Summary of Contents for Spatz FULLHD-WIFI
- Page 1 Operation Manual FULLHD-WIFI 07/11 2011 SPATZ May change with ongoing feature upgrades and firmware improvements www.spatz-tech.com...
-
Page 2: Table Of Contents
OOT UP THE 5: WIDE ..................20 MODE CONNECTION 6: M DEVICE ............... 20 OUNTING THE TO THE 4. TROUBLESHOOTING ......................22 5. SUPPORTED RESOLUTION ....................24 6. AUDIO BIT RATE SUPPORT ....................25 7. PRODUCT SPECIFICATION ....................26 www.spatz-tech.com... -
Page 3: Important Information
any AV device connection or TV This is indoor solution. Our company has the right to modify this connection. Power outlet: To prevent electric shock, document without any notice. www.spatz-tech.com... - Page 4 802.11n router, configure it to the 2.4 Part 1: Common technical requirements GHz band rather than the 5GHz band. Optimal range between the transmitter and the receiver is between 2 and 20 meters within line of sight. www.spatz-tech.com...
- Page 5 Host system must be labeled with “Contains FCC ID: XXX-XXXXX”, FCC ID displayed on label www.spatz-tech.com...
- Page 6 This device has no Ad-hoc capability for 5250~5350MHz and 5470~5725MHz. Outdoor operations in the 5470~5725MHz band are prohibited. This device could not be used in the 5600~5650MHz. The device does not operate in 5600~5650MHz. www.spatz-tech.com...
-
Page 7: Introduction
(66 feet) LOS (Line of sight) with no latency. Both IR Sensor Extender Cable and IR Blaster Extender Cable are included in the package so users can point their remote control of the AV source at the receiver directly for device operation. www.spatz-tech.com... -
Page 8: Overview
If you have more than one pair of the devices, transmitter is paired successfully with receiver each transmitter and receiver should be at least connected to the 2nd HDTV set. 6.5 feet away from one another.. B. Full HD Receiver www.spatz-tech.com... - Page 9 If you have more than one pair of the device, each transmitter and receiver should be at If both the transmitter and the receiver exist in least 6.5 feet away from one another. the same room, the suggested the distance between the two is 6.5 feet minimum. www.spatz-tech.com...
- Page 10 LED lit in purple) and Loop-through display and the 2 display will be off. The “Standby” mode consumes 90% less of the power. User has to press power key on top cover of both transmitter and receiver to resume to “Active mode”. www.spatz-tech.com...
- Page 11 Press “SOURCE” button once for current IR blaster frequency displayed on the OSD: ▃▆█ HDMI1 CH1 WIDE Off 1280x1024 IR Blaster Frequency [47KHz] Press “SOURCE” button again within 5 seconds to change IR blaster frequency. ▃▆█ HDMI CH1 WIDE Off 1280x1024 IR Blaster Frequency [56KHz] www.spatz-tech.com...
- Page 12 ▃▆█ HDMI1 CH1 [WIDE On] 1280x1024 Press again to switch WIDE mode NOTE: Only the status of the receiver connected to the HDTV can be displayed on the OSD. The status of the transmitter HDMI out cannot be displayed. www.spatz-tech.com...
-
Page 13: Installation
(3) Connect the supplied power adapter to the Blu-ray player. DC IN jack of the transmitter and a wall socket. The LED indicator in the POWER button lights up in solid purple when the transmitter is connected to the power mains. www.spatz-tech.com... -
Page 14: Step 2: Setup The Receiver With The 2Nd Hdtv
LED indicator in the POWER button lights up in solid blue (2) Press the SOURCE / INPUT when the receiver is connected button of your TV’s remote to to the power mains. select the appropriate “HDMI” video input. www.spatz-tech.com... -
Page 15: Step 3: Setup The Ir Blaster Extender Cable And Ir Sensor Extender Cable
When the IR blaster cable is connected, signal protocol. it relays infrared command from your remote control at the device. Users can control their AV devices by pointing their remote control at the TV instead of at their AV equipment. www.spatz-tech.com... -
Page 16: Step 4: Boot Up The Transmitter And The Receiver
(3) If it is in Standby mode and the loop-through connection is on, and the both displays are off (Both POWER LED of transmitter and receiver are lit in red), press the POWER button on both transmitter and receiver to turn on the transmitter and the receiver. www.spatz-tech.com... - Page 17 (5) During the warm-up, the POWER LED will blink in blue until the signal link between the transmitter and the receiver is established. Ensure your2 TV set or projector is on “HDMI input” mode, and is already powered on. www.spatz-tech.com...
- Page 18 WIDE mode Off US (DFS) Europe (DFS) Japan (DFS) Frequency Support Channel Support Channel Support Channel [MHz] Region Region Region 5190 5230 5270 5310 5510 5550 5590 5630 5670 5755 5795 WIDE mode ON US (Non-DFS) Europe (Non-DFS) Japan (Non-DFS) www.spatz-tech.com...
- Page 19 LED description: Note: Make sure your high-definition audio/video devices connected to the transmitter has already been powered on. Warming-up or source switching time should take approximately 20~30 seconds if the operation is in normal condition. www.spatz-tech.com...
- Page 20 HDMI out; also re-plug the HDMI cable to make sure the HDMI connector had settled well. If there is no video displayed and OSD displayed “Not Supported Format”, this is an indication that the video frame rate from the source device is not supported, please refer chapter 5 to switch a supported video timing. www.spatz-tech.com...
-
Page 21: Step 5: Wide Mode Connection
2. Enable the “Wide” mode for longer distance transmission with better video quality; it’s suitable for multi-room audio/video transmission or transmission between different floors. The transmission distance when WIDE mode on is up to 100 feet (Line of Sight). www.spatz-tech.com... -
Page 22: Step 6: Mounting The Device To The Wall
(3) Insert the supplied two Anchors into the wall. (5) Place the device main holes over the protruding screws and slide down into position. (4) Insert two screws into the anchors. Leave 1/8” length for mounting the Transmitter or receiver. www.spatz-tech.com... -
Page 23: Troubleshooting
Ensure the transmission distance is less than 66 feet (LOS). Check your TV’s volume is properly set and not in "MUTE" mode. Check if the audio connectors are properly connected. No audio. Ensure the bit rate of audio from the source device can be supported www.spatz-tech.com... - Page 24 IR Blaster frequency 47K to 58K to 38K recurring.- The OSD shows: (Display 5secs) IR Blaster can’t control Source device. ▃▆█ HDMI1 CH1 WIDE Off 1280x1024 IR Blaster Frequency [47KHz] Press Source key on the top of Receiver again to switch IR Blaster frequency. www.spatz-tech.com...
-
Page 25: Supported Resolution
1920x1080p @ 29.97 / 30Hz VESA Timing (DVI only) 640x480 @ 59.94 / 72.809Hz 800x600 @ 60.317 / 72.188Hz SVGA 1024x768 @ 60 / 70.069Hz 1280x768 @ 60 Hz WXGA 1280x1024 @ 60 Hz SXGA 1600x1200 @ 60Hz UXGA www.spatz-tech.com... -
Page 26: Audio Bit Rate Support
Digital Audio from HDMI inputs: Up to 6Mbit/s bit-rate support. Support AC3 and DTS. 2-channel PCM: 16~24 bits audio sample with 32~96KHz sampling rate as below: 2channel PCM 32KHz 44.1KHz 48KHz 96KHz 16 bits 24 bits www.spatz-tech.com... -
Page 27: Product Specification
1 x LED (Two Tone: Blue / Power LED Red/purple) Red) LEDs Status LED 1x Blue LED 1 x Blue LED Signal Quality Status OSD Displayed Dimensions 181(W) x 145(L) x 33(H) mm 181(W) x 145(L) x 33(H) mm www.spatz-tech.com...
Need help?
Do you have a question about the FULLHD-WIFI and is the answer not in the manual?
Questions and answers