Factor IR-KIT-36K Installation Instructions page 2

Hide thumbs

page of 3

/ 3
Bookmarks

Enlarged version

(1) IR-CONN-BLK IR CONNECTING BOX

Features and Characteristics

Four emitter output connections



Status power receptacle with LED indicator



Power receptacle with LED indicator



Removable connector for quick connections



Includes mounting/adhesive for wall mounting



Installation

Power:

Connect a 12V DC 500mA power supply to the power jack.

2.1mm + Tip – sleeve. The green LED will be illuminated when powered. This will

power all of the IR components connected to the system.

Status Power:

12VDC 200mA 2.1mm + tip –sleeve. Connecting a power supply

to this connection will power the status connection. The green LED will

illuminate when powered. This can be from a 12 volt trigger output or from a wall

type power supply plugged into a switched outlet of a stereo receiver.

System Connection:

Connect the IR repeaters to the detachable connector

printed V+ (12VDC), G(Ground), and IR (Signal).

Emitter Outputs:

Choosing compatible parts such as IR-1-FLASH or IR-2-FLASH (single or dual IR

emitter), connect up to 4 emitters to the emitter jacks marked 1-4. Place the

emitters directly onto the source equipment's IR sensors (up to 8 units).

Mounting:

Mount /adhere IR-CONN-BLK near the source equipment that the emitters are

attached to.

(2)IR-REP-36/56K IR RECEIVER

The dual-band 38 KHz & 56 KHz IR employs a DSP circuit that is designed

specifically for installation near Plasma, CFL or EMI devises and eliminates

inferences.

Specifications & Features:

Carrier Frequency: 38K + 2K and 56K + 2K Hz.



The standard version of 3 – conductor color-coded cable leads accommodating



the connections of V+, G & IR with a DSP circuit is designed to block plasma,

EMI noise sources.

2M of cable length from main module to bare lead are provided



Typical Control Range: 38 KHz up to 50 feet and 56 KHz up to 30 feet indoor



on axis, depending on remote strength and ambient interference and 15 to 20

feet in direct sunlight.

Reception Angle: Up to 20 foot distance for + / – 45 degree off axis.

LED display:



Activity LED: When the IR signal is received the from remote controller the

Blue LED lights to confirm the IR signal completed the circuit with a

terminator or an Emitter.

IR Lens: rejects visible light interference.



Preinstalled with the black frame 1 extra pc of each white and silver



frames have been included to match the surround of the TV or display.

Dimension: 63(L) x 11(W) x 10(H) mm



Power Requirement: DC 12V, (500~1200mA), Using a regulated adaptor is



recommended

CODE COMPATIBILITY:

38KHz (BR) - CODE

NEC Code

RC5 Code

RC6 Code

RCMM Code

r-step code

RCS-80 Code

R-2000 Code

RCA Code

Sharp Code

Sony 12-bit Code

Sony 15-bit Code

Sony 20-bit Code

Zenith Code

High Data Rate Code

XMP code

◆

Grundig code

NOTE:

◆ Suitable for this IR code

(3) IR-2-FLASH DUAL BLINKING EMITTER

SPECIFICATION & FEATURES:

Oval shape & ultra-compact size



Infrared is built in a transparent housing



Includes 10' cable length / With 3.5mm mono standard plug



Includes self-adhesive tape for quick and easy mounting to any hard, clean &



dry surface / Status indicator

NOTE:

Make sure mounting surface is clean and dry for best results.



Connections of IR emitters directly to power supply's or battery's is not



recommended!

Factor Electronics

www.factorelectronics.com

56KHz(DX) - CODE

◆