Advertisement
This Installation Guide presents a quick, standard installation of the SP201-SA.
Note: The needs of your network may require an installation that varies from the standard installation.
For a customized installation, see the SP201-SA Customization and Maintenance Guide. For hardware
information, see the SP201-SA Hardware Reference Guide.
The SP201-SA is available in two versions:
• The two-port SP201-SA, supporting one trunk circuit of up to 30 channel circuits
• The four-port SP201-SA, supporting up to two trunk circuits of up to 30 channel circuits each (for a total
of up to 60 channel circuits)
Note: A standard trunk circuit (from one external device, through the SP201-SA, to another external
device) comprises trunk connections to two ports. The SignalPath™ configuration software defines each
side of the trunk circuit (that is, each connection to a port) as a trunk.
This document uses the term trunk to indicate a connection to one port; it uses the term trunk circuit to
indicate the complete end-to-end connection (over two ports). Using these definitions, a trunk circuit
comprises two trunks.
Before you start this installation, be sure you have filled out the worksheet for adding this device to your
network. See the SP201-SA Site Planning Worksheet.
See the following sections for a standard installation of the SP201-SA:
•
Section A, Physical Installation
•
Section B, Port Configuration
•
Section C, Clocking Configuration
•
Section D, Trunk Configuration
•
Section E, Channel Configuration
•
Section F, SP201-SA Warmstart
!
TM
Copyright 2003 Encore Networks, Inc.
SignalPath
(SP201-SA
Installation Guide
SignalPath Software Version 1100
All rights reserved.
™
201-SA
™
)
Version C, July 2004
Part Number 15469.0100
Advertisement
Table of Contents
Summary of Contents for Encore SP201-SA
-
Page 1: Installation Guide
• The two-port SP201-SA, supporting one trunk circuit of up to 30 channel circuits • The four-port SP201-SA, supporting up to two trunk circuits of up to 30 channel circuits each (for a total of up to 60 channel circuits) Note: A standard trunk circuit (from one external device, through the SP201-SA, to another external device) comprises trunk connections to two ports. -
Page 2: Channel-Associated Signaling (Cas)
1. Place the SP201-SA on a tabletop or shelf. 2. Connect the cables for one set of trunks to the ports on the rear of the SP201-SA chassis, as follows: a For the CAS trunk (DTMF, R1, R2, or N5), do one of the following: For DTMF or R1, connect a T1 cable to the RJ48C port labeled Port 1. - Page 3 (and vice versa), and channels on trunk 2 map to channels on trunk 4 (and vice versa). 3. If you are installing a four-port SP201-SA, connect another set of trunks to ports on the rear of the chassis, as follows: a For the CAS trunk (DTMF, R1, or R2), do one of the following: For DTMF or R1, connect a T1 cable to the RJ48C port labeled Port 2.
-
Page 4: Port Configuration
20) 2 E1 120 Ohm/2 E1 120 Ohm Enter LIM Choice from list above [1-20] (current=11) ==> Select the configuration that supports your SP201-SA’s port connections, and press the Enter key. (The List of Valid LIMs shown is for a four-port SP201-SA.) - Page 5 (Initializations) (Application banner and (When you see the user> user> prompt) prompt, the SP201-SA is ready for further configuration.) C Clocking Configuration What the terminal displays What you type What you are configuring...
-
Page 6: Trunk Configuration
SP201-SA™ Installation Guide D Trunk Configuration Perform the following procedure once for each trunk on the SP201-SA. What the terminal displays What you type What you are configuring config framer p where p is the port number (1, 2, 3,... - Page 7 SP201-SA™ Installation Guide E Channel Configuration See the following sections to configure the protocols in your SP201-SA: • DTMF signaling Section E.1, Channel Configuration for DTMF Signaling • R1 signaling Section E.2, Channel Configuration for R1 Signaling • R2 signaling Section E.3, Channel Configuration for R2 Signaling...
- Page 8 All R1 channels user> config r1 all Placement of channels 1–31 of trunk 1 and (on the four-port SP201-SA) channels 1–31 of Set 1/1 thru 2/31 out-of-service? trunk 2 into service (y or n) : <current=n> Template # for default IAM ? : Use of R1 IAM template 1 (range 1 - 5) : <current=1>...
- Page 9 All R2 channels user> config r2 all Placement of channels 1–31 of trunk 1 and (on the four-port SP201-SA) channels 1–31 of Set 1/1 thru 2/31 out-of-service? trunk 2 into service (y or n) : <current=n> Select R2 converter mode : <...
- Page 10 All N5 channels user> config n5 all Placement of channels 1–31 of trunk 1 and (on the four-port SP201-SA) channels 1–31 of Set 1/1 thru 2/31 out-of-service? trunk 2 into service (y or n) : <current=n> Destination country code for calls to Your country’s international...
- Page 11 Generate ringback tone for N5 SignalPath for calls from N5 originated calls? (y or n) : device <current=n> (This completes standard configuration of N5 signaling. If you wish to customize the configuration of N5 signaling, refer to the SP201-SA Customization and Maintenance Guide.) user>...
-
Page 12: Isdn Connection
In the two-port SP201-SA, perform the following procedure once for trunk 2. In the four-port SP201-SA, perform the procedure once each for trunks 3 and 4. Note: If you are performing this procedure on a two-port SP201-SA, read trunk 3 as trunk 2. What the terminal displays... - Page 13 In the two-port SP201-SA, perform the following procedure once for trunk 2. In the four-port SP201-SA, perform the procedure once each for trunks 3 and 4. Note: If you are performing this procedure on a two-port SP201-SA, read trunk 3 as trunk 2. What the terminal displays...
- Page 14 (Application banner) (When you see the user> prompt, the SP201-SA is ready for use.) user> This completes the standard installation. To configure other parameters, see the SP201-SA Customization and Maintenance Guide. For hardware specifications, see the SP201-SA Hardware Reference Guide.
Need help?
Do you have a question about the SP201-SA and is the answer not in the manual?
Questions and answers