Summary of Contents for WyreStorm Digital Integrity MX0404-PP
Page 1
Wyrestorm HDBaseT Lite HD Matrix Part Number MX0404-PP 4 Input / 4 Output single-cable HD Matrix with two-way IR control Instruction Manual Thank you for choosing this Wyrestorm product. Please read these instructions carefully before installing to avoid complications later.
LAN Control – NET CTL iv. EDID DIP Switch settings This MX0404-PP HDBaseT Lite Matrix model allows any connected HDMI inputs to be distributed independently and Advanced Operation simultaneously over distances of up to 70m (230ft) to any of the 4...
Features panel buttons, local IR, IR call-back, RS232 and LAN. learned into a universal remote handset to allow the control of multiple devices from one handset. the box. control system to control display. and integrated RJ45 connectors for a single Cat5e/6/7 UTP cable to each display point for ease of installation* * The inclusion of duplicate HDMI ports essentially doubles the number of outputs (though slaved to the...
Package Contents of instruction manual* *downloadable versions can be found at www.Wyrestorm.com Specifications Operating Temperature 0 to +35°C (32 to +95°F) 1024x768, 1280x1024, Range 1600x1200, 1920x1200 Operating Humidity Range 5 to 90 % RH (no condensation) 480i/576i/480p/576p/720p/ 1080i/1080p Output Bandwidth Signalling Rate HDMI v1.4 with full 3D com- patibility with Frame Sequen-...
Front Panel Mounting brackets Input select button (click to scroll numerically) Input selection per output (lit to show input currently selected for output) IR sensor Power switch 03 02 Rear Panel RS232 port* LAN port* EDID DIP switch (for manual EDID setting) 12v DC power input IR Extension port (IR EXT) UTP Output ports 1 –...
Cable/Satellite 70m/230ft RX-1UTP-IR-70 Mirror of 04 Output 04 Apple TV/Media Server 70m/230ft Cat 5e/6 cable performance HDBaseT Lite range 1080p MX0404-PP with RX-1UTP-IR70 display receiver 16ft 32ft 49ft 65ft 82ft 98ft 114ft 131ft 147ft 164ft 196ft 229ft 262ft 1080p 1080i Cat 5e/6 wiring guide The quality of termination for every RJ45 is essential.
Page 7
Switch on the power to your input sources, displays, and any small sensor. display receivers used. Finally, power up the MATRIX. Your MX0404-PP should now be fully connected and ready for Connect a good quality, well terminated Cat 5e/6/7 cable use.
IR Call-back of Matrix and Source Devices Output port number The MX0404-PP is not only a switcher and extender of multiple HDMI signals to multiple HDMI receivers located remotely, it also passes IR control signals through the IR call-back system to...
IR Receivers at all locations you wish to control from to enable the IR signal to travel both ways via the single Cat5e/6/7 cable. MX0404-PP Single Cat5e/6/7 70m / 230ft HDMI As each IR TX port is allocated to an individual HDMI input port, if the user is unable to establish IR control of the device, care should be taken to check firstly, that the IR emitter and...
4 together for 3 seconds until ALL output LED lights flash, MX0404-PP. However, the following information on advanced signalling the unit is in Two-way IR Mode. operation will detail how the matrix system can be configured and for advanced control and settings can be altered or data manually Repeat the process to disable Two-way IR Mode.
Page 11
Receive Message Window – displays messages received Set IP Button – allows you to set the IP address to be used from the matrix, such as input/output settings and command by the system. selections. You can view the current condition of all input/ Clicking opens a pop-up window in which you can choose to output ports by pressing the let the system automatically detect your IP address, with the...
Page 12
Select the connection settings such as IP address and MAC address of the MX0404-PP, as well as its name if you decide to change the name of your matrix (see Device Name section below). button to check current settings attached to the IR port.
Page 13
0000000000 Enter the default password of ten zeros ‘0000000000’ and click to take you to the matrix controller screen. Assign IP If ‘Assign IP’ is displayed in the dialog box, the matrix has encountered a problem detecting an IP address and manual input of information is required.
EDID DIP Switch settings Distribution of HD signals through the matrix requires mutual 1080p 3D Video / Stereo Audio communication or ‘handshake’ between source and display. If there is any disparity between the two, successful transmission Setting the DIP switch to this position will becomes problematic.
Page 15
Remaining settings no function (reserved for future updates) INPUT Support 1080i stereo Video: 1080i Video and Audio: Video: unsupported Audio: stereo unsupported Audio: stereo OUTPUT Video: 1080i Video: 1080P Video: 1080P Support 1080P stereo Audio: stereo Audio: unsupported Audio: stereo Support 1080P7.1 Audio Video: 1080i Video: 1080P...
12. Troubleshooting Generally, the majority of HD distribution installation Distance – Is your cable too long for the signal to be issues are either caused by minor connection errors, transmitted effectively? HDBT Lite allows transmission of communication problems between devices, or when the 1080p up to 70m (229ft) so make sure you cable distance transmission of high signal bandwidth is attempted using matches your requirements and is well within the maximum...
Page 17
caused by a connection problem between matrix and display If using a graphics-based source (such as a PC/Mac/media – turn off all equipment and swap the signal carrying cables server), make sure the source resolution is set to a maximum of at both ends to ascertain if the cable or termination is at 1080p, 50Hz.
13. FAQs 5e or 6? environmentally friendly. While our equipment is tested and graded to Cat 5e cable standard; tests have shown that better results are achieved Do I need to use 1 or 2 cables? when using Cat6 cable. The lower gauge, thicker copper Using our conventional pro (TMDS) transmission method the cores ensure better signal transfer.
17. Warranty cable mode using the DIP switches. This useful feature uses Should you feel your product does not function adequately due an alternative Equalisation method to re-sync the signal over longer distances. warrantor”) will, for the length of the period indicated below (starting from the original date of purchase) either: I cannot get a signal out from my A/V a) Repair the product with new or refurbished parts.
Need help?
Do you have a question about the MX0404-PP and is the answer not in the manual?
Questions and answers