Subscribe to Our Youtube Channel
Summary of Contents for Cortex SW-10200
- Page 1 User’s Manual SW-10200 PoE+ Switch 802.3at 8 x 10/100 PoE +802.3at plus 2 Gigabit Combo Ports RJ45/SFP Rev. 141022...
- Page 2 User’s Manual: SW-10200 Trademarks Copyright © i3 International Inc. 2012. Contents subject to revision without prior notice. All other trademarks belong to their respective owners. Disclaimer i3 International does not warrant that the hardware will work properly in all environments and applications, and makes no warranty and representation, either implied or expressed, with respect to the quality, performance, merchantability, or fitness for a particular purpose.
-
Page 3: Table Of Contents
User’s Manual: SW-10200 TABLE OF CONTENTS 1. INTRODUCTION ....................5 1.1. Product Overview ....................... 5 1.1.1. Product Features ........................5 2. INSTALLATION ....................7 2.1. Hardware Installation ......................7 2.1.1. Package Contents ........................7 2.2. Hardware Description ......................7 3. SOFTWARE CONFIGURATION ................. 9 3.1. - Page 4 User’s Manual: SW-10200 9. SPANNING TREE PROTOCOL ................ 26 9.2. STP Port Settings ......................27 9.3. Loopback Detection Settings ..................28 10. TRUNKING ...................... 29 11. BACKUP/RECOVERY ..................30 12. MISCELLANEOUS SETTINGS ............... 31 13. TROUBLESHOOTING ..................32 APPENDIX A: NETWORKING HARDWARE ............33 A.1.
-
Page 5: Introduction
User’s Manual: SW-10200 1. INTRODUCTION 1.1. Product Overview This switch provides 8 10/100 Mbps PoE ports, 8 10/100BASE-TX ports that support the IEEE 802.3at PoE protocol, and includes auto MDI/MDIX crossover detection function providing an excellent choice in network flexibility. Each port transmits up to 30 watts, fully configurable from a convenient web UI. With this added PoE feature, this switch is an ideal solution for building wireless, IP surveillance, and VoIP networks. - Page 6 User’s Manual: SW-10200 Mechanical LED Indicator Per Port: Link/ Act PoE Port: Act/Status Per Unit: Power Power Consumption 260 Watts (Max) Power Input 100~240V/AC, 50~60Hz Power Output 48V/DC per Port Output – 30W Max per Port ...
-
Page 7: Installation
Figure 1 - SW-10200 switch 2.2. Hardware Description This section describes the hardware features and installation of the 8 PoE port + 2-port Gigabit Ethernet Combo Web Managed Switch. - Page 8 User’s Manual: SW-10200 LED Indicators The LED Indicators present real-time information of systematic operation status. The following table provides description of LED status and their meaning. Status Description Power Power switch is on Power is off Port Link transmission at 10/100 Mbps...
-
Page 9: Software Configuration
User’s Manual: SW-10200 3. SOFTWARE CONFIGURATION This section describes the software configuration of the SW-10200 switch using the Web Interface. 3.1. Logging In Open a web browser, and enter the address 192.168.0.10 (for switches with the F/W version V141015 or newer) or 192.0.0.20 (for switches with the F/W version V110613 or older). -
Page 10: Administration
User’s Manual: SW-10200 3.2. Administration 3.2.1. Authentication Configuration Clicking on Administrator in the navigation pane will bring up administrative options on the main pane. If this is your first login, change the username and password in the Authentication Configuration section. -
Page 11: System Status
User’s Manual: SW-10200 3.2.3. System Status This page displays basic information about the switch. Figure 9 - An overview of the switch MAC Address: Displays the unique hardware address assigned by manufacturer (default). Number of Ports: Displays number of ports in the switch. -
Page 12: Firmware Update
User’s Manual: SW-10200 which are not covered by the software reset. (1) To activate, press the factory reset button for 5 seconds until the LED begins to blink. (2) The blinking LED signals that the CPU is executing the reset procedure. Release the button. -
Page 13: Port Management
User’s Manual: SW-10200 4. PORT MANAGEMENT Port Management includes Port Configuration, Port Mirroring, Bandwidth Control, Broadcast Storm Control and PoE 4.1. Port Configuration To access port configuration options, click on the link Port Configuration in the navigation pane of the web interface. -
Page 14: Port Mirroring
User’s Manual: SW-10200 Learning. Click Update to save your changes. A table at the bottom of the main pane displays a summary of each port’s configuration. The display shows the following information: Current Status: Displays current port status. Setting Status: Displays current status. -
Page 15: Broadcast Storm Control
User’s Manual: SW-10200 Figure 16 - Bandwidth summary 4.3.1. Broadcast Storm Control The switch implements a broadcast storm control mechanism. Check the ports next to Enable Port to select ports that will drop incoming broadcast packets if the number of received broadcast packets reaches the threshold defined. - Page 16 User’s Manual: SW-10200 Figure 18 - Configure PoE...
-
Page 17: Vlan Setting
User’s Manual: SW-10200 5. VLAN SETTING 5.1. Introduction to VLAN A Virtual Local Area Network (VLAN) is a network topology configured according to a logical scheme rather than the physical location. VLAN can be used to combine any collection of LAN segments into an autonomous user group that appears as a single LAN. -
Page 18: Untagged Vlans
User’s Manual: SW-10200 device to another with VLAN information intact. This allows 802.1Q VLANs to span network devices or even the entire network provided that all network devices are 802.1Q compliant. All physical ports on a switch have a PVID. 802.1Q ports are also assigned a PVID for use within the switch. If no VLANs are defined on the switch, all ports are then assigned to a default VLAN with a PVID equal to 1. -
Page 19: Vlan Member
User’s Manual: SW-10200 Figure 20 - Select options for VLAN On this screen you can now define and configure your Up- and Downlink ports. These are important since here the handover between the switches of your network takes place. VLAN Mode: Displays VLAN mode: port based/Tag based VLAN. Here you can also switch back to Port Based VLAN Mode ... -
Page 20: Multi To 1 Setting
User’s Manual: SW-10200 Add VLAN Groups (identified throughout your network by unique and constant numbers). Start with IDs from 100 and up. Keep in mind that some switches use “1” as the default, while others use “4095” or “4096” as default. -
Page 21: Per Port Counter
User’s Manual: SW-10200 6. PER PORT COUNTER 6.1. Port Counter To access port statistics, click on the link Port Counter in the navigation pane of the web interface. This page provides statistics on each port. Figures are grouped into four categories: Receive Packet & Transmit Packet/ Transmit &... -
Page 22: Qos Setting
User’s Manual: SW-10200 7. QoS SETTING 7.1. About QoS Here you can configure QoS policy priority mode and CoS (Class of Service) configuration. Quality of Service (QoS) is an advanced traffic prioritization feature that allows you to establish control over network traffic. QoS enables you to assign various grades of network service to different types of traffic, such as multi-media, video, protocol-specific, time critical, and file-backup traffic. -
Page 23: 71B7.2.2. Port, 802.1P, Ip/Ds Based
User’s Manual: SW-10200 selected, the traffic will be forwarded according to the number set in each queue. Click Update to save your changes. 71B7.2.2. Port, 802.1p, IP/DS based Note that checking Port Base, VLAN Tag or IP/DS will cause the port checked to be treated as high priority. -
Page 24: Security
User’s Manual: SW-10200 8. SECURITY To access security options, click on the link Security in the navigation pane of the web interface. 8.1. MAC Address Binding Setting a MAC address allows interfaces to be uniquely identified on your network. Figure 27 - Bind MAC addresses to ports ... - Page 25 User’s Manual: SW-10200 Figure 29 - Packet filtering overview Function Enable: Enable or Disable filtering. Port Filtering Rule: To allow forwarding (do not filter) select negative in the drop-down menu and in the Protocol section, select ports to forward. To disallow forwarding (filter) select positive in the drop-down menu and in the Protocol section, select ports to filter.
-
Page 26: Spanning Tree Protocol
User’s Manual: SW-10200 9. SPANNING TREE PROTOCOL The Spanning Tree protocol can be used to detect and disable network loops, and to provide backup links between switches, bridges or routers. This allows the switch to interact with other bridging devices in your network to ensure that only one route exists between any two stations on the network, and provide backup links which automatically take over when a primary link goes down. -
Page 27: Stp Port Settings
User’s Manual: SW-10200 9.2. STP Port Settings Figure 31 - Set options for the port in STP Port No: The port ID. It cannot be changed. Aggregations refer to any configured trunk group. Root Path Cost: This parameter is used by the STP to determine the best path between devices. Therefore, lower values should be assigned to ports attached to faster media, and higher values assigned to ports with slower media. -
Page 28: Loopback Detection Settings
User’s Manual: SW-10200 9.3. Loopback Detection Settings This function detects the presence of network traffic routed back to its source. The status for all ports is given. Figure 32 - Prevent traffic collision by configuring Loopback Detection Loopback Detect Function: Choose whether to Enable or Disable this function. -
Page 29: Trunking
User’s Manual: SW-10200 10. TRUNKING Port trunk allows multiple links to be bundled together and act as a single physical link for increased throughput. It provides load balancing, and redundancy of links in a switched network. As such, the link does not have an inherent total bandwidth equal to the sum of its component physical links. -
Page 30: Backup/Recovery
User’s Manual: SW-10200 11. BACKUP/RECOVERY To access backup and recovery options, click on the link Backup/Recovery in the navigation pane of the web interface. Figure 34 - Manage backup and recovery of switch settings This function provides the user with a method to backup/recover switch configuration. Save a configuration file by clicking Download. -
Page 31: Miscellaneous Settings
User’s Manual: SW-10200 12. MISCELLANEOUS SETTINGS Miscellaneous settings can be used to configure output queue aging time, VLAN stride and IGMP snooping. Figure 35 - Configure Aging time, VLAN striding and IGMP snooping Output queue aging: When a packet is stored in a switch for a long time, it will expire from the allowable time defined by the protocol and become a useless packet. -
Page 32: Troubleshooting
User’s Manual: SW-10200 13. TROUBLESHOOTING This chapter contains information to help you solve issues that might come up while using the switch. The Link LED is not lit Solution: Check the cable connection and remove duplex mode of the Ethernet Switch Some stations cannot talk to other stations located on the other port ... -
Page 33: Appendix A: Networking Hardware
User’s Manual: SW-10200 APPENDIX A: NETWORKING HARDWARE A.1. RJ-45 Pin Assignments 1000Mbps, 1000Base T pin assignment. Contact MDI-X BI_DA+ BI_DB+ BI_DA- BI_DB- BI_DB+ BI_DA+ BI_DC+ BI_DD+ BI_DC- BI_DD- BI_DB- BI_DA- BI_DD+ BI_DC+ BI_DD- BI_DC- Table 3 - Pin assignment for 1000 Mbps, 1000 BaseT Implicit implementation of the crossover function within a twisted-pair cable, or at a wiring panel, while not expressly forbidden, is beyond the scope of this standard. - Page 34 User’s Manual: SW-10200 Straight Cable SIDE 1 SIDE2 SIDE 1 1 = White / Orange 1 = White / Orange 2 = Orange 2 = Orange SIDE 2 3 = White / Green 3 = White / Green 4 = Blue...
-
Page 35: Appendix B: Store-And-Forward
User’s Manual: SW-10200 APPENDIX B: Store-and-Forward Store-and-Forward is one type of packet-forwarding technique. A Store-and-Forward Ethernet switch stores the incoming frame in an internal buffer; complete error checking is done before transmission to eliminate the occurrence of error packets. This is the best choice when a network efficiency and stability are a priority. -
Page 36: Appendix C: Poe Overview
User’s Manual: SW-10200 APPENDIX C: PoE OVERVIEW IEEE802.3af, also called Data Terminal equipment (DTE) power via Media dependent interface (MDI), is an international standard which defines the transmission for power over Ethernet. 802.3af delivers 48V power over RJ-45 wiring. Besides 802.3af, two types of source equipment are defined: Mid-Span and End-Span. -
Page 37: Poe Provisioning Process
User’s Manual: SW-10200 Table 7 - Power supplied over data pins References: IEEE Std 802.3af-2003 (Amendment to IEEE Std 802.3-2002, including IEEE Std 802.3ae-2002), 2003 Page(s):0_1-121 White Paper on Power over Ethernet (IEEE802.3af) http://www.poweroverethernet.com/articles.php?article_id=52 Microsemi /PowerDsine ... -
Page 38: Classification
User’s Manual: SW-10200 C.2.2. Classification Once a PD is detected, the PSE may optionally perform classification to determine the maximal power a PD is to consume. The PSE induces 15.5-20.5 VDC, limited to 100 mA, for a period of 10 to 75 ms responded by a certain current consumption by the PD, indicating its power class. -
Page 39: Appendex D: Glossary
User’s Manual: SW-10200 APPENDEX D: GLOSSARY Aggregation Aggregation is a method wherein multiple ports are used in parallel to increase the link speed beyond the limits of a port and to increase the redundancy for higher availability. Auto-Negotiation Auto-negotiation is the process where two different devices establish the mode of operation and the speed settings that can be shared by those devices for a link. -
Page 40: Igmp Querier
User’s Manual: SW-10200 DNS is an acronym for Domain Name System. It stores and associates many types of information with domain names. Most importantly, DNS translates human-friendly domain names and computer hostnames into computer-friendly IP addresses. For example, the domain name www.example.com might translate to 192.168.0.10. -
Page 41: Mac Table
User’s Manual: SW-10200 MAC Table Switching of frames is based upon the DMAC address contained in the frame. The switch builds up a table that maps MAC addresses to switch ports for knowing which ports the frames should go to (based upon the DMAC address in the frame). -
Page 42: Router Port
User’s Manual: SW-10200 There are six QCE frame types: Ethernet Type, VLAN, UDP/TCP Port, DSCP, TOS, and Tag Priority. Frames can be classified by one of 4 different QoS classes: "Low", "Normal", "Medium", and "High" for individual application. QCL is an acronym for QoS Control List. It is the list table of QCEs, containing QoS control entries that classify to a specific QoS class on specific traffic objects. - Page 43 User’s Manual: SW-10200 The TCP protocol guarantees reliable and in-order delivery of data from sender to receiver and distinguishes data for multiple connections by concurrent applications (for example, Web server and e-mail server) running on the same host. The applications on networked hosts can use TCP to create connections to one another. It is known as a connection- oriented protocol, which means that a connection is established and maintained until such time as the message or messages to be exchanged by the application programs at each end have been exchanged.
- Page 44 User’s Manual: SW-10200 VLAN ID VLAN ID is a 12-bit field specifying the VLAN to which the frame belongs.
Need help?
Do you have a question about the SW-10200 and is the answer not in the manual?
Questions and answers