Colored Error Code ....................28 Maintaining and Cleaning the e .......... 28 6.1 Safety regulations ................... 28 6.2 Maintenance Intervals (rule-of-thumb) ............29 Technical Specifications ..................30 Index ........................31 German Light Products GmbH (Instruction version 1.97) / from software version 1.61...
13. DMX- Input (3 Pin) 14. DMX- Input (5 Pin) Note: Only connect one cable to the 11 12 13 14 DMX Input / Output at the same time! German Light Products GmbH (Instruction version 1.97) / from software version 1.61...
9. Repair, maintenance and installation work should only be performed by qualified or GLP certified staff. You need to pay attention to the common German Light Products GmbH (Instruction version 1.97) / from software version 1.61...
Using any required kits, along with the standard mounting connectors on the base of the fixture, will ensure a safe and firm installation. German Light Products GmbH (Instruction version 1.97) / from software version 1.61...
1.1.1 Mounting in hanging position (Head down) To operate the e in a hanging position, two omega brackets can be mounted directly to the bottom of the base using the four Camlock connectors. German Light Products GmbH (Instruction version 1.97) / from software version 1.61...
Ensure that the safety wire is securely fastened through the fixture and the fixtures mounting support. Install a safety wire that can hold at least 10 times the weight of the fixture. German Light Products GmbH (Instruction version 1.97) / from software version 1.61...
Select ON/ OFF function settings with the Touchwheel. Confirm and save with the Enter-key. Push the Back-key to cancel the entry and go back to the main menu. German Light Products GmbH (Instruction version 1.97) / from software version 1.61...
Page 10
Movement Movement Manual control Speed Manual control Zoom Manual control Focus Manual control Gobo1 Manual control Gobo 1 rot. Manual control Gobo 2 Manual control Gobo 2 rot. German Light Products GmbH (Instruction version 1.97) / from software version 1.61...
Page 11
Current value for green Blue Current value for blue Error Status Shows the error status Timer Shows the life time Shows the current DMX signal per DMX channel DMX Input German Light Products GmbH (Instruction version 1.97) / from software version 1.61...
Page 12
Adjust for effect wheel rotation Prisma Adjust for prism Prisma End Pos. Adjust for prism end position Prisma Index Adjust for prism index Iris Adjust for iris German Light Products GmbH (Instruction version 1.97) / from software version 1.61...
30..4F 19..31 Shutter ramp down slow – fast 80..111 50..6F 32..43 Shutter ramp up/down slow – fast 112..143 70..8F 44..56 Random strobe slow – fast 144..159 90..9F 57..62 German Light Products GmbH (Instruction version 1.97) / from software version 1.61...
Page 14
PAN / TILT (inverse) size / phase see also 96..127 60..7F 38..50 Circle size / phase see also 128..159 80..9F 51..62 Circle (inverse) size / phase see also 160..191 A0..BF 63..75 German Light Products GmbH (Instruction version 1.97) / from software version 1.61...
Page 15
Gobo position 0 ... 540° 0..127 00..7F 0..49 Posi./Rot Gobo rotation STOP 128..129 80..81 Gobo rotation, slow-fast, 130..192 82..C0 51..75 Gobo rotation, fast-slow, 193..253 C1..FD 76..99 Gobo rotation STOP 254..255 FD..FF 99..100 German Light Products GmbH (Instruction version 1.97) / from software version 1.61...
Page 16
0..255 00..FF 0..100 9) Shutter Shutter closed 0..15 00..0F 0..5,5 Shutter pulse random slow – fast 16..47 10..2F 6..18,5 Shutter ramp up slow – fast 48..79 30..4F 19..31 German Light Products GmbH (Instruction version 1.97) / from software version 1.61...
Page 17
Gobo position 0 ... 540° 0..127 00..7F 0..49 Posi./Rot Gobo rotation STOP 128..129 80..81 Gobo rotation, slow-fast, 130..192 82..C0 51..75 Gobo rotation, fast-slow, 193..253 C1..FD 76..99 Gobo rotation STOP 254..255 FD..FF 99..100 German Light Products GmbH (Instruction version 1.97) / from software version 1.61...
Page 18
0..255 00..FF 0..100 8) Green- coarse Color mixing system – Green 0 - 100% 0..255 00..FF 0..100 9) Green- fine Color mixing system – 0..255 00..FF 0..100 Green-low German Light Products GmbH (Instruction version 1.97) / from software version 1.61...
Page 20
The Display will auto look automatically if the Touch Panel will not use for 10s. To unlook the Touch Panel you have to press one of the menu buttons for 2s.. German Light Products GmbH (Instruction version 1.97) / from software version 1.61...
Page 21
(For Germany for example: BGI 810-4 (Anhang 2) "Sicherheit bei Produktionen und Veranstaltungen - Scheinwerfer"). Color Temperature At anytime the e can be used the color correction for every RGB color. German Light Products GmbH (Instruction version 1.97) / from software version 1.61...
Remember that the reflective side of the gobo should also be towards the LED light source, so please instruct the gobo manufacturer accordingly when having customized gobos made. German Light Products GmbH (Instruction version 1.97) / from software version 1.61...
5) Push the gobo holder in the dedicated hub. Attention: There must be no gap between the gobo holder and the wheel afterwards. Check for a tight fit. German Light Products GmbH (Instruction version 1.97) / from software version 1.61...
Page 24
Gobowheel 1 (Rotation Gobos Ø 27 mm ) Position 4 Circles Vertical Bars Two Light Tunnels Triangles Random Dash Mini Dots Medium Starry Night Dense German Light Products GmbH (Instruction version 1.97) / from software version 1.61...
Page 25
Gobowheel 2 (Rotation Gobos Ø 27 mm) Position Cone Leaves Foliage Teeth Shreds Angry Hurricane Shredded Earth Diamond Pattern German Light Products GmbH (Instruction version 1.97) / from software version 1.61...
6) Attention: Don't pull the effect wheel out by grapping it with the hands at the border! 7) Change Effect wheel as desired and close the module in reverse order again. German Light Products GmbH (Instruction version 1.97) / from software version 1.61...
Page 27
Effect wheel insertion and spares: STANDARD SPARE SPARE SPARE SPARE German Light Products GmbH (Instruction version 1.97) / from software version 1.61...
4 Colored Error Code These state match to the following errors of the Impression Spot one: Color Meaning Comment critical state PCB could not find abnormal PCB send error back (hall sensor not found, encoder error, Yellow state …) Green normal state...
• Never let optical parts come into contact with oil or fat. • Before running the fixture wait until all parts are touch dry. • Never touch lenses with bare fingers. German Light Products GmbH (Instruction version 1.97) / from software version 1.61...
Length of the base 230mm / 9 inch. Height (head vertical) 618mm / 24.3 inch. Fixture weight 23 kg / 50.7 lbs. Floor stand weight 2 kg / 4.4 lbs. German Light Products GmbH (Instruction version 1.97) / from software version 1.61...