Summary of Contents for TerraTec PBG6E
- Page 1 PBG6E 6” BENCH GRINDER ACL Group (Intl) Ltd Email: eusales@terratekintl.com www.terratekintl.com User Manual — Please read and retain for future reference...
-
Page 2: Table Of Contents
Contents Parts List Technical Information Safety Instructions Using Your Tool Maintenance And Cleaning Warranty Parts List Description Description Rotor Grinder Wheel Stator Screw Screw Nameplate Middle ring Eye shield Bracket Cover Washer Spring washer Right Inner guard Winding Wheel flange Eye shield Bearing Nameplate of wheel... -
Page 3: Screw
Description Description Screw Right outer guard Washer Screw Capacitor Square Neck Screw Screw Right tool rest Plug & Cable Left Inner guard Tooth washer Washer Knob nut Left Outer guard Screw Left tool rest Screw Screw Switch Cable adaptor Ground terminal Screw Tooth washer Cable Block... - Page 4 Exploded Assembly Diagram NOTICE: Actual product may vary from pictures shown. ACL Group (Intl) Ltd Email: eusales@terratekintl.com www.terratekintl.com...
-
Page 5: Eye Shield
1 ON/OFF switch 2 Eye Shield 3 Eye Shield Mount 4 Wheel Guard 5 Grinding wheel 6 Workpiece support fastening screw 7 Workpiece support 8 Mounting holes 9 Foot 10 Eye Shield adjustment screw ACL Group (Intl) Ltd Email: eusales@terratekintl.com www.terratekintl.com... - Page 6 Bench Grinder Model PGB6E Rated voltage: 230 V ~ 50 Hz Power rating: 150 W S2 30 min Idle speed n : 2950 min Grinding wheel diameter: 150 mm Grinding wheel thickness: 16 mm Grinding wheel hole diameter: 12.7 mm Weight N.W./G.W.: 6 /7 kgs Protection category: I Load factor:...
- Page 7 Read this entire manual before using this product. Failure to do so can result in serious injury. Save this manual for future reference. Copyright© 2013 by ACL Group (Intl) Ltd. All rights reserved. This manual or any artwork contained herein must not be reproduced in any shape or form without the express written consent of ACL Group (Intl) Ltd.
- Page 8 Read and Keep This Manual Please read carefully all instructions within this manual. Failure to follow all safety warnings can result in serious personal injury. The term “Power Tool” in all of the following warnings refers to your mains operated (corded) or battery operated (cordless) power tool This symbol is to warn you of potential personal injury hazards.
-
Page 9: Electrical Safety
Electrical safety Before use, ensure that the power outlet you are using matches the plug on your power tool and that the voltage of the outlet matches that of your power tool. Only use grounded extension cords with power tools fitted with proper plugs and if using outdoors ensure any extension cord is suitable for outdoor use. - Page 10 WARNING: For your own safety read Instruction Manual before operating your tool. A) Eye protection required. B) Keep hands away from grinding wheel. C) Do not operate without guards in place. D) Do not perform any operation freehand. E) Never grab wheel while it is turning. F) Turn off tool and wait for tool to stop before moving workpiece or changing settings.
- Page 11 - Make sure of your footing. Avoid abnormal working positions. - Keep electric tools out of the rain. Never use electric tools in wet or damp conditions, and never use them near flammable liquids. - Keep the power cable safe from damage. Oil, solvent and sharp edges can damage cables. - Keep your workplace tidy.
- Page 12 Special safety instructions 1. Before you begin to work with the grinding machine, carry out an acoustic test on its grinding wheel (if a grinding wheel is in good condition it will produce a clear tone when tapped, e.g. with a plastic hammer). It is also important to perform this test when fitting new grinding wheels (risk of damage in transit).
- Page 13 Power Extension Cords When using any extension cord the machine will suffer a power reduction due to the drop in voltage caused by the length of the cord. This can be partially offset by selecting extension cords with lower gauge wire. Check all extension cords for damage before use.
-
Page 14: Proper Use
Using Your Tool Proper use The double grinder is a multi-function tool for the rough and precision grinding of metals, plastics and other materials using a selection of grinding wheels. The machine must only be used for its intended purpose! Even if the machine is used as intended, certain residual risk factors cannot be completely eliminated. - Page 15 Fitting The Eye Shields Fit the Eye shield (3) to the wheel safety guards using the Eye shield adjustment screw (10). Adjusting The Eye Shield Adjust the Eye Shield Mount (3) using the adjustment screw (10) so that the distance between the dry grinding wheel (5) and the Eye Shield mount (3) is as small as possible and DOES NOT exceed 2 mm.
- Page 16 Fitting The Work Piece Supports Undo the fastening screws (6). Secure the work piece supports (7) to the double wheel grinder using the fastening screws (6). Adjusting the workpiece supports Adjust the workpiece supports (7) using the fastening screws (6) so that the distance between the dry grinding wheel (5) and the workpiece support (7) is as small as possible and certainly does not exceed 2 mm.
-
Page 17: Changing The Grinding Wheel
Changing The Grinding Wheel Remove the 3 screws (A) holding the side section of the Wheel Guard (B) and remove the Wheel Guard. Undo the nut (D) (Important: The left grinding wheel is fastened with a left-handed thread and the right grinding wheel with a right-handed thread), by holding the nut of the grinding wheel mount on the opposite side, remove the flange (C), and replace the grindingwheel (5). -
Page 18: Maintenance And Cleaning
Grinding We recommend that you use the fine-grained grinding wheel for fine grinding work and the coarse-grained grinding wheel for coarse grinding work. Place the work piece onto the work piece support (7) and slowly guide the work piece towards the grinding wheel (5) at the desired angle to the point where the work piece and grinding wheel make contact. -
Page 19: Environmental Protection
We ACL Group (Intl.) Ltd, England DN6 8LZ declare that the Bench grinder has been manufactured according to our full quality assurance procedures. The declaration is to certify that it conforms to CE, EMC, LVD, MD and RoHS directives: EN55014-1/A1: 2009 EN55014-2/A2: 2008 EN61000-3-2/ A2: 2009 EN61000-3-3: 2008... - Page 20 Warranty Please read the following carefully ACL Group (Intl) Ltd. and/or it’s distributor has provided the parts list and assembly diagram as a reference tool only. Neither ACL Group (Intl). Ltd. or its distributor makes any representation or warranty of any kind to the buyer that he or she is qualified to do any repairs or replace any parts of this product.
- Page 21 ACL Group (Intl) Ltd Email: eusales@terratekintl.com www.terratekintl.com...
Need help?
Do you have a question about the PBG6E and is the answer not in the manual?
Questions and answers