Advertisement
Advertisement
Table of Contents
Summary of Contents for FLI Audio FT10A-F6
- Page 1 ACTIVE ENCLOSURES FT10A-F6, FT10AP-F6, FT12A-F6, FT12TA-F6...
- Page 2 OWNERS MANUAL Congratulations on purchasing your FLI bass enclosure. Please read this manual in order to fully understand how to get the best results from this product and ensure that all advice on how to look after the product is followed. Thank you for buying FLI, we hope you enjoy listening to your product as much as we enjoyed creating it.
-
Page 3: Limited Warranty
FLI. Graphics and logos are trademarks or trade dress of FLI audio or its subsidiaries. FLI’s trademarks and trade dress may not be used in connection with any product or service that is not FLI’s, in any manner that is likely to cause confusion among customers or in any manner that disparages or discredits FLI. -
Page 4: Mounting Guidelines
MOUNTING GUIDELINES Your FLI enclosure is designed with a swift installation routine in mind. Before fixing the enclosure in place please ensure that there is sufficient air flow around the exterior of the amplifier casing, at least two inches is sufficient. POWER CONNECTIONS Remote turn on Fuse close to battery... -
Page 5: Ground Cable
CONNECTIONS Length of Run Current demand 0 – 4 Ft 4 – 7 Ft 7 – 10 Ft 10 – 13 Ft 13 – 16 F 16 – 19 Ft 19 – 22 Ft 22 – 28 Ft 0–20 amps 20–35 amps 35–50 amps 50–65 amps... - Page 6 TERMINALS AND CONNECTIONS 1. Fuse FT10A / FT10AP / FT12A: ensure a 20 amp fuse is fitted, never fit a fuse with a rating higher than 20 amps. FT12TA: ensure a 25 amp fuse is fitted, never fit a fuse with a rating higher than 25 amps. 2.
-
Page 7: Installation
INSTALLATION The most common place to mount a bass enclosure is in the luggage compartment of the vehicle. Where in the luggage compartment it is mounted will have an effect on the sound produced, allowing the user to tailor the sound to suit their musical tastes. For example, if the enclosure is mounted facing the rear bumper the bass produced will be noticeably deeper than if it is fired into the rear seat. -
Page 8: Run-In Procedure
RUN IN PROCEDURE FLI recommends that you follow the run in procedure for the subwoofer detailed below. • When your subwoofer is used for the first time, naturally like most brand new items it is very stiff and rigid. It will take time for the moving parts of the subwoofer to loosen up before the subwoofer is ready to deliver it’s full potential. -
Page 9: Troubleshooting
• Check that the positive wire is connected to the +12V terminal of the amplifier • Check that the negative wire is connected to the GND terminal of the amplifier • Check that the correct fuse is fitted. FT10A-F6 / FT10AP-F6 / FT12A-F6: 1 x 20 amp FT12TA-F6: 1 x 25A DISTORTED SOUND... - Page 10 UK TECHNICAL ENQUIRIES Call 09067031420 Calls cost 50p per minute. Call costs correct at date of publication (01/02/12) Hours of business 9.00am - 5.30pm GMT Monday - Friday. All calls are recorded for training purposes. MIDBASS Distribution PO Box 11000 B75 7WG INTERNATIONAL TECHNICAL ENQUIRIES For international technical support please contact the distribution agent for your country.
-
Page 11: Specification
SPECIFICATION MODEL FT10A-F6 FT10AP-F6 FT12A-F6 FT12TA-F6 AMPLIFIER FL250M-F4 FL250M-F4 FL250M-F4 FL500M-F4 RMS POWER 300 watts 300 watts 400 watts 800 watts PEAK POWER 1000 watts 1000 watts 1200 watts 2400 watts IMPEDANCE 4Ω 4Ω 4Ω 4Ω HEIGHT 11.4” (290mm) 11.4” (290mm) 13.4”... - Page 12 WWW.FLIAUDIO.COM www.facebook.com/fliaudio...