14) The treadmill must be unfolded during use and only folded again at the end of use with elevation back to 0. 15) This machine is only intended for domestic use. Do not use this GoFit Platinum Treadmill in any commercial, rental, or institutional setting.
Replace defective components immediately and keep the equipment out of use until repair. For repairs, use only original spare parts and when in doubt, ask GoFit Platinum for advice. Only one person is permitted to use this treadmill at the same time.
BEFORE YOU BEGIN Thank you for selecting the revolutionary GoFit Platinum Treadmill. The GFTMP01 offers an impressive array of features to make your home workouts more enjoyable and effective. For your benefit, read this manual carefully before using the GoFit Platinum Treadmill.
Page 6
MOTORIZED TREADMILL PRE-ASSEMBLY Handrail control button and heart rate strap are optional items in the package 1) Heart rate can be measured on this treadmill. Attach strap to chest during exercise, the heart rate value will display on the PULSE window. 2) In addition to using the control button on the console, the control button on the handrail can also be used to adjust speed and elevation.
ASSEMBLY STEPS CAUTION! Please follow the assembly steps below carefully and exactly to aviod injury . ALWAYS ASSEMBLE THE TREADMILL WITH AN ASSISTANT, DO NOT ATTEMPT ASSEMBLY BY ONESELF. STEP ONE Pull out the Control Wire with Guide Thread in the right Upright (C) and cap it into the inside hole in right Upright.
Page 8
STEP THREE After left and right Uprights are tightened, cap left and right Decoration Covers (G, H) to the Frame and tighten them with Screw (c). STEP FOUR After finishing assembly according to above steps, assemble left and right Handrail Cover (R) (F) and Handrail Cover (L) (E) to the Handrail.
Page 9
CAUTION > The cylinder contains high pressure gas. Precautions must be taken to avoid it crashing into other objects > If the cylinder is hit, it may cause damage and make the use not smooth. When the user is folding the treadmill, it may result in the falling of the frame and cause injury.
Page 10
MAINTENANCE 1. Centering the Walking Belt. If the Walking Belt tracks off center to the right or left of the deck, first turn the power off. Then use a wrench to tighten the rear roller bolt on the side of the treadmill toward which the belt is moving.
COMPUTER INSTRUCTION Start Display: 1) If the SAFETY KEY is taken off, the matrix screen will display key picture (as the picture below) and each function window will display ----. If the SAFETY KEY is replaced,the matrix screen will display KGS (mile) for avoirdupois unit and the preset value is 70KG(150LBS).
Page 12
2) During working, the beeper will make a sound for warning if the safety key works off, then the treadmill will stop working. At this moment, put the safety key back to the recess of console, and all the values will turn back to the initial values. 3) If you don’t hold the Hand Pulse Sensor in general Start/Ready position, the PULSE window will display HP.
Page 13
IV. General Operation and Instruction: MANUAL Mode 1. When press Start, it will begin to count down for 3 seconds, after that, the motor will start , the speed will start at 1.0KPH. The matrix window goes contra rotate like along playground, every circle is 0.4KM (0.25MIL).
Page 14
P5 interval LEVEL: pre-set1; range1~10; step 1 Time: pre-set30min; range20~99min; step 1 min P6 rolling LEVEL: pre-set1; range1~10; step1 Time: pre-set30min; range20~99min; step 1 min P7 Weight loss LEVEL: pre-set1; range1~10; step 1 Time: pre-set30min; range20~99min; step 1 min P8 Racing Program 1.
Page 15
P11HRC Distinguish as 65%、75%、85%、THR (Target Heart Rate) This function must be attached with heart beat to finish. Dot Matrix window displays HRC. The program aims to exercise heartbeat. When operating, the heartbeat value is equal to the pre-set value, the angle and speed will keep steady to maintain the heartbeat value in certain range to achieve the exercising effect.
Page 16
E1:The treadmill can’t read the speed value. E6:In the range of ADC, incline motor doesn’t run. E7:Incline is too height or too low (exceed the range). ** If it has any error signal, please contact GoFit Platinum. E6 / E7 ◆...
Page 17
(Drawing 1) B. When the incline angle of treadmill is on low position (as drawing 2). At this time you should press STOP and hold it tightly, then press UP at the same time. Hold the two keys for 3~5 seconds simultaneity and the incline motor will force the treadmill ascend the incline height.
Page 30
Trainings hints: With buying this treadmill you have taken the first step toward improving your fitness. With the help of this item you can add value to your life with improved health, wellbeing and lifestyle. Goal of training: Building of muscles General fitness Endurance Feeling of wellbeing...
Page 31
Training: Warming up should be done with every sporting activity to decrease the risk or injury. A suggested warm up is a 5-10 minute run on the spot or around the room with a few jumps at each minute interval. Stretching: The following stretches are gentle but effective in waking up your body, stimulating your circulation and making your ankles more flexible.
Need help?
Do you have a question about the GFTMP01 and is the answer not in the manual?
Questions and answers
I need the gofit platinum safety key