Peco DCC-1 User Manual

USING the DCC 1

Compass Function (C o )
Press the button
one (1) time. The
display reads C o to
identify the current
Adjust instrument
function, and the
CLOCKWISE to obtain
compass aim (0 -
level.
359°) is shown in
Instrument in Current bearing Exit the Compass (C o ) function by pressing the button
the display. Use the
Compass mode (C o )
displayed
sighting line (– + –) once, or jump directly to the Angle mode by pressing and
in the display to guide your aim, trying to maintain a holding the button for 2 seconds until the Angle function
horizontal position while sighting. (Ang) is displayed.
The DCC-1 will

Angle Measuring Function (Ang)

compensate the
compass angle
if tilted in any
direction up to
±10°, however,
the steadier the
Tilt indicator directs to Tilt indicator directs
instrument is held,
point instrument UP to to point instrument
the better the
obtain level. DOWN to obtain level.
function.
8
7168_Instructions-c.indd 1
DCC-1 Technical Specifi cations
When adjusting
CLOCKWISE
• Vertical Angles
or COUNTER
• Resolution
CLOCKWISE,
• Accuracy
gently rotate the
• Horizontal Angles
instrument along
• Resolution
an imaginary axis
Adjust instrument
through the sight. • Accuracy
COUNTERCLOCKWISE
• Battery
to obtain level.

Warranty and Service Information

Peco Sales, Inc. warrants that this product shall be free
from defects in materials and workmanship, under normal
intended use, for a period of one (1) year from the date of
purchase. The warranty excludes batteries, accessories
and any written or downloadable materials. The warranty
does not apply if the product has been improperly
Press the button two (2) times. The
installed, activated, calibrated or operated in a manner
display reads Ang to identify the Angle
not in accordance with the User Guide. Warranty is also
function, and the current vertical
automatically expired if the product has been exposed to
Angle (-90.0° to 90.0°) is shown in
external force and warranty is not applicable for cosmetic
the display.
defects.
The limited warranty time covers obvious fabrication defects.
Use the sighting line (– + –) in the Defects in the electronic components that are impossible for
the manufacturer to detect prior to assembling and shipping
display to guide your aim to the
DEG DEG DEG
of the product may occur. Peco Sales, Inc. assumes no
desired target. Exit the Angle function
liability for problems of this nature and claims no liability
by pressing the button once.
for any loss of business, profi ts, savings, consequential
damages or other damages resulting from use of the
products described. Signs of misuse, negligence, cosmetic
9
damage or accidents automatically withdraw the warranty.
Warranty is valid in the country of purchase. A product
-90.0° to 90.0°
covered by warranty will be subject to exchange, service and
0.1°
repair or according to special agreement between seller and
0.2°
buyer, within the frames of the limited warranty. Peco Sales,
0 to 359° (0° = North) Inc. reserves the right to determine which option will be most
suitable for each separate case after having examined and
1°
evaluated the product.
2.5°
One 1.5V AA
Proof of Warranty
For a valid warranty, a copy of invoice or dated receipt of
your purchase must be presented. The serial number of the
returned product must be clearly stated upon return. Call
800-752-8460 or visit http://www.pecosales.com/home/
terms.asp for return information.
Return freight charges are the responsibility of the customer,
except on instruments covered under warranty. If warranty
has expired or is deemed null and void, all freight charges are
the responsibility of the customer.
Peco Sales, Inc. will perform repair and service of products
where warranty has expired when possible. Cost estimates
will be provided upon examination and evaluation of the
returned product for cost approval.
© Copyright 2009 Forestry Suppliers, Inc. All rights reserved.
No part of this document may be reproduced without the express
permission of the publisher.
10 11
Post Offi ce Box 8122
Jackson, MS 39284-8122
DCC-1
T: 800-346-6939
F: 877-882-2466
Digital Compass/Clinometer
Peco Sales is a wholly owned subsidiary wholesale division
of Forestry Suppliers, Inc., Jackson, Mississippi, USA
North American User Guide
Printed in Sweden
8/12/09 9:56 AM