Selco SBT-30F User Manual

DIGITAL ACTIVE INFRARED SENSOR
INSTRUCTION MANUAL
2

SUGGESTIONS FOR INSTALLATION 1

Ensure the sensors line of sight is Ensure the sensors are
free from any false alarm sources mounted on a stable and
such as bushes, trees, etc. ( Pay firm fixing.
attention to these as they may
change seasonally.)
3

SUGGESTIONS FOR INSTALLATION 2

Note that here the protection
distances refers to the sheet
below.
Protection Spread of
Model
Distance Beam
SBT-30F
30m 0.9m
SBT-40F 1.2m
40m
1.8m
SBT-60F 60m
80m 2.4m
SBT-80F
SBT-100F 100m 3.0m
SBT-150F 150m 4.5m
4

INSTALLATION

1. Loosen screw holding cover and
remove the cover.
4. Pull wire through, install SBM
onto flange and the wall.
6. Make the optimum optical adjustment as per
section 5 and confirm system operation before
replacing covers.
Wiring distance
Model SBT-30F SBT-40F
Voltage
Wire 12V 24V 12V
diameter
2
¦Õ
0.3mm ( 0.6) 238m 2143m 238m
2
¦Õ
0.5mm ( 0.8) 417m 3750m 417m
2 ¦Õ
0.75mm ( 1.0) 556m 5000m 556m
2
¦Õ
1.25mm ( 1.2) 833m 7500m 833m
SBT-30F
SBT-40F
SBT-60F
SBT-80F
SBT-100F
SBT-150F
Ensure strong sunlight or car
headlights do not shine directly
on to the receiver. (Within
from the optical axis is not
recommended.)
Height of installation and
protection distance
33mm
14mm
0.7
33mm
~
1.0m
Protection Distance
WALL MOUNT
2. Attach the mounting pattern paper
to the wall, mark the installation
holes, and make guide holes.
5. Connect wires to the terminal.
( Refer to the Terminal Configuration
right hand side )
SBT-60F SBT-80/100F SBT-150F
24V 12V 24V 12V 24V 12V
2143m 238m 2143m 238m 2143m 238m
3750m 417m 3750m 417m 3750m 417m
5000m 556m 5000m 556m 5000m 556m
7500m 833m 7500m 833m 7500m 833m
1

PARTS DESCRIPTION

COVER
GOOD ( Green )
:on when optically aligned
:off when optically not aligned
LEVEL ( Red )
:on when Alarm is activated in accordance with Alarm LED ( Red )
ALARM ( Red )
:on when Alarm is activated in accordance with LEVEL ( Red )
Monitor jack : Should be used for making the optimum optical axis adjustment
( Refer to ' how to use the monitor jack' )
2
Obscuration time adjustment : To be used for setting the obscuration time
( Refer to ' adjustment of obscuration time ' )
Direction of installation
Horizontally 180
Because angle of reflection mirror is adjustable
in 90 horizontally and
unit can be installed in various directions.
3. Break knock-out and pull wire
through.
knock-out
TERMINAL CONFIGURATION
TAMPER
POWER ALARM
1 2 3 4 5 6 7
RECEIVER
POWER FREE TAMPER
1 2 3 4 5 6 7
TRANSMITTER
24V
2143m
3750m
5000m
7500m
Wire Hole
Connection
Terminal
LED
Vertical
Adjustment
Screw
LENS
MAIN BODY
LED
GOOD LEVEL ALARM POWER
RECEIVER TRANSMITTER
POWER ( Green )
: on when the transmitter is working
Vertically 20
In case of jump phenomenon, as shown
section in the above, change the disposition
of transmitter and receiver to the following
manner shown
10 vertically, the
POLE MOUNT
1. Pull the wire through the
wire hole of the pole.
38mm
2. Attach the bracket to the pole with the pole holder.
Bracket
Pole mount back-to-back
Each bracket to be reversely attached.
Monitor Jack
(Only for Receiver)
Obscuration Time
Adjustment
(Only for Receiver)
4 Frequency Channel
Switch
Tamper
Horizontal Angle
Adjustment Dial
Viewfinder
Cover Lock
Screw
Transmitter Receiver
Receiver
Transmitter
s ection.
Receiver Transmitter Transmitter
Receiver
~ 50mm
Pole cover
Pole holder