Summary of Contents for Pacific Digital PDCdrive
- Page 1 Installation Manual BEFORE CALLING PACIFIC DIGITAL TECHNICAL SUPPORT, PLEASE COMPLETELY READ THE INSTALLATION SECTION OF THIS MANUAL...
- Page 2 Having trouble with your PDC Drive? Want to know more about how it works? Check the list of common questions provided in this manual; you may find the answers you need. If you don’t, or if the problem persists, Please visit Pacific Digital online at www.PacificDigital.com...
- Page 3 “Windows” and “Windows NT” are registered trademarks of Microsoft Corporation (U.S.) in the U.S. and other countries. Pacific Digital Corporation herewith declares that it will not be liable in any way for any loss of data or any other damage, whether direct or indirect, caused by the operation or malfunctioning of this product.
-
Page 4: Table Of Contents
Table of Contents Model and Serial Number Parts and Functions Getting Started IDE / ATAPI Drive Installation Settings and Connections Connecting the PDC Drive Connecting the Cables Bundled Software Bundled Software Continued Handling Guide Handling Guide Continued Handling Discs Troubleshooting Notes and Information... -
Page 5: Model And Serial Number
Model and Serial Number Product Model & Serial Number are located on top cover of your CD- RW drive, or on the side of your retail box. (Example Label May Vary) (Example Label) Please write down the PDC serial number from the top of the PDC drive or the side of the PDC box. -
Page 6: Parts And Functions
Parts and Functions Front Panel 1. Operation indicator lamp 2. Manual eject hole Used to manually eject the tray in an event when it will not open normally. 3. Open/close button 4. Shutter or tray Rear Panel 1. AUDIO output connector For connecting the internal audio cable. -
Page 7: Getting Started
Getting Started PACKAGE CONTENTS Drive 40 Pin IDE cable for IDE drive Burner bundle software & Blank Audio cable CD-R disk... -
Page 8: Ide / Atapi Drive Installation
Unpack the drive and contents. Included is a PDC Burner Bundle software disc, one blank CD-R disc, an audio cable and the IDE data cable. NOTE: Keep your Pacific Digital CD-RW drive in it’s Anti-Static bag until Step 7. Step 2: Record your drive information on page 18 of this manual. -
Page 9: Settings And Connections
Settings and Connections Connection example Most computer motherboards have two IDE interface connectors: a Primary and a Secondary. You can connect a total of four units to the motherboard: one Master and one Slave IDE unit to the Primary and Secondary connector. We recommend connecting the PDC drive as Secondary Master. -
Page 10: Connecting The Pdc Drive
Connecting the PDC Drive Mounting screw holes are located in four places on the right and left panels of the PDC drive. When securing the PDC drive into a computer secure the PDC drive firmly in place with the four mounting screws included in this kit: NOTE: Only use the screws included in the PDC kit. -
Page 11: Connecting The Cables
Connecting the cables... -
Page 12: Bundled Software
The following programs are supplied on the PDC Burner Bundle. Pacific Digital supports the “Recording Mastering Software” only. All other softwares included are either “Trial” or “Lite Versions”. Pacific Digital will not support any “Trial” or “Lite Version” software included on the “PDC Burner Bundle”. For support on these softwares please contact their respective manufactures. -
Page 13: Bundled Software Continued
Bundled Software Continued MusicMatch (lite version) – (Audio Jukebox) (Supported by MusicMatch www.musicmatch.com) ?? Make your own CDs from your MP3s. ?? Turn your music collection into MP3s. ?? Play MP3s, CDs and Windows Media. ?? Tune into MUSICMATCH Radio. ?? Manage your digital music collection. -
Page 14: Handling Guide
Handling Guidelines This section explains the handling guidelines for Media. MEDIA INSERTION AND REMOVAL Step 1: To insert the CD-ROM, CD-R or CD-RW disc, press the eject button. Note: The disc surface must be clean and the label should be facing upward, also make sure that blue side is down. -
Page 15: Handling Guide Continued
Handling Guidelines Continued Step 2: Once the disc tray has fully extended, place the CD-ROM, CD-R or CD- RW disc into the center of the tray. Press the eject button to have the drive accept the CD-ROM, CD-R or CD-RW disc. Step 3: The busy lamp will light for a few seconds to indicate that a disc has been loaded and the drive has accepted the disc. -
Page 16: Handling Discs
Handling Discs Handling CD-R/RWs and other CD discs. Do not place in the following locations: Hot or humid locations or where they will be exposed to direct sunlight. Locations susceptible to significant differences in temperature. Handling notes: Do not soil or damage them. Do not drop or bend them. -
Page 17: Troubleshooting
Troubleshooting When this occurs Possible cause Is the computer on? Tray fails to open: Has the power supply cable been connected correctly? Has the label of the media peeled off? Tray fails to close: Has the disc been inserted correctly? Has the drive’s master/slave jumper pin been set correctly? Computer fails to work:... -
Page 18: Notes And Information
Notes and Information During installation, record the following information. This information will be needed to contact technical support. You can contact PDC Technical Support at (888) 999- 0732 or by fax (949) 252-9397. When calling the Technical Support Department, MAKE SURE TO HAVE THE FOLLOWING INFORMATION READILY AVAILABLE, BECAUSE IT IS NECESSARY IN ORDER TO RECEIVE TECHNICAL SUPPORT. - Page 19 Pacific Digital Corporation (PDC), Consumer Products Division 2052 Alton Pkwy, Irvine, CA. 92606 www.PacificDigital.com 1862-32-02-9...