place the tip of the electronic pen on the board and then move the pen. When you release the tip of the electronic pen from the board, the writing is complete.
  • Page 29: Basic Operations Of The Electronic Pen

    Software Toolbar Pen tip * The assignment of the side button can be changed by selecting "MENU" on the StarBoard Software toolbar → "Settings" → "StarBoard" → "StarBoard Settings" → "Configure pen buttons" (This function can only be changed in Windows.)
  • Page 30: Start Method

    (5) Select "Start" → "All Programs" → "StarBoard Software," or double-click the StarBoard icon on the desktop. If the "No connection" icon in below appears on the Tasktray, it means that the StarBoard is not connected. Make sure that the StarBoard and the PC are properly connected.
  • Page 31: Start Method (Mac Version)

    StarBoard FX-E90W How to use If the positions of the pen tip and cursor are out of alignment, select "MENU" on the StarBoard Software toolbar → "Settings" → "StarBoard"→ "Calibrate," and then perform position alignment. Important Conduct sensor adjustments upon first-time operations and whenever the board has been moved.
  • Page 32 StarBoard FX-E90W How to use If the positions of the pen tip and cursor are out of alignment, select "MENU" on the StarBoard Software toolbar → "Settings" → "StarBoard" → "Calibrate," and then perform position alignment. Important Conduct sensor adjustments upon first-time operations and whenever the board has been moved.
  • Page 33: Appendix

    USB hub. ・USB extension cable ・Bus-powered USB hub ・USB extender Is a high-speed USB Be sure to connect the StarBoard and Touch Sensor Error device connected to the any high-speed USB devices to (Insufficient USB host controller used separate USB host controllers.
  • Page 34 Other than the above Contact a support center. The position cannot be Have the StarBoard and Adjust the position of the StarBoard aligned properly. projector been placed in the and the projector. If undue correction proper orientation? is performed, it may not be possible to align the position properly.
  • Page 35 (For details on battery replacement, electronic pen may be low. see page 2-4 of this User's Guide.) StarBoard Software files Uninstall the StarBoard Software and may be broken or then re-install it. installation may not be (For details on installing StarBoard complete correctly.
  • Page 36: Adjusting The Sensor

    StarBoard FX-E90W Appendix 3.2 Adjusting the Sensor NOTICE Using infrared and compact cameras, this product captures the image (shadow) of a pen or finger and detects the corresponding coordinate position. Do not operate near lighting that will obstruct the capture of the image.
  • Page 37 StarBoard FX-E90W Appendix [2] "Camera Adjustment Wizard Start" window appears. Press "All Adjust." [3] Press “Finish” This completes sensor adjustment. After making adjustments, check that input can be performed normally. English...
  • Page 38: Sensor Adjustment Procedure (Mac Version)

    [1] Press the "OK" button on the "LSaDrv Touch Sensor Error" dialog box displayed on the Mac screen. [2] Start the sensor adjustment wizard. Start "Go" → "Applications" → "StarBoard" → "Lsadrv" folder → "LsCamWiz." [3] The sensor adjustment wizard starts. Click the "All adjust" button. English...
  • Page 39 If an error such as the following appears, click the "OK" button and then perform adjustment again while referring to Section 3.2.1. If adjustment is still not successful, the StarBoard unit may be defective. [5] If adjustment was successful, click the "Exit" button.
  • Page 40: Regularly Auto Sensor Adjustment (For Windows)

    [1] Confirmation message of auto sensor adjustment will be displayed after 7days as default passed from first connect of StarBoard to PC. If you press “Yes”, auto sensor adjustment program will execute. If you press “No”, this will not execute.
  • Page 41 Confirm the normal input after adjustment * In case of adjustment error, following window will be displayed. Press “Retry” to auto sensor adjustment program execute again. If this message displayed again, StarBoard may have some problem. Please Contact our support. English...
  • Page 42: System Specifications

    StarBoard FX-E90W Appendix 3.4 System Specifications Item Specification Model name StarBoard FX-E90W Detection method Infrared image sensor system Digitiser resolution 0.05mm Sampling rate Approx. 100 points/second when using (USB1.1 Full Speed) Interface USB 1.1 (cable length:5.1 m) Approx. 90inches Effective screen size (mm) 1,939(W)×1,212(H)
  • Page 43: Proper Care And Cleaning

    ・Never use a solvent such as thinner. ・ Note that rubbing or striking the StarBoard surface with a finger nail or other hard object may result in scratching. (2) Cleaning the silver surfaces of the reflective frame ・...
  • Page 44: Product Warranty Policy

    StarBoard FX-E90W Appendix 3.7 Product Warranty Policy 1. During the free warranty service period, if a malfunction occurs during normal use, the malfunction will be corrected without charge, according to the provisions of the warranty. Furthermore, if the customer registration card accompanying the warranty is not returned to our company, the customer information will not be registered;...
  • Page 45 StarBoard FX-E90W Appendix (8) In the event of a malfunction in this product caused by the connection to this product of equipment other than the equipment specified by our company. (9) In the event that there is no abnormality in this product, but a defect in a part other than this product was detected or remedied.

Table of Contents