Advertisement
Getting Started
Installing the Batteries
This unit operates on 3 AA batteries. If the sound
becomes weak or distorted or the Low Battery icon
appears on the display, it's time to replace the
batteries.
ATTENTION: Batteries should only be installed by an
adult.
³ Use a Phillips screwdriver to open the battery
compartment door located on the back of the unit.
Install 3 AA size batteries, making sure that the +
and – polarities match the diagram printed inside
the battery compartment.
Close the battery compartment door and tighten
the battery door screw. Do not over-tighten.
For the Best Possible Performance
•
We recommend the use of alkaline batteries for longer
life.
•
Do not mix old and new batteries.
•
Do not mix alkaline, standard (carbon-zinc) or
rechargeable (nickel-cadmium) batteries.
•
Batteries are to be inserted with correct polarity.
•
Remove exhausted batteries from the unit.
•
Do not attempt to recharge non-rechargeable
batteries.
•
Remove the rechargeable batteries from the unit
before charging.
•
The supply terminals are not to be short-circuited.
•
Batteries should be removed if the item will not be
used for an extended period of time, such as a month
or longer, to prevent battery leakage or damage.
•
Rechargeable batteries should only be charged under
adult supervision.
•
Only batteries of the same or equivalent type as
recommended are to be used.
Unpacking and Setup
1. Remove the product and all packing materials from
the carton.
2. It is a good idea to save the packing materials in case
the unit needs to be returned for service. If you do
dispose of the packing materials, please do so
properly.
3. Remove the demo tab from the battery compartment
on the back of the unit and the clear protective film
from the clock display.
4. Insert the tail stand in the back of the unit for proper
stability
5. The unit should be placed on a level surface, away
from direct sunlight, and away from the sources of
excess dust, dirt, heat, water, moisture, vibration, and
strong magnetic fields.
6. Protect your furniture when placing the unit on natural
wood or wood with a lacquered or coated finish. A
cloth or other protective material should be placed
between the unit and the furniture.
Resetting the Unit
If the unit becomes locked up or frozen, insert a paper
clip or similar into the Reset Port on the back of the unit
and press in. Doing so will reset the music chip.
Battery Installation (back of unit)
MP3 Timer/Off Button
Rev Button
Time Set Button
Clock Display
Alarm Set/Reset Button
Alarm ON indicator
PM indicator
Insert Tail Stand In Back Of Unit
For Proper Stability
MP3 Line-in Jack
Reset Port
SFX Button
Snooze Button
Alarm On/Off Switch
Fwd Button
Time
Low Battery indicator
The Display
Setting the Time
1. Press and hold the Time Set Button until the display
flashes.
2. Press the FWD or REV Button to adjust the clock to
the current time (hold for rapid adjustment). Remember
to set the correct AM or PM time. A PM indicator appears
at the bottom left of the display; there is no AM indicator.
3. Press the Time Set Button (or no button within 10
seconds) to confirm time and exit time setting mode.
Setting and Using the Alarm
The alarm on this unit features sound effects, flashing lights
and speech. It has a gradual alarm which starts off quiet and
gets louder.
To view the current set alarm time, press the Alarm
Set/Reset Button. You can toggle the alarm ON or OFF by
sliding the Alarm On/Off Switch. An alarm icon will appear
in the upper left of the display, indicating the alarm is armed.
1. Press and hold the Alarm Set/Reset Button until the
display flashes.
2. Press the FWD or REV Button to adjust the clock to
the desired alarm time (hold for rapid adjustment).
Remember to set the correct AM or PM alarm time. A
PM indicator appears in the display; there is no AM
indicator.
3. Press the Alarm Set/Reset Button (or no button within
10 seconds) to confirm alarm setting time and exit alarm
setting mode.
4. When the alarm is sounding, press the Alarm Set/Reset
Button to stop the alarm sounding and reset it to come
on the next day at the same time.
5. Press the Snooze Button to temporarily silence the
alarm for about 9 minutes. After this, the alarm will sound
again. You can press the Snooze Button several times
during the duration of the alarm (about an hour).
Using the MP3 Line-in
1. Connect one end of a standard 3.5mm stereo audio
cable (not included) to the headphone or line-out jack
of your audio device and plug the other end into the
MP3 Line-in Jack on the back of the unit.
2. Press the MP3 Timer Button (press down on Perry's
right hand) as needed to cycle through the MP3 Timer
Settings: 60, 45, 30, 15 minutes or OFF.
3. Turn on your audio device and put it in PLAY mode.
Adjust the volume on the audio device as needed.
The unit will play the audio from your audio device for
the preset time, then turn off. To turn off the unit before
the set time, press the MP3 Timer Button until OFF
appears. Remember to turn off your audio device, too!
Using the Sound Effects
1. Press the SFX Button (press down on Perry's left hand)
to cycle through the various sound effects, speech and
cool lighting effects.
Advertisement
