Sharkoon T28 Manual
  1. Manuals
  2. Brands
  3. Sharkoon Manuals
  4. Desktop
  5. T28
  6. Manual
Sharkoon T28 Manual

Sharkoon T28 Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
Manual
T28
1

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the T28 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Sharkoon T28

  • Page 1 Manual...

  • Page 2: Table Of Contents

    10. Installation of an add-on card 11. The pre-installed fans Dear customer! Congratulations for purchasing this premium quality SHARKOON product. For a long life time and to take full advantage of this product we recommend you to read this manual completely.

  • Page 3: Features

    Case front 2x 120 mm LED fans Rear panel 1x 120 mm LED fan 2. Package contents • T28 (3x 120 mm pre-installed LED fans) • Accessory set: Screws for mainboard Screws for PSU mounting Screws for drive mounting Screws for HDD mounting...

  • Page 4: The Case At A Glance

    Note: If you are missing any of the items listed above, please contact our customer service immediately: support@sharkoon.com (Germany and Europe) support@sharkoon.com.tw (international). Mounting rails for HDDs 5.25" bezel with 3.5" opening 3. The case at a glance Front view A –...
  • Page 5 Side view (opened/left) A – Drive bays for 5.25" devices B – Mainboard mounting panel with: a – Installation opening for CPU coolers b – Cable management system Rear view A – Opening for I/O shield B – Pre-installed 120 mm fan C –...

  • Page 6: Installation Notes

    The internal I/O connectors b c d e A – HD audio B – 2x USB2.0 connectors C – Connectors for: a – Power switch b – Power LED – c – Power-LED + d – HDD-LED e – Reset-Switch 4.

  • Page 7: Installation Of A Mainboard

    In order to remove the HDD cages, proceed as follows: 1. Unscrew the thumb screws on the back side of the case and remove both side panels. 2. Press/lift the attachment levers of the HDD cage (fig. 1). fig. 1 3.
  • Page 8 The mainboard contains special screw openings (fig. 3). fig. 3 Place the mainboard to the mounting panel. A stand-off must be screwed into every drilling of the mounting panel visible through the mainboard’s screw openings. 3. Remove the mainboard and screw the stand-offs into the respective drillings of the mounting panel (fig.
  • Page 9 4. Press the I/O shield (delivered with the mainboard) into the I/O shield opening in the case’s back side. 5. Place the mainboard back onto the stand-offs and screw the mainboard to them (fig. 5). (Screws for mainboard mounting) fig. 5 6.

  • Page 10: Installation Of A Psu

    6. Installation of a PSU 1. Set up the case in front of you and put the PSU from the inside against the PSU bracket on the case’s back side (fig. 6). fig. 6 2. Screw the PSU to the case from the outside (fig. 7). (Screws for PSU mounting) fig.

  • Page 11: Installation Of A Hdd

    7. Installation of a HDD 7.1 3.5" HDD cage 1. Remove the case’s right side panel. 2. Attach the mounting rails to the 3.5" HDD from both sides (fig. 8). (HDD mounting rails) fig. 8 3. Slide the HDD with attached mounting rails into an available drive bay inside the 3.5" HDD cage (fig.

  • Page 12: Mounting Frame

    7.2 Mounting frame 1. Take a mounting frame from the HDD cage (fig. 10). (Mounting frame) fig. 10 2. Place an HDD into the mounting frame (connectors pointing backwards / fig. 11a and b). Abb. 11a Abb. 11b...

  • Page 13: Installation Of An Optical Device

    3. Attach the HDD to the mounting frame from below (fig. 12a and b). fig. 12a fig. 12b 4. Slide the mounting frame into the HDD cage until it locks (fig. 13). fig. 13 8. Installation of an optical device 1.
  • Page 14 2. Dismantle the 5.25" front bezel from the mounting bay in which you intend to install the drive by loosening its screws and pushing the bezel to the inside (fig. 15). Remove the quick fasteners (fig. 16). fig. 15 fig. 16 (Carefully take out an optionally present metal bezel covering the 3.5"...

  • Page 15: Installation Of A 3.5" Device

    Note: If you intend to transport the case we recommend securing (additionally) the installed drives. 5. Connect the optical drive to the power supply and the mainboard. (Put the front bezel back onto the case.) 9. Installation of a 3.5" device (1.
  • Page 16 fig. 21 4. Slide the 3.5" device with attached mounting rails into the case’s drive bay (fig. 22) and screw it to the drive bay from both sides (fig. 23). fig. 22 fig. 23 5. Connect the 3.5" device to the power supply and the mainboard. 6.

  • Page 17: Installation Of An Add-On Card

    10. Installation of an add-on card 1. Remove the slot bezel’s fixation screw and take away the slot bezel (fig. 25). fig. 25 2. Insert the add-on card into the mainboard’s respective slot and fix it to the case by re- attaching the fixation screw (fig.

  • Page 18: Sharkoon Technologies

    Legal disclaimer: As a continuing policy of product improvement at SHARKOON, the design and specifica- tions are subject to change without prior notice. National product specifications may vary. All rights reserved especially (also in extracts) for translation, reprinting, reproduction by copying or other technical means.

Table of Contents