Subscribe to Our Youtube Channel
Summary of Contents for Lafalink LF-R500
-
Page 1: User Guide
300Mbps Outdoor Wireless Bridge/WISP User Guide （ideal for LF-R800） Version：V2.0.0... - Page 2 Specifications are subject to change without notice. is a registered trademark of LAFALINK TECHNOLOGIES CO., LTD. Other brands and product names are trademarks or registered trademarks of their respective holders. No part of the specifications may be reproduced in any form or by any means or used to make any derivative such as translation, transformation, or adaptation without permission from LAFALINK TECHNOLOGIES CO., LTD.
-
Page 3: Fcc Statement
FCC STATEMENT This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. -
Page 4: Ce Mark Warning
uncontrolled environment. This device and its antenna must not be co-located or operating in conjunction with any other antenna or transmitter. “To comply with FCC RF exposure compliance requirements, this grant is applicable to only Mobile Configurations. The antennas used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter.”... - Page 5 National Restrictions 2400.0-2483.5 MHz Country Restriction Reason/remark General authorization Bulgaria required for outdoor use and public service Military Radiolocation use. Refarming of the 2.4GHz Outdoor use limited to 10 band has been ongoing in France mW e.i.r.p. within the band recent years to allow current 2454-2483.5 MHz relaxed regulation.
-
Page 6: Package Content
Package Content The following items should be found in your package: One 300M Wireless CPE LF-R500 One 12V1A Power Adapter One PoE Injector One Mounting Kits One Quick Installation Guide Note： Make sure that the package contains the above items. If any of the... -
Page 7: Table Of Contents
Contents Chapter 1 Product Review......................8 1.1 Overview of the Product....................8 1.2 Features..........................8 Chapter 2 Hardware Installation..................10 2.1 LED Explanation......................10 2.2 Interfaces and button....................10 2.3 System Requirements....................11 2.4 Environment Requirements..................11 Chapter 3 Connecting the Device..................12 3.1 Connecting the Device....................12 Chapter 4 Wireless Mode..................... -
Page 8: Chapter 1 Product Review
Chapter 1 Product Review Thank you for choosing LF-R500 2.4GHz High Power Wireless Outdoor CPE 1.1 Overview of the Product The LF-R800 2.4GHz High Power Wireless Outdoor CPE is dedicated to Outdoor wireless network solutions. The LF-R800 2.4GHz High Power Wireless Outdoor CPE will allow you to connect your network with other wireless devices wirelessly, sharing Internet Access, files and fun, easily and securely. - Page 9 Supports passive power over Ethernet. Supports Wireless Distribution System (WDS). Supports Remote Management Output transmit power adjustable. Supports PPPoE, Dynamic IP, Static IP Internet Access. Built-in NAT and DHCP server supporting static IP address distributing. ...
-
Page 10: Chapter 2 Hardware Installation
Chapter 2 Hardware Installation 2.1 LED Explanation LF-R500 consists of several LED indicators, which is designed to indicate connections and wireless signal. View from left to right, the parts are explained below. Status Indication Power Off No Power Wireless Turn On... -
Page 11: System Requirements
Reset: Press and hold the RESET button for at least 10 seconds, and then the AP reboots after the LED at the rightmost in Figure 2-1 flashes. LAN: This port is used to connect to the POE port of the provided Power Injector. ... -
Page 12: Chapter 3 Connecting The Device
Chapter 3 Connecting the Device 3.1 Connecting the Device To establish an infrastructure network in AP Client Router mode as Figure 2-3, please take the following steps: 1. R800 supports PoE supply power, it can not use the power adapter insert directly. So first connect the computer and LAN port of PoE Injector. - Page 13 The instructions in this section will help you configure each of your PCs to be able to communicate with the AP. The default IP address of the LF-R500 2.4GHz High Power Wireless Outdoor CPE is 192.168.1.1. And the default Subnet Mask is 255.255.255.0. These values can be seen from the LAN.
- Page 14 5) The following TCP/IP Properties window will display and the IP Address tab is open on this window by default. Now you have to configure the TCP/IP protocol below: Setting IP address automatically Select Obtain an IP address automatically, Choose Obtain DNS server automatically, as shown in the Figure below:...
- Page 15 Open your web browser and enter the IP address of the AP (192.168.1.254) and a login screen will display (shown in Figure 3-3). Enter admin for Username and Password (both in lower case letters) on the following login screen.
- Page 16 Click OK or press Enter of your keyboard, and the management page will display.
-
Page 17: Chapter 4 Wireless Mode
Chapter 4 Wireless Mode The AP supports three mode operation modes for multi-user to access the Internet: Gateway, Bridge, and Wireless ISP Mode. In Gateway Mode, the AP can connect to the DSL/Cable Modem and access the Internet, other devices can share the wireless network ... -
Page 18: Chapter 5 Gateway Mode
Chapter 5 Gateway Mode In Gateway Mode，you must need the Internet Service first，CPE can use three ways to connect the Internet: PPPoE, Dynamic IP, Static IP, and then setup a wireless network, others wi-fi device can share the Internet connection. Here we have steps to complete the setup: Choose the Operation Mode, Setup the WAN type, LAN setting, and Wireless Setup. - Page 19 1. PPPOE If you choose PPPoE, you should enter the following parameters as shown: Enter the User Name and Password provided by your ISP. These fields are case-sensitive. 2. Static IP If you choose Static IP, you should have fixed IP Parameters specified by your ISP. For example: IP Address：212.197.17.56 Subnet Mask：255.255.255.0...
- Page 20 Enter the IP address in dotted-decimal notation provided by your ISP. 3. Dynamic IP If you choose Dynamic IP, the router will automatically get IP parameters from your ISP. （2） Wireless Setting When connect the wireless is successful , you also can establish a wifi network localy, and setting the wireless ssid and security of it.
-
Page 21: Chapter 6 Bridge Mode
Chapter 6 Bridge Mode Here we using two LF-R500 and make the second CPE bridge the first one’s wireless singals. CPE 1 LF-R500 Setting: Mode：Gateway（Internet access through ADSL） IP address：192.168.1.1 DHCP： 192.168.1.5~192.168.1.100 SSID: LAFALINK Wireless Key：LAFALINK Connect the computer and CPE 2 LF-R500 LAN port. And then open the web，... - Page 22 DHCP function in this mode by default. You can setting the IP Address to 192.1.1.x manualy. （2）Wireless Connect Setting Click the ‘connect setting’ and click the ‘scan ap’. The CPE will research the wireless network automatically. Choose the Wireless SSID is ‘LAFALINK’, and then enter the wireless key: LAFALINK.:...
- Page 23 To avoid the IP conflict of the CPE and the wireless router, LF-R500 local address should be set to 192.168.1.2 manually （2） Wireless Setting When connect the wireless is successful , you also can establish a wifi network locally, and setting the wireless ssid and security of it.
-
Page 24: Chapter 6 Wireless Isp Mode
Chapter 6 Wireless ISP Mode In WISP Mode，you must need the WISP Service first，CPE can use three ways to connect the Internet: PPPoE, Dynamic IP, Static IP, and then it can setup a wireless network, others wifi device can share the Internet connection. Here we have three step to complete the setup: Connect the Wireless ISP, Setup the WAN type, LAN setting, and Wireless Setup. - Page 25 There are three Connection type for Internet access: Dynamic IP/Static IP/PPPoE), you are not sure which connection type you use currently, please contact your ISP to obtain the correct information. 4. PPPOE If you choose PPPoE, you should enter the following parameters as shown: Enter the User Name and Password provided by your ISP.
- Page 26 Subnet Mask：255.255.255.0 Gateway：212.197.17.254 DNS1：202.96.128.68 DNS2：202.96.134.133 Enter the IP address in dotted-decimal notation provided by your ISP. 6. Dynamic IP If you choose Dynamic IP, the router will automatically get IP parameters from your ISP. （2） Wireless Setting When connect the wireless is successful , you also can establish a wifi network locally, and setting the wireless ssid and security of it.
Need help?
Do you have a question about the LF-R500 and is the answer not in the manual?
Questions and answers