upcom UC-120-FWA Assembly Manual

Hide thumbs

Table Of Contents

Quick Links

Download this manual

UPCOM

UC-120-FWA

ASSEMBLY MANUAL

UPCOM TECHNOLOGIES INC.

Table of Contents

Summary of Contents for upcom UC-120-FWA

Page 2: Manual Applicability
UPCOM without written consent, and that right is granted to disclose or so use any information on said document.
Page 3: Warning
WARNING The system containers should be unpacked and inspected at the earliest date to insure that all material ♦ has been received and is in good condition. Any damage to materials while in transit should be immediately directed to the freight carrier. He will ♦...
Page 4: Table Of Contents
| TABLE OF CONTENTS Table of Contents Contents Notice Manual Applicability Symbols WARNING Getting Started Antenna Asembly Antenna Pointing Maintenance Specifications...
Page 5: Getting Started
Getting Started If you need help UPCOM and its distributors stand by every product sold . If you need help please contact your local dis- tributor or UPCOM directly at: +1.408.329.4158 or by e-mail: support@upcom.com Manual Updates From time to time, new versions of software may require slight changes to the material presented in this document.
Page 6: Antenna Asembly
| UC-120-FWA ASSEMBLY MANUAL Antenna Asembly Caution: During the assembly procedure, the sequence of instructions must be followed. Do Not Tighten Any Hardware Until Instructed . Refer to the antenna assembly parts list and the steps shown below.
Page 7 UC-120-FWA ASSEMBLY MANUAL | Remove the antenna base from packaging and place it over the floor as showed in the picture...
Page 8 | UC-120-FWA ASSEMBLY MANUAL Open the antenna base and secure the nuts to the base...
Page 9 UC-120-FWA ASSEMBLY MANUAL | The antenna Azimuth and Elevation (AZ&EL) mount...
Page 10 | UC-120-FWA ASSEMBLY MANUAL Insert the antenna AZ&EL mount on top of the base and secure the nuts...
Page 11 UC-120-FWA ASSEMBLY MANUAL | Remove the reflector pieces from transport case and place the pieces side by side...
Page 12 | UC-120-FWA ASSEMBLY MANUAL Lock the latches to secure the reflector pieces together...
Page 13 UC-120-FWA ASSEMBLY MANUAL | Place and secure the reflector on the AZ&EL support with 4 nuts...
Page 14 10 | UC-120-FWA ASSEMBLY MANUAL Insert and tighten the nuts and bolts that secure the reflector pieces...
Page 15 UC-120-FWA ASSEMBLY MANUAL | 11 Attach and secure the feed rods and feed support to the reflector...
Page 16 12 | UC-120-FWA ASSEMBLY MANUAL Install and secure the feed on the feed support assembly...
Page 17: Antenna Pointing
UC-120-FWA ASSEMBLY MANUAL | 13 Antenna Pointing The 1.2 meter reflector contains a 22.6° elevation offset look angle. Therefore, when the reflector aperture is perpendicular to the ground, the antenna is actually looking 22.6° in elevation. Step 1: Place an inclinometer on the reflector support.
Page 18: Maintenance
It is only necessary to inspect for any physical damage done by vandalism or very severe weather conditions. Should any damage be detected to a portion of the reflector, contact the Customer Service Department at UPCOM for recommendations involving reflector repair. MOUNT AND REFLECTOR SUPPORT STRUCTURE The mount and reflector support structure supplied with this antenna is of aluminum construction and has a painted finish.
Page 19: Specifications
UC-120-FWA ASSEMBLY MANUAL | 15 Specifications Electrical Specifications Frequency (GHz) Receive = 10.7 - 12.75 / Transmit = 13.75 - 14.50 Antenna Gain at midland, dBi ( +/- 0.2 dB ) Receive = 41.7 / Transmit = 43.2 IESS 601STDG...
Page 20 16 | UC-120-FWA ASSEMBLY MANUAL Environmental Specifications 25 mph(40km/h) Operational(No Ballast) 30 to 45 Wind Loading mph(72km/h) Operational(With Ballast) 60 mph(145km/h) Survival(With Ballast) Operational = -40° to 140°F(-40° to 60°C) Survival = -50° Temperature to 160°F(-45° to 70°C) Rain(Operational) 1/2”/hr (12mm/h) Radial Ice(Survival) 1/2”/hr (12mm/h)