Summary of Contents for APPENDIX High speed dome camera
- Page 1 Intelligent High Speed Dome Installation Manual Version：V1.02 Before using the product, please carefully read the manual and the maintenance of this manual for future use...
- Page 2 Appendix 4 After-Sales Service Promise Dear Users: Thank you for your confidence to our company brand. To make you feel more efficient, convenient and comfortable to our products, our company makes the following servicing promises: 1. Quality Warranty The flashing arrow in the symbol is used to remind The products are complied with the requirements of purchase-sale the user, the large non-insulated "dangerous...
-
Page 3: Table Of Contents
45(13) 71(21) 181(55) Fault Analysis ..................43 25(7) 41(12) 65(19) 164(49) Appendix 1 Lighting-proof, with Surge-protector......... 44 Appendix 2 RS485 Bus Common Sense ..........45 23(7) 37(11) 59(17) 150(45) Appendix 3 Line and Transmission Distance Table....... 46 21(6) 34(10) 55(16) 139(42) Appendix 4 After-Sales Service Promise.......... -
Page 4: Safety Announcement
Safety Announcement Installation Steps Please read the manual carefully before the installation; 1. Wall Mount Installation Steps: Shall be subject to all the warnings； 1）position for digging hole on the wall, and install expansion screw. Shall comply with all instructions and the manual; Make the cover parts guide line through the bracket to the wall bracket, To avoid failure, please use the recommended accessories;... -
Page 5: Attentions
Appendix 1 Lighting-proof, with Surge-protector Attentions Don’t expose the camera to rain or moisture (except outdoor This product adopts air discharge lightning and TVS board-level technology; can used model) effectively prevent damage to equipment from 1500W (below) instantaneous It is designed inside of the house, so be sure to avoid rain and moisture. -
Page 6: Functions And Features
Functions and Features Fault Analysis Attention：Some operation need to restart dome. 1. Built-in decoder Failures Possible reason Resolution Digital design, data will not be lost while power fails. Voltage exchange With recovery, function while turning on the users can run it as you like. Support 200 presets, 4 preset patrolling scanning routes, each contains 24 No action and no damaged... -
Page 7: Special Use For Preset Point
4. Built-in OSD Menu Technical Specifications Built-in multi-functional video OSD, functional parameters of cameras and P/T function can be settable, with easy operation. Set 16 main subjects display Electrical indicator Built-in direction display Power DC12V/3A ±10% Voltage ≤25W Settings： Protocol Pelco-P/D selectable Baud rate selectable... -
Page 8: Dome Installation
Dome Size and Bracket Installation Size Information Display Figuration Dome Size (As picture 1) Various information display time could be set through this menu. MAIN MANU DISPLAY CONFIGURATION 【SYSTEM SETTING】 → DOME TITLE PRESETS TITLE 【CAMERA PARAMETERS】 ZOOM POSITION 【PANTILT SETTING】 DIRECTION INDICATOR GLOBAL SETTING 【DISPLAY CONFIGURATION】... -
Page 9: Installing Preparation
HOME ACTION Installing Preparation From the time when the machine gets no any commands: if it still receives no any orders at the set time, the dome camera will automatically execute one function set by the users of the “Leisure Time 1. -
Page 10: Installation Steps
Under 【PANTILT SETTING】choose【AUTOSCAN SETUP】and press Installation Steps 【OPEN】for confirming. Under 【AUTOSCAN SETUP】press 【AUTOSCAN NUMBER】for entering into the auto scan number change setting and the parameter will 1. Wall Mount Installation Steps: flicker. 1）position for digging hole on the wall, and install expansion screw. Up/down P/T for setting. -
Page 11: Dome Setting
Safety Announcement Dome Setting Please read the manual carefully before the installation; Shall be subject to all the warnings； System Connection Shall comply with all instructions and the manual; 1) Dome System Chart (as picture 5) To avoid failure, please use the recommended accessories; Use the indicated power supply line and voltage；if the location of power and voltage is not clear, please contact with the dealer；... -
Page 12: Dip Switch Settings
enter the patrol number change setting and the parameter flicker. DIP Switch Settings Up/down P/T to choose. Press【OPEN】for confirm, save and exit; press【CLOSE】 exit directly. Baud rate Setting SW2（B7~B8） EDIT SEQUENCE Operations: Call preset point 95 to enter main menu. Up/Down cursor to choose【... - Page 13 Under 【 】choose【 】menu, PANTILT SETTING PRESETS SETTING press【OPEN】for Address Setting SW1 confirm. Under 【 】choose【SET NEW PRESET】for PRESETS SETTING entering into the preset point setting. Users could head the middle position right to the preset position by controlling Press【OPEN】for confirm, save and exit; press the dome camera.
- Page 14 This function could make the dome camera record the current level angel, hade angel and lens multiple parameters and so on. The camera could turn to this position quickly if it is required. It could support 200 preset points. Preset Number Setting Operations: Call preset point 95 to enter main menu.
- Page 15 SET NORTH DIRECTION If execute this function, the system will automatically save the current position of the dome camera as the north direction of it, and it will be regarded as the zero point of direction, i.e. 0° level position.. Operations Call preset point 95 to enter main menu..
- Page 16 auto-aperture while using auto-focus or auto-aperture, with only using 2. Line Connect Instruction: the rocker. Control line mark as picture 7. Focus：After choosing this item, it will just return to auto-focus mode while Color Instruction using manual-focus or manual-aperture, with only using the rocker. DC IN DC12V Aperture：After choosing this item, it will just return to auto-aperture mode...
-
Page 17: Basic Function Operation Settings
Pantilt setting Basic Function Operation Settings MAIN MENU PANTILT SETTING 【SYSTEM SETTING】 → 【PANTILT SETTING】 This operation and editing regulations just take our company control system as an 【PRESETS SETUP】 【CAMERA PARAMETERS】 example, different keyboard manufacturers in the main menu to call the dome and 【SEQUENCE SETUP】... - Page 18 up-menu or some item when it is dome menu edit, and save edit value Under 【CAMERA PARAMETERS】choose【PRIVACY_MASK】item, after programming. press【OPEN】for confirm and enter privacy area set item. 【FAR】Far focus, means focused far images. Under 【PRIVACY_MASK】choose【MASK ACTIVATE】item, press 【NEAR】Near focus, means focused near images. 【OPEN】enter ON/OFF Privacy Zone setting.
-
Page 19: Menu Hint
When the dome is vertical down≥45°,this function can’t work, as Menu Hint bellow： SYSTEM SETTING → DOME ID TITLE LANGUAGE ENGLISH CHANGE PASSWORD FACTORY DEFAULT SYSTEM RESTART SYSTEM INFOMATION MAIN MENU Privacy Area Set CAMERA PARAMETERS Operations： 【SYSTEM SETTING】 Call preset 95 to enter main menu. →【LENS PARAMETER】... -
Page 20: Main Menu Function Setting
Operations: Main Menu Function Setting Under 【 】 to choose 【 】 CAMERA PARAMETERS BACKLIGHT MODE and press【OPEN】to enter BLC mode set. Main menu: Up/Down PT to modify BLC value and open/close this function. 【SYSTEM SETTING】 Press 【 OPEN】 key, save and exit; press 【 CLOSE】 key, exit directly. 【CAMERA PARAMETERS】... - Page 21 Operations： TITLE SETTING: Under 【 】 choose 【 R Gain】 item, press 【 OPEN】 Operations： WHITE BALANCE for confirm and enter red gain set item, Call preset 95 to enter main menu. Up/down P/T to change red gain value, range from 0~255 the Up/down cursor choose item, press【OPEN】...
- Page 22 Through this function can set various white balance mode （auto Up/down cursor choose【SYSTEM SETTING】item, press【OPEN】 for and manual）,as well as red gain and blue gain adjustment. confirm, enter system setting menu. Under【SYSTEM SETTING】to choose【CHANGE PASSWPRD】item, CAMERA PARAMETERS WHITE BALANCE Press【OPEN】for confirm, enter password modification setting, and “Input 【LENS PARAMETER】...
-
Page 23: Camera Parameter
Attention: Only under (Manual) and (Iris ) mode, it is available. Camera Parameter Menu are different from factories, please follow the associated one. MAIN MENU CAMERA PARAMETERS BRIGHT LEVEL Operations： 【SYSTEM SETTING】 →【LENS PARAMETER】 Under【EXPOSURE MODE】choose【BRIGHT LEVEL】item, press 【 】 【EXPOSURE MODE】... - Page 24 Up/down cursor choose light should pass so that the image can be clear. And pass-ray exposure with 【 CAMERA PARAMETERS 】 item, press 【OPEN】for confirm and enter【LENS PARAMETER】menu. time (shutter speed decide), Qualcomm light area (aperture size decide). Under 【LENS PARAMETER】to choose【DIGITAL ZOOM】item, press The quality of image associated with gain and brightness settings, and 【OPEN】for confirm and enter electronic zoom set, parameter flickers.
Need help?
Do you have a question about the High speed dome camera and is the answer not in the manual?
Questions and answers