Advertisement
Operation Guide 3227
To set an alarm time
1. In the Alarm Mode, use E and D to scroll through the
Alarm number
alarm screens until the one whose time you want to set
is displayed.
Press E.
Alarm1
Hourly Time
Signal
AM Indicator
Alarm 2 on indicator
You can configure Alarm1 as a snooze alarm or a
one-time-alarm. Alarms 2 through 5 can be used as
Hour : Minutes
one-time alarms only.
The snooze alarm repeats every five minutes.
2. After you select an alarm, hold down A until the hour
setting of the alarm time starts to flash, which indicates
the setting screen.
Month–Day
This operation automatically turns on the alarm.
E-20
Alarm Operation
The alarm tone sounds at the preset time for 10 seconds, regardless of the mode the
watch is in. In the case of the snooze alarm, the alarm tone operation is performed a
total of seven times, every five minutes, until you turn the alarm off or change it to a
one-time alarm (page E-24).
Pressing any button stops the alarm tone operation.
Performing any one of the following operations during a 5-minute interval between
snooze alarms cancels the current snooze alarm operation.
Displaying the Timekeeping Mode setting screen (page E-6)
Displaying the alarm 1 setting screen (page E-20)
To test the alarm
In the Alarm Mode, hold down C to sound the alarm.
Pressing C also toggles the currently display alarm or the Hourly Time Signal on
and off.
E-22
To select the operation of Alarm 1
1. In the Alarm Mode, use E and D to select Alarm1.
2. Press C to cycle through the available settings in the sequence shown below.
SNZ indicator and Alarm1 on indicator
C
One-time alarm on
Snooze alarm on
C
The SNZ indicator and Alarm1 on indicator (AL-1) are displayed in all modes.
The SNZ indicator flashes during the 5-minute intervals between alarms.
The alarm indicator (AL-1 and/or SNZ) flashes while the alarm is sounding.
E-24
To measure times with the stopwatch
Elapsed Time
C
C
C
➤
➤
Start
Stop
Re-start
Split Time
A
C
A
➤
➤
Start
Split
Split release
(SPL displayed)
Two Finishes
C
A
C
➤
➤
Start
Split
Stop
First runner
Second runner
finishes.
finishes.
Display time of
first runner.
E-26
To use the countdown timer
Press C while in the Countdown Timer Mode to start the countdown timer.
When the end of the countdown is reached, the alarm sounds for 10 seconds or until
you press any button to stop it. The countdown time is automatically reset to its
starting value after the alarm stops.
The countdown timer operation continues even if you exit the Countdown Timer
Mode.
Press C while a countdown operation is in progress to pause it. Press C again to
resume the countdown.
To stop a countdown operation completely, first pause it (by pressing C), and then
press A. This returns the countdown time to its starting value.
E-28
Press D.
Alarm 2
Alarm 3
Alarm 5
Alarm 4
C
Alarm off
C
A
➤
➤
Stop
Clear
C
A
➤
➤
Stop
Clear
A
A
➤
➤
Split release
Clear
Display time of
second runner.
3. Use C and B to move the flashing in the sequence shown below to select other
settings.
Press C.
Hour
Minutes
Press B.
4. While a setting is flashing, use E (+) and D (–) to change it.
To set an alarm that does not include a month (Daily alarm, Monthly alarm), set x
for the month. Use E and D until the x mark appears (between
month setting is flashing.
To set an alarm that does not include a day (Daily alarm, 1-Month alarm), set xx
for the day. Use E and D until the xx mark appears (between the end of the
month and ) while the day setting is flashing.
When setting the alarm time using the 12-hour format, take care to set the time
correctly as a.m. (A indicator) or p.m. (P indicator).
5. Press A to exit the setting screen.
To turn Alarms 2 through 5 and the Hourly Time Signal on and off
1. In the Alarm Mode, use E and D to select a one-time
Alarm on indicators
alarm (alarm 2 through 5) or the Hourly Time Signal.
2. Press C to toggle it on and off.
The current on/off status of Alarms 2 through 5 is
shown by indicators (AL-2 through AL-5). The SIG
indicator shows the on (SIG displayed)/off (SIG not
displayed) status of the Hourly Time Signal.
The alarm on indicators and Hourly Time Signal on
indicator are displayed in all modes.
While an alarm is sounding, the applicable alarm on
Hourly Time Signal
indicator flashes on the display.
on indicator
Stopwatch
Minutes
The stopwatch lets you measure elapsed time, split times,
Hours
Seconds
and two finishes.
The display range of the stopwatch is 23 hours, 59
minutes, 59.99 seconds.
The stopwatch continues to run, restarting from zero
after it reaches its limit, until you stop it.
The elapsed time measurement operation continues
even if you exit the Stopwatch Mode.
Exiting the Stopwatch Mode while a split time is frozen
on the display clears the split time and returns to
Timekeeping
elapsed time measurement.
Mode time
All of the operations in this section are performed in the
1/100 second
Stopwatch Mode, which you enter by pressing B (page
E-5).
Countdown Timer
Minutes
The countdown timer can be set within a range of 1
Hours
Seconds
minute to 24 hours. An alarm sounds when the countdown
reaches zero.
All of the operations in this section are performed in the
Countdown Timer Mode, which you enter by pressing
B (page E-5).
To set the countdown start time
1. In the Countdown Timer Mode, hold down A until the
hour setting of the countdown start time starts to flash,
Timekeeping Mode time
which indicates the setting screen.
2. Press B or C to move the flashing between the hour
and minute settings.
3. While a setting is flashing, use E (+) and D (–) to change it.
To set the starting value of the countdown time to 24 hours, set 0:00.
4. Press A to exit the setting screen.
Dual Time
The Dual Time Mode lets you keep track of time in a
Dual time
different time zone. You can select Standard Time or
(Hour : Minutes Seconds)
Daylight Saving Time for the Dual Time Mode time, and a
simple operation lets you view the Timekeeping Mode
screen or Data Bank Mode screen.
The seconds count of the Dual Time is synchronized
with the seconds count of the Timekeeping Mode.
All of the operations in this section are performed in the
Dual Time Mode, which you enter by pressing B (page
E-5).
Timekeeping Mode time
To set the Dual Time
1. In the Dual Time Mode, hold down A until the hour setting start to flash, which
indicates the setting screen.
2. Press B or C to move the flashing between the hour and minute settings.
3. While a setting is flashing, use E (+) and D (–) to change it.
4. Press A to exit the setting screen.
Month
Day
and ) while
E-21
E-23
E-25
E-27
E-29
Advertisement
