Summary of Contents for Elecro Engineering Swimming Pool Heat Pump
- Page 1 Swimming Pool Heat Pump Owner’s Installation & Operations Manual 5005001B Version 2.02...
-
Page 2: Table Of Contents
Page 2 TABLE OF CONTENTS Introduction Installation Location Wind Tie Down Water Plumbing Electrical Hook Up Bonding Water Chemistry Maintenance Heat Pump Features Heat Pump Operation Control On/Off Pool/Spa Modes Changing Set Point Temperature Heater Running Time Keypad Lockout Defrost Cycle Condensate Draining Care &... -
Page 3: Introduction
Page 3 INTRODUCTION Congratulations on purchasing the most advanced high efficiency, microprocessor-controlled pool and spa heat pump available. Your heater has been manufactured with the most state-of-the-art quality control equipment available today to ensure the highest quality product delivered to your door. - Page 4 Page 4 Please be sure to complete and mail in the Warranty Registration Card that is provided in the package with your heater. This card helps us to notify you about new information on your heater. Also, please take a moment and jot down the following information. If you should ever need to call us for service or a question, we will need this information: Model Number:___________________________________...
-
Page 5: Installation
Page 5 INSTALLATION LOCATION The unit is designed for outdoor installation and shall not be placed in a totally enclosed area such as a shed or a garage unless ventilation is provided to ensure adequate air exchange for proper operation. Recirculation of cold discharge air back into the evaporator coil will greatly reduce heating capacity and efficiency of the unit and void the compressor warranty. -
Page 6: Water Plumbing
Page 6 WATER PLUMBING The piping sequence: pool pump / filter / heater / Chlorinator / Pool. In-line chlorinators must be down stream of the heater to minimize harm to the pool equipment. Rigid PVC piping is recommended and all joints should be secured with PVC glue. -
Page 7: Bonding
Page 7 BONDING Because all metals have different electrical potentials, ALL metal and electrical components of the pool system must be bonded together. This includes the metal framework of the pool, lights, pump, filter, heater, any automatic chlorine generator and any other metal or electrical equipment. -
Page 8: Water Chemistry Maintenance
Page 8 WATER CHEMISTRY MAINTENANCE Not only is the water chemistry of your pool or spa important to the health of you and your family, it also directly affects the life of your heater. This is the most important item in the maintenance of the heater. If the water chemistry is improperly maintained or if the chemicals are improperly introduced into the water, this will damage the heater’s internal heat exchanger and could eventually cause a leak, rendering the heater... -
Page 9: Heat Pump Features
Page 9 HEAT PUMP FEATURES CABINET – Your heat pump’s cabinet is made from a maintenance-free, rust-free plastic that is UV resistant. It will last for years and any dirt or dust may simply be wiped away with a cloth or sprayed off with a water hose. -
Page 10: Heat Pump Operation
Page 10 HEAT PUMP OPERATION CONTROL ON/OFF When the unit is powered up, but in the OFF mode, the display will show “OFF”. To turn the unit on, press the Up arrow button until desired temperature is reached. To turn the unit off press and hold the Down arrow button until the display shows off. -
Page 11: Changing Set Point Temperature
Page 11 CHANGING SET POINT TEMPERATURE To change the set point temperature, press either the Up or Down arrow buttons on the control. The display will then show “POOL TEMPERATURE” on the top line and the current set point temperature in numbers on the bottom line. -
Page 12: Care & Maintenance
Page 12 CARE & MAINTENANCE CLEANING There is not much maintenance that needs to be done on your heater. Making sure there is good airflow through the evaporator and proper drainage are the two main tasks. A garden hose with low-pressure water flow can be used to clean the evaporator coil. -
Page 13: Troubleshooting
Page 13 TROUBLESHOOTING A simple test to verify that your heater is functioning is to place your hand above the unit. There should be cool air blowing out the top after time delay has expired. The return water to the pool should be a few degrees warmer than water entering the heater. - Page 14 Page 14 Control Displays Water flow restriction, Clean pump and filter. "HIGH valve is turned Adjust water valves. If REFRIGERANT restricting flow. problem persists, call PRESSURE" factory for service. Control Displays Water flow restriction, Clean pump and filter. "HP3 Water valve is turned Adjust water valves.
-
Page 15: Service
This may save you the cost of a service call. If you still need help, follow the instructions below. Service can be obtained by calling Elecro Engineering Ltd: 01438 749474 When asking for help or service please provide a detailed description of the problem, your heater’s complete model number and serial number, the...
Need help?
Do you have a question about the Swimming Pool Heat Pump and is the answer not in the manual?
Questions and answers