Active forever VibraLITE 3 VL300 Quick Reference

VIBRATION WATCH with:
Vibration Alarm
won't disturb others.
Beep Alarm option
Auto Reload Countdown Timer
can be set for seconds, minutes &
hours. Use for reminders such as
medical conditions, medication,
timing presentations or procedures,
parking, cooking. Will
automatically reload to preset
countdown time.
Electro-Luminescent backlight
For viewing display at night
Second Clock great when traveling
in a different time zone.
Two Alarm Settings use for daily
reminders, wake up, snooze,
medication
Hourly Alert/Chime Option
12 or 24 Hour clock
Stopwatch
OPERATING MODES
Your watch has six operating
modes:
To go from one operating mode to
another, repeat pressing the MODE
button for each mode to be
displayed. The operating modes
will rotate in the order as listed
above.
TO BECOME FAMILIAR WITH
THE OPERATING MODES &
THEIR SYMBOLS, ROTATE
THROUGH EACH MODE BY
PRESSING THE 'MODE"
BUTTON.
FIRST TIME SETTING OF
YOUR CALENDAR/CLOCK
(You must have this set for your
Alarm Settings to be accurate.)
When setting the Calendar &
Clock, the rotation for setting is
Seconds, Hour, Minutes, 12/24Hr,
Date, Month, Day of Week.
ONLY when the digits are
BLINKING can you set or change
the setting. The clock will stop
blinking when no button is pressed
for two minutes. You cannot
switch to another mode of
operation while the display is
blinking. To exit and stop the
blinking, push LAP/RESET button.
1. Repeat pressing the MODE
button until the CALENDAR
CLOCK operating mode shows
on the display.
2. Press & Hold the LAP/RESET
button until the second's digits
begin to BLINK.
Press the START/STOP button
to reset the second's display to
00 00.
00 00
3. Press the MODE button. The
hour digits will begin to
BLINK.
Press the START/STOP button
to rotate to correct hour of the
day.
WHEN IN THE 12 HR MODE,
A PM INDICATOR WILL
APPEAR ON THE DISPLAY
ABOVE AND LEFT OF THE
HOUR DIGITS. AS YOU
ROTATE TO 12 HOURS THE
PM MUST SHOW FOR
SETTING CORRECT TIME
FOR AFTERNOON OR
EVENING. BE SURE TO SET
CORRECTLY FOR THE
CURRENT TIME OF DAY.
4. Press the MODE button to go to
the minute digits. The minute
digits will begin to BLINK.
Press the START/STOP button
to rotate to the correct minute.
5. Press the MODE button and the
12H or 24H will show and
BLINK on the display. Press the
START/STOP button to change
from 12H to 24H or from 24H
to 12H.
6. Press the MODE button for the
date of the month. A number
will BLINK at the top left
corner of the display. Press the
START/STOP button to rotate
to the correct date of the month.
(1 - 31)
7. Press the MODE button for the
Month. A number will BLINK
on the display. Press the
START/STOP button to rotate
to the current month of the year.
(Example; 6 for Jun, 9 for Sept)
8. Press the MODE button for the
Day of the Week. A two-letter
abbreviation at the top of the
display will BLINK. Press the
START/STOP button to rotate
to the correct day. (Example TU TU TU TU
for Tuesday; TH TH TH for Thursday) TH
9. Press the LAP/RESET button
when you have finished the
correct set up. The display will
stop blinking.
HOW TO SET AN ALARM
CLOCK (Setting procedure is the
same for BOTH alarms)
1. Repeat Pressing the MODE
button to rotate to the alarm
operating mode you want: A1 A1 = A1 A1
1st ALARM or A2 A2 = 2ND
A2 A2
ALARM.
2. Press & Hold the LAP/RESET
button until the hour digits
BLINK.
Press the START/STOP button
to rotate to the hour wanted.
Note: In the 12 12 12 12 Hr Hr Hr Mode, Hr
remember to use the PM PM PM PM
indicator for correct setting.
3. Press the MODE button to go to
the minutes. The minutes will
BLINK. Press the
START/STOP button to rotate
to the minute wanted.
4. Press the LAP/RESET Button
when finished. The display will
stop blinking. The set icon will
show on the display. Your alarm
is set.
When A1 Alarm is set the icon
shows beside the PM PM indicator PM PM
under Alm1 Alm1 Alm1 Alm1.
When A2 A2 Alarm is set the icon A2 A2
shows on the display beside the
A1 A1 A1 A1 icon under Alm2 Alm2 Alm2. Alm2
Note: Calendar Clock Time must
be set for Alarm Time activation
to be correct.
HOW TO TURN ON AND OFF
THE HOURLY ALERT
Note: Hourly Alert is a short single
reminder
1. Repeat Pressing the MODE
button and select either 1st
ND
ALARM=A1 or 2
ALARM=A2
2. Repeat Pressing START/STOP
button until the Hourly Alert
indicator (located beside the
Alm2 indicator) shows on the
display. Hourly alert is on when
icon shows. Hourly alert is off
when icon doesn't show.
ON/OFF SETTINGS OF
ALARMS
Note: To turn on or off First Alarm
you must be in the A1 A1 A1 A1 mode.
To turn on or off Second Alarm
you must be in the A2 A2 mode. A2 A2
Repeat Pressing the MODE button
to show alarm you wish to turn
off or on: 1ST OR 2ND ALARM.
Repeat Pressing the START /STOP
button to rotate, alarm on (hourly
alert) & alarm off. When Icon(s)
shows, alarm is set. Alarm is off
when icon does not show. (See
previous illustration)
HOW TO ACTIVATE OR
DEACTIVATE VIBRATION
AND BEEP FUNCTION
1. Repeat Pressing the MODE
button to the CALENDAR
CLOCK mode.
2. Repeat Pressing the
START/STOP button to rotate
through the selection of settings.
When a function is activated, its
respective icon will be
highlighted, at the top right
corner of the display. Rotation
will be: Vibration ON, Beep
ON, Vibration and Beep ON,
Vibration & Beep OFF. Select
one of the four functions that
you desire.
This can be changed at anytime
by following steps 1 and 2.
Alarm will stop automatically after
approximately 20 seconds. To stop
alarm before the automatic stop,
press any button. NOTE: To check
setting the watch is in at any time,
press the MODE button. With each
press of the button the vibration
and/or beep will respond if set.