Table of Contents
Advertisement
D
UAL
T
P
D
B
HE
ANTHER
UAL
,
OF CUTTING FLAT
LEVEL
DEATH MAY RESULT IF THIS PRODUCT IS USED FOR PURPOSES OTHER THAN DESIGNED
A
NY OTHER USE OF THIS MACHINE VOIDS THE MANUFACTURER
RESPONSIBILITY OF THE OWNER SHOULD ANY DAMAGE OR INJURY OCCUR
I
T IS THE RESPONSIBILITY OF THE OWNER
2501 A
816-884-4444
B
LADE
I
NSTRUCTION
WARNING!
R
C
LADE
OOF
UTTER IS MANUFACTURED TO BE USED FOR THE SOLE PURPOSE
,
-
,
BUILT
UP ROOFS
FOR THE RE
CONVEY EXPLICIT INSTRUCTION TO EACH USER
P
P
ANTHER
RODUCTS
R
., H
NACONDA
D
.
WWW
PANTHERPRODUCTS
R
C
OOF
UTTER
M
ANUAL
-
ROOFING PROCESS
'
S WARRANTY
/
OPERATOR TO UNDERSTAND AND
C
ORPORATION
, MO 64701
ARRISONVILLE
.
800-283-8627
US
. S
ERIOUS INJURY OR
.
,
AND IS THE SOLE
.
.
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Panther DUALBLADEROOFCUTTER
Summary of Contents for Panther DUALBLADEROOFCUTTER
- Page 1 LADE UTTER NSTRUCTION ANUAL WARNING! ANTHER LADE UTTER IS MANUFACTURED TO BE USED FOR THE SOLE PURPOSE OF CUTTING FLAT LEVEL BUILT UP ROOFS FOR THE RE ROOFING PROCESS ERIOUS INJURY OR DEATH MAY RESULT IF THIS PRODUCT IS USED FOR PURPOSES OTHER THAN DESIGNED ’...
- Page 2 LADE UTTER NSTRUCTION ANUAL Published by Panther Products Corporation, Inc. 2501 Anaconda Rd. Harrisonville, MO 64701 www.pantherproducts.us Copyright © 2009, Panther Products Corporation PRINTED IN THE UNITED STATES OF AMERICA...
-
Page 3: Table Of Contents
12” CARBIDE STANDARD (BLD122) CUTTING WIDTH: 25” (WILL ACCOMIDATE 14”) (BLD121) ENGINE: HONDA 20 HP ELECTRIC START CYCLONE AIR CLEANER (DEN701) HYDROSTATIC TRANSAXLE: 2000-016B (AX204) HEADLIGHT: (LGT100) HOUR METER: (MET100) Copyright © 2009, Panther Products Corporation, Harrisonville, MO Page: 3... -
Page 4: Operator Preparation
When operating perpendicular to the edge, a warning line must be ten feet from the roof edge. For specific information on warning lines, the use of guard rails and motion stopping safety systems, refer to OSHA Law. Copyright © 2009, Panther Products Corporation, Harrisonville, MO Page: 4... -
Page 5: Hoisting Machine To Roof
(see below). Do not attach hoist cable to any other part of this machine as damage or injury may result. Use a lifting hook with a safety catch. Lifting Ring Copyright © 2009, Panther Products Corporation, Harrisonville, MO Page: 5... -
Page 6: Safety Precautions
Maintain visibility at all times. Stop if visibility is obstructed. The owner or operator must see that name plates, warnings, are in place and legible. Write to Panther Products Corp. for replacement decals and instructions. Avoid deck cutting. Use only with perimeter warning line system in place. -
Page 7: Pre-Operating Checklist
— Air cleaner should be cleaned daily by lightly tapping it against a hard surface. — Belt guards should be in place, secured properly and tightly. WARNING: UNNING SAW WITHOUT BELT GUARDS PROPERLY IN PLACE WILL VOID THE WARRANTY Copyright © 2009, Panther Products Corporation, Harrisonville, MO Page: 7... -
Page 8: Controls
Forward handle speed adjustment = Controls the top speed, the forward handle will allow the dual blade roofcutter to travel. Parking Brake = Keeps machine from vibrating into forward or reverse when in idle mode Copyright © 2009, Panther Products Corporation, Harrisonville, MO Page: 8... - Page 9 LADE UTTER NSTRUCTION ANUAL Copyright © 2009, Panther Products Corporation, Harrisonville, MO Page: 9...
-
Page 10: Machine Operation
Over greasing the main shaft bearings can cause damage to the seals, drastically reducing bearing life. - The transaxle is completely self contained. No service is required other than maintaining cleanliness of the cooling fins. Copyright © 2009, Panther Products Corporation, Harrisonville, MO Page: 10... - Page 11 (E) 1 on the front wheel mount The two main shaft bearings should be maintained according to the instructions proceeded by the bearing manufacturer. Roof Cutters run in a high contamination environment. Copyright © 2009, Panther Products Corporation, Harrisonville, MO Page: 11...
- Page 12 Replace immediately to avoid possible engine damage. If service or repair of your engine is needed, contact an authorized engine service center. You will need the model, and serial number of your engine, Panther Products Corporation does not cover the engine, which is covered by a separate warranty directly from the engine manufacturer.
-
Page 13: Decals
DCL315 Decal Choke-fast-slow-off 1per DCL406 Decal Passed Inspection 1per DCL320 Decal counter clockwise 1per DCL402 Decal blade guard caution 2per DCL403 Decal belt size 3VX425 2per DCL401 Decal Clockwise 1per Copyright © 2009, Panther Products Corporation, Harrisonville, MO Page: 13... -
Page 14: We Care About Your Safety
ANUAL WE CARE ABOUT SAFETY Safety is important to Panther Products. Be sure to have up-to-date instructions and decals for all Panther Products. The instructions should stay with the product as well as the decals. Any Panther Product you have that does not have the instructions or readable decals,... -
Page 15: Replacing Belts
Replace belts, 4 Gates super HC 3VX425 and reinstall and tighten the above in the reverse order. NOTE: All 4 belts must be replaced as matching sets from one manufacturer. Belt alignment = within 1/16” Copyright © 2009, Panther Products Corporation, Harrisonville, MO Page: 15... -
Page 16: Parts Diagrams
LADE UTTER NSTRUCTION ANUAL Copyright © 2009, Panther Products Corporation, Harrisonville, MO Page: 16... - Page 17 LADE UTTER NSTRUCTION ANUAL Copyright © 2009, Panther Products Corporation, Harrisonville, MO Page: 17...
Need help?
Do you have a question about the DUALBLADEROOFCUTTER and is the answer not in the manual?
Questions and answers