Download
Share
Print this page
  1. Manuals
  2. Brands
  3. CERES Manuals
  4. Toy
  5. F3B
  6. User manual

CERES F3B User Manual

Hide thumbs
1
2
3
4
5
6

Advertisement

Quick Links

Download this manual
CERES F3B
Wingspan
Area
Aspect ratio
Airfoil
V-tail span
V-tail area
V-tail aspect ratio
V-tail airfoil
Weight
Wing loading
Set contains:
-
Fuselage with canopy and installed towing hook
-
Wings with joiner and servo covers (horns already glued)
-
V-Tail with joiners (horns already glued)
-
Cables for wing servos with connectors (2x 85cm, 2x 30cm)
-
Extension cables for wing servos into the fuselage with connectors (4x 27cm)
-
Two pair of MPX 6-pin connectors
-
Servo holders for wing servos with third BB (2x right, 2x left) - Futaba S3150
-
Servo holder for V-Tail servos into fuselage – Graupner DS3728/DS3781
-
Servo covers
-
Two carbon tubes for V-Tail linkage
-
M3 metal clevises (8x) with M3 screw rods (4x) for wing linkage
-
M2 metal clevises (2x) with 80mm 2mm/M2 wire (2x) for V-tail linkage
-
M2 ball pivot (M2) with 130mm 2mm/M2 wire (2x) for V-Tail linkage
-
10pcs brass ballast cubes (16x20x50mm – 130g/1pcs)
3050mm
2
59,4dm
15,66
DP
586mm
2
5,64dm
6,1
DP
2100 ÷ 3400g/3600g (with lead ballast cubes)
2
35 ÷ 57/60g/dm

Advertisement

loading

Summary of Contents for CERES F3B

  • Page 1 CERES F3B Wingspan 3050mm Area 59,4dm Aspect ratio 15,66 Airfoil V-tail span 586mm V-tail area 5,64dm V-tail aspect ratio V-tail airfoil Weight 2100 ÷ 3400g/3600g (with lead ballast cubes) Wing loading 35 ÷ 57/60g/dm Set contains: Fuselage with canopy and installed towing hook...

  • Page 2: Assembly Manual

    Assembly manual: You will need these accessories: - 4x Futaba S3150 for Ailerons and Flaps - 2x Graupner DS3728 for V-Tail (or Graupner DS3781) - 4cells Sanyo RC-2/3SC (1200mAh, Ni-Cd) - Receiver (min. 6ch) Wing: Solder together the cables and MPX connectors for wing servos. We recommend don’t use any soldering fluid.
  • Page 3 Install the servo into the servo holder. Put two small trust plates to the servo holder. Bolt the trust plates with four small screws. Put together the linkage for ailerons and flaps. Two M3 metal clevises and M3 screw rod. The metal clevis at ailerons servo must be modified (see the picture). After completing, set-up and trimming glue the clevises with Loctite or CA glue.
  • Page 4 Fuselage and V-tail: Glue into the fuselage servo holder for V-Tail servos. Install the servos. Use 8mm servo arms. Put together the V-Tail linkage. Abrade (about 50mm) the 2mm wires before you glue them into the carbon tubes (better stability). Glue the balls (from ball pivot) with Loctite onto V-Tail horn wire.
  • Page 5 Put into the fuselage the linkage leading. Put trough the fuselage wire for antenna before this operation. Take away the V-Tail from fuselage. Make a antenna extension from 0,3-0,8mm wire (1m) and plastic tube (1m). Bend the plastic tube with the wire to this form (see the picture). Solder the antenna extension with antenna wire in fuselage.
  • Page 6 Glue into the fuselage (nose) about 40-60g lead to make recommended C.G. C.G.: 110-112mm Towing hook: 108-110mm...