Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Summary of Contents for DCI LLC 10/100Base-TX to 100Base-FX PoE PSE FE Media Converter
- Page 2 10/100Base-TX to 100Base-FX PoE PSE FE Media Converter User's Manual Release 1.0...
- Page 3 The information in this document is subject to change without notice. Unless the explicit written permission of Manufactory Corporation, this document in whole or in part shall not be replicated or modified or amended or transmitted, in any from, or by any means manual, electric, electronic, electromagnetic, mechanical, optical or otherwise for any purpose.
- Page 4 DISCLAIMER. EXCEPT AS PROVIDED ABOVE, THE SOFTWARE IS PROVIDED “AS IS ” AND MANUFACTORY AND ITS LICENSORS MAKE NO WARRANTIES, EXPRESS OR IMPLIED, WITH REPSECT TO THE SOFTWARE AND DOCUMENTAITON. MANUFACTORY AND ITS LICENSORS DISCLAIM ALL OTHER WARRANTIES, INCLUSIVE OF WITHOUT LIMITATION, IMPLIED WARRANTIES OR MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT.
-
Page 5: Table Of Contents
Table of Contents 1. Overview ......................1 2. Model Description ..................1 3. Checklist ......................2 4. Installing the Converter ................2 5. WDM Single Fiber Model ................ 5 6. Link Fault Pass Through ................ 6 7. LED Description .................... 7 8. -
Page 6: Overview
1. Overview IEEE802.3u 100Mbps Fast Ethernet supports two types of media, 10/100Base- TX and 100Base-FX, for network connection. LFP (Link Fault Pass Through) feature enhances the TP-Fiber Link integrity and conformity. Either one of TP or Fiber port is in link-fail state, the LFP converter forces the other port to be at link- disabled state. -
Page 7: Checklist
3. Checklist Before you start installing the Converter, verify that the package contains the following: ⎯ The PoE PSE TP-Fiber Converter ⎯ AC Power Cord ⎯ This User's Manual Please notify your sales representative immediately if any of the aforementioned items is missing or damaged. - Page 8 Fig. 1 The View of PoE PSE Media Converter RJ-45 Jack 100FX Fiber Fiber Optic Networ Cat. 5 Cable PD Device (Refer to Fig. 6) Fig. 2 Connection among PSE Ethernet Switch, Fiber and TP Cables 100FX Fiber RX PoE PSE TP-to-100FX Network Converter PoE PD or...
- Page 9 Fig. 4 PoE PSE Media Converter Front Panel Fig. 5 PoE PSE Media Converter Rear Panel Fig. 6 Endpoint PSE RJ-45 Male Connector Note: IEEE802.3af assigns pairs on the RJ-45 connector and Cat.5 cable of Endpoint PSE. Endpoint : -48V via TP pin 1, 2, 3, 6...
-
Page 10: Wdm Single Fiber Model
5. WDM Single Fiber Model The TP-Fiber converter is specially designed with an optic Wavelength Division Multiplexing (WDM) model that can transport bi-directional full duplex signal over a single fiber simultaneously. Single Fiber Model TX, RX Wavelength TX (Transmit) 1310nm Single-Mode 20Km 1310nm 40/60Km models are option ∗... -
Page 11: Link Fault Pass Through
6. Link Fault Pass Through This media converter supports link fault pass through (LFP) in TX/FX converter application. Link status on one port is propagated to the other port to notice the remote nodes. If TP port is unplugged, this converter stops transmission on fiber port. This causes the remote fiber node link to fail. -
Page 12: Led Description
Note : ● indicates LNK/ACT LED Lit ○ indicates LNK/ACT LED Off Warning: The LFP ( Link Fault Pass Through) function works only when both two converters own this capability in pairs. Furthermore, both LFP converters should be supplied only by the same manufacturer/vender. The connection coming from LFP converters with odd models or non-LFP converters will cease the LFP function. -
Page 13: Connecting To Tp, Fiber Device
8. Connecting to TP, Fiber Device Converter AUTO, FORCE selectable: Bit 1, 2, 3 of S1 TP Port a. AUTO: 10/100 NWay Auto-negotiation 10/100TP b. FORCE: 100 or 10, FDX or HDX Converter 100Mbps duplex selectable: Bit 5 of S1 Fiber Port a. -
Page 14: Cable Connection Parameter
Cable Connection Parameter 100Base-X network allows 512-bit time delay between any two node-stations in a collision domain. Switch-based Media Converter breaks up TP and Fiber segments’ collision domain to extend the cabling distance. • TP Cable Limitations: Cat. 5 and up to 100m •... - Page 15 • Power Consumption : 24W • Ambient Temperature : 0° to 50°C • Humidity : 5% to 90% • Dimensions : 40(H) × 158(W) × 133(D) mm • Complies with FCC Part 15 Class A and CE Mark Note: For connecting this device to Router, Bridge or Switch, please refer to the corresponding device's Technical Manual.
Need help?
Do you have a question about the 10/100Base-TX to 100Base-FX PoE PSE FE Media Converter and is the answer not in the manual?
Questions and answers