Summary of Contents for Blade CG02 GB
- Page 1 ® CG02 GB 3-Axis Brushless Camera/ Gimbal Instruction Manual Bedienungsanleitung Manuel d’utilisation Manuale di Istruzioni...
- Page 2 NOTICE All instructions, warranties and other collateral documents are subject to change at the sole discretion of Horizon Hobby, LLC. For up-to-date product literature, visit horizonhobby.com and click on the support tab for this product. Meaning of Special Language The following terms are used throughout the product literature to indicate various levels of potential harm when operating this product: NOTICE: Procedures, which if not properly followed, create a possibility of physical property damage AND a little or no possibility of injury.
- Page 3 Safety Precautions and Warnings • Always keep a safe distance in all directions • Never operate your model with low transmitter around your model to avoid collisions or injury. This batteries. model is controlled by a radio signal subject to in- •...
-
Page 4: Table Of Contents
Replacement Parts ..........12 Routing the Wiring ........... 8 Service Contact Information ........13 Connecting the Gimbal ..........9 Box Contents A. CG02 GB 3-Axis Camera /Gimbal D. 3-wire signal lead B. Mounting plate E. 2-wire power lead C. (3) M2.5 x 10 F. -
Page 5: Technical Specifi Cations
Technical Specifi cations Dimensions LxWxH (with lens): 3.00 x 101.62 x 129.12mm Weight: 163 g Working Voltage: Wireless Frequency Range: 5745MHz–5825MHz Lens Sensor: Angle of view: 155° Controlled Rotation Range: Pitch Axis Control: –90°–0° Effective Pixels: 16 million White Balance: Automatic Focusing System: Fixed... -
Page 6: Gimbal Components
Gimbal Components Front Bottom Mounting rails Micro SD card slot Camera lense WiFi antenna Left side Right side YUNEEC satellite PWM ports receiver port 12V gimbal UART code power port update port... -
Page 7: Installing The Mounting Plate
M2.5 x 10 screws. Do not overtighten. IMPORTANT: The CGO2 GB requires the use of the Blade 350 QX2 body set and tall landing gear. If you wish to install the CGO2 GB on a 350 QX, you must fi rst install BLH7811A (body set) and BLH7815TGA (tall landing gear). -
Page 8: Routing The Wiring
Routing the Wiring There are two leads included with the CGO2 GB gimbal: • 3-wire signal lead with a servo style connector and a 3-pin JST connector. • 2-wire power lead with a 4-pin balance connector and a 2-pin JST connector. Route the leads as follows: 1. -
Page 9: Connecting The Gimbal
Connecting the Gimbal 1. Connect the signal lead to any of the 3 available Right side PWM ports PWM ports on the right side of the gimbal assembly. 2. Connect the power lead to the 12V gimbal power port on the left side of the gimbal assembly. Left side 12V gimbal power port... -
Page 10: Transmitter Programming
Transmitter Programming Transmitter control of the pitch angle of the CG02 GB To change the gimbal angle BEFORE starting the is possible with most 6-channel and above Spektrum motors for fl ight, set switch A to position 1. The transmitters. Control of the pitch angle in fl ight is throttle stick will now control the angle of the gimbal. -
Page 11: Using The Gimbal
2. Place the quadcopter on a fl at and stable surface. is ready to connect via WiFi. Ensure there are no obstructions in the path of the CG02 GB. See the “Using the CGO2 App” section for instructions on how to connect your gimbal to your smart device 3. -
Page 12: Using The Cgo2 App
Using the CGO2 App • With the CGO2 GB powered on, open the Wi-Fi CGO App Controls settings on your smartphone or tablet and Remaining SD card capacity Start/Stop recording button connect to the CGO2 GB network (CGO2 GB_******) using the password 0.00 G “1234567890”. -
Page 13: Troubleshooting
Troubleshooting Problem Possible Cause Solution The gimbal vibrates after Gimbal did not initialize correctly Re-initialize with the gimbal clear of switching ON or was obstructed obstructions Keep the quadcopter and gimbal level Gimbal does not respond to Gimbal did not initialize and immobile for 5 seconds after control input switching ON... -
Page 14: Service Contact Information
Service Contact Information Country of Horizon Hobby Contact Information Address Purchase Horizon Service Center servicecenter.horizonhobby.com/ (Repairs and Repair Requests) RequestForm/ www.quickbase.com/db/ Horizon Product Support United States 4105 Fieldstone Rd bghj7ey8c?a=GenNewRecord (Product Technical Assistance) of America Champaign, Illinois, 61822 USA 888-959-2304 sales@horizonhobby.com Sales 888-959-2304... - Page 15 ©2014 Horizon Hobby, LLC. Blade is a registered trademarks of Horizon Hobby, LLC. Yuneec is a trademark of Yuneec International Co., Ltd. All other trademarks, service marks or logos are property of their respective owners. Patents pending. Created 12/14 46791.1 BLH8110...
Need help?
Do you have a question about the CG02 GB and is the answer not in the manual?
Questions and answers