Subscribe to Our Youtube Channel
Summary of Contents for Pakedge Device & Software RSB-KIT
- Page 1 RSB-KIT Preconfigured Audio/Video Bridging System Installation Manual – Version 2.0...
- Page 2 MUST BE INSTALLED AND USED IN STRICT ACCORDANCE WITH THE MANUFACTURER’S INSTRUCTIONS AS DESCRIBED IN THE USER DOCUMENTATION THAT COMES WITH THE PRODUCT. WARNING: POSTPONE INSTALLATION UNTIL THERE IS NO RISK OF THUNDERSTORM OR LIGHTNING ACTIVITY IN THE AREA. RSB-KIT INSTALLATION MANUAL...
- Page 3 • Keep the device away from excessive heat and humidity and keep the device free from vibration and dust. • Do not directly cover the device, or block the airflow to the device with insulation or any other objects. RSB-KIT INSTALLATION MANUAL...
- Page 4 **** 1) No Factory Reset - The RSB-KIT was designed to be a very robust and exceptionally reliable product. Because of this, you will find the RT-50V does not have a hardware or software reset button. The product can only be reset by Pakedge either remotely, if the router is connected to a working internet connection with remote access or at Pakedge’s facility.
-
Page 5: Table Of Contents
5 SUBSCRIPTION SERVICES .........................36 6 CHANGING DEFAULT PASSWORDS ....................38 APPENDIX A – TROUBLESHOOTING FAQ’S ..................40 APPENDIX B – SPECIFICATIONS ......................42 APPENDIX C – TECHNICAL SUPPORT ....................45 APPENDIX D – LIMITED WARRANTY ..................... 46 RSB-KIT INSTALLATION MANUAL... -
Page 6: Introduction
The very Basic (Section 2.2.2) setup would be- configure the router for the type of internet service such as Dynamic, Static and PPPoE and plug the appropriate cables into the different VLAN/Priorities depending on device. RSB-KIT INSTALLATION MANUAL... -
Page 7: Package Content
• Gray CAT5E Cable (Switch port 1 to Router Ports 1, 2 or 3) • Red CAT5E Cable (WAN 1 Port to Internet Connection) • Installation Manual - (Basic Only, Advanced Features Manual is Downloadable on www.pakedge.com/userguides.php ) • Hardware Accessories RSB-KIT INSTALLATION MANUAL... -
Page 8: Getting To Know The Rt-50V
Normal Operation. The correct cable is in use and the Green connected equipment has power. Link / Activity Flashing Green Network activity at this interface. No link established. 10/100 Green The interface is connected at 100 Mbps. RSB-KIT INSTALLATION MANUAL... -
Page 9: Description For Ports
RJ-45 Redundant connections to the Internet. WAN 2 Optional connection to the CONSOLE RJ-45 9600 bps RS-232-C management computet. Provides access to the command line interface (CLI). Optional connection for FortiUSB key for firmware backup and installation. RSB-KIT INSTALLATION MANUAL... - Page 10 To power the switch, plug the female end of the power cord firmly into the receptacle of the switch and the other end into a power outlet. After the power cord is plugged in, the power LED should be a solid green to indicate normal power status. RSB-KIT INSTALLATION MANUAL...
-
Page 11: Getting To Know The Sw8-Gbv
LEDs for each port: The switch provides one “1000M” LED and one “10/100M” LED for each port. 1000M LED: Shows the current transmitting/receiving speed of the port. 10/100M LED: Shows link status and the activities on the port. RSB-KIT INSTALLATION MANUAL... -
Page 12: Description For Ports
Note: The mini GBIC slot shares the same LED indicator with port 8. LED for the device: The SW8-GBP’s power (PWR) LED reads as follows: STATUS OPERATION Power Steady Green The switch is powered on. The switch is turned off. RSB-KIT INSTALLATION MANUAL... - Page 13 The auto-negotiation feature allows the ports to run at one of the following operation modes: STATUS OPERATION 10/100/1000Mbps (copper) Full Duplex 10Mbps Half Duplex Full Duplex 100Mbps Half Duplex 1000Mbps Full Duplex 1000Mbps (Fiber) 1000Mbps Full Duplex (mini GBIC required) RSB-KIT INSTALLATION MANUAL...
- Page 14 To power the switch, plug the female end of the power cord firmly into the receptacle of the switch and the other end into a power outlet. After the power cord is plugged in, the power LED should be a solid green to indicate normal power status. RSB-KIT INSTALLATION MANUAL...
-
Page 15: Network Configuration/Setup Overview
2 Network Configuration/Setup Overview 2.1 Summary of Settings & IP Address Configuration Pakedge Factory Default Settings for RSB-KIT Network Internal Interface (VLAN1) 192.168.1.99 VLAN2 192.168.2.1 VLAN3 192.168.3.1 VLAN4 192.168.4.1 VLAN5 192.168.5.1 WAN1 Interface Dynamic IP Service WAN2 Interface Dynamic IP Service... -
Page 16: Planning Your Network
NOT mean a device in one VLAN will not be able to communicate with a device on another VLAN.. In summary, all devices can see each other when addressing their IP address, even if they are on a different VLAN. However, broadcasts are limited to the VLAN the device is on. RSB-KIT INSTALLATION MANUAL... - Page 17 Preconfigured VLAN Networking Equipment Suggested Network Configuration RSB-KIT INSTALLATION MANUAL...
- Page 18 802.1Q Trunk ports of the Router) to expand the number of available ports. A gray CAT5E cable is provided with every SW8-GBV switch to connect to one of the 3 802.1Q trunk ports on the RT-50V Router. RSB-KIT INSTALLATION MANUAL...
-
Page 19: Basic Setup
1. Section 3 to complete the hardware installation 2. Then Section 4 to configure the broadband internet connection. 3. At this point, you are up and running, however if you desire to activate the optional Security Subscription, go to Section 5. RSB-KIT INSTALLATION MANUAL... -
Page 20: Advanced Features Setup
It permits a user to establish safe and secure remote access sessions from virtually any internet browsers to access home controls, share files, etc. SSL VPN advantage over IPsec VPN is that a client software does not need to be installed. RSB-KIT INSTALLATION MANUAL... - Page 21 Finally, additional features can be added by referring to the Fortinet Administrator Guide for the Fortigate-50B http://www.pakedge.com/docs/fortigate_admin_4.pdf. Please note, Pakedge does not support anything outside of these features. If support is required, it can be purchased from Fortinet. Please contact Pakedge for details. RSB-KIT INSTALLATION MANUAL...
-
Page 22: Hardware Installation
3 Hardware Installation 3.1 Installing the Router and Switch 3.1.1 Securing RV-50V in RMB-FG Rack Mount Bracket Remove Rubber feet from RT-50V Guide RT-50V Router into Rackmount Bracket RMB-FG RSB-KIT INSTALLATION MANUAL... - Page 23 Flip over and align screw holes with those of router. Use the supplied 4 x M3 screws to attach the RT-50V to the RMB-FG as shown Plug in AC/DC Power supply into Router RSB-KIT INSTALLATION MANUAL...
-
Page 24: Connecting Cables To Switch Router
Grab the other end of gray cable and Plug into Port 1 of RT-50V Note - If you are using multiple SW8-GBV switches, then connect the remaining switches to Ports 2 or 3 on the RT-50V using the Gray CAT5E cables RSB-KIT INSTALLATION MANUAL... - Page 25 Find one of your region power cords supplied with SW8-GBV and Plug power cord into SW8-GBV switch Find the other of your region power cords supplied with RT-50V and plug power cord into RT-50V router RSB-KIT INSTALLATION MANUAL...
-
Page 26: Broadband Software Configuration
Power down the internet provider supplied device and leave it powered down for one minute. Plug the Ethernet cable from the ISP device into the “WAN1” port on the RT-50V Router. Power up the internet provider supplied device, wait one minute then power on the Router. RSB-KIT INSTALLATION MANUAL... -
Page 27: Static Ip
2) Plug an Ethernet cable from the SW8-GBV and to a PC computer. 3) Open Internet Explorer on the PC and go to http://192.168.1.99. 4) At the login prompt type in the username: user and the password: user. RSB-KIT INSTALLATION MANUAL... - Page 28 5) Click on Network under System on the left hand side of the screen. Click on Interface. 6) Double click on the wan1 row RSB-KIT INSTALLATION MANUAL...
- Page 29 7) Click on the “Manual” radio button under the “Addressing Mode” heading. Enter the IP address and Subnet mask information provided by the ISP, then click “OK”. We are using 100.100.100.100/255.255.255.0 as an example only. RSB-KIT INSTALLATION MANUAL...
- Page 30 8) You are now connected to the internet, however to ensure the optimal performance, we recommend replacing the default DNS settings with your ISP’s DNS settings. To add your ISP’s DNS information, log off “user” and login again using the adminstrator name - pakedge, and the password - pakedgef. RSB-KIT INSTALLATION MANUAL...
- Page 31 9) Now, to add the DNS, Click on System | Network and click on the Options tab. RSB-KIT INSTALLATION MANUAL...
- Page 32 10) Type in the DNS values that you received from your ISP and then click Apply. We are using 4.2.2.1 and 4.2.2.2 as an example only as seen below. RSB-KIT INSTALLATION MANUAL...
- Page 33 12) In the “Gateway” field, type in the default gateway provided by the ISP and then click “OK”. We are using 100.100.100.1 only as an example. Note - Make sure that the “Device” is set to “wan1”. 13) The Router is now configured and ready to be used. You can close the browser window. RSB-KIT INSTALLATION MANUAL...
-
Page 34: Pppoe Configuration
2) Connect an Ethernet cable from the SW8-GBV and to a PC computer. 3) Open Internet Explorer on the PC and go to http://192.168.1.99. 4) At the login prompt type in the username: user and the password: user. RSB-KIT INSTALLATION MANUAL... - Page 35 5) Click on Network under System on the left hand side of the screen. Click on Interface 6) In the WAN1 row, Click on the Edit icon, it looks like a pencil and paper- see graphic below. RSB-KIT INSTALLATION MANUAL...
- Page 36 7) Click on the “PPPoE” radio button under the “Addressing Mode” heading. Enter the username and password information provided by the ISP. Click on OK. 8) The Router is now configured to use a PPPoE connection and is ready to be used. You can close the browser window. RSB-KIT INSTALLATION MANUAL...
-
Page 37: Subscription Services
Furthermore, friendly reminders will be sent to you to indicate upcoming renewals. All subscriptions come with 8x5 or 24x7 Fortinet support. Support contracts can also be purchased individually as needed. RSB-KIT INSTALLATION MANUAL... - Page 38 1 year, 2 year, 3 year, 4 year, or 5 year Antispam, Intrusion Protection Bundle 24x7 Fortinet Comprehensive Support + RT-B247 1 year, 2 year, 3 year, 4 year, or 5 year Antivirus, Antispam, Intrusion Protection Bundle RSB-KIT INSTALLATION MANUAL...
-
Page 39: Changing Default Passwords
Basic Setup and pakedge for Advanced Setup. 1) Logon using the username and password you want to change, either: i) Username - user, Password - user ii) Username - pakedge, Password - pakedgef 2) Click on System | Admin RSB-KIT INSTALLATION MANUAL... - Page 40 After that, select “change password” from the top menu. 4) Type in the old password followed by the new password twice and then hit OK 5) Repeat steps 1-4 for the second username. In this example, pakedge RSB-KIT INSTALLATION MANUAL...
-
Page 41: Appendix A - Troubleshooting Faq's
As a result, configuration is not as intuitive as the low end routers and education is needed to understand and configure fully. The Pakedge preconfigured version is designed only to support set configurations to make configuring the router straight forward and simple. Fortinet is better equipped to support configurations beyond the basic residential application. RSB-KIT INSTALLATION MANUAL... - Page 42 Appendix A – Troubleshooting FAQ’s (continued) 4- What is the RSB-KIT and what are the advantages of purchasing the product this way? - The RSB-Kit comprises of the RT-50V router/security application, the Pakedge SW8-GBV 8-Port Gigabit VLAN switch and all a rack mount hardware to install both products into a AV rack. The kit contains everything an installer needs to quickly install and configure a powerful VLAN based enterprise network into any home.
-
Page 43: Appendix B Specifications
Power Supply: 4.5” x 2.5” x 1.5” L x W x H Firewall/VPN 3DES 50/48 Mbps Optional: Rackmount Bracket – Concurrent sessions 19” x 8” x 1.75” L x W x H New sessions/second Site-site IPSec VPN tunnels Antivirus throughput RSB-KIT INSTALLATION MANUAL... - Page 44 Storage: – 40°C to 70°C ( – 40°F to 158°F) Anti-spam RBL/SURBL Humidity: 5% ~ 95% typical CERTIFICATIONS ICSA: Firewall, IPSec, SSL, Antivirus, IPS COMPLIANCE FCC Class A, Part 15, UL/CUL, C Tick, CE, VCCI POWER REQUIREMENTS 120/240 VAC 50/60 Hz RSB-KIT INSTALLATION MANUAL...
- Page 45 RJ-45 (10BASE-T): Category 3,4,5 UTP/STP 10% - 90% (non-condensing) RJ-45 (100BASE-TX): Category 5 UTP/STP RJ-45 (1000BASE-T): Category 5,5e or enhanced UTP/STP POWER SUPPLY Fiber: depends on Mini-GBIC types Internal power supply 100-240V/ 50-60Hz universal input NETWORK DATA RATE 10/100/1000Mbps Auto-negotiation RSB-KIT INSTALLATION MANUAL...
-
Page 46: Appendix C - Technical Support
Appendix C – Technical Support Please visit our website for up-to-date support information: Website: www.pakedge.com Email: support@pakedge.com Phone- 1-650-385-8703 CONTACT INFORMATION: Pakedge Device & Software Inc. 1163 Triton Dr. Foster City, CA 94404 RSB-KIT INSTALLATION MANUAL... -
Page 47: Appendix D - Limited Warranty
God. RSB-KIT INSTALLATION MANUAL... - Page 48 This warranty gives you specific legal rights, and you may also have other rights that vary from state to state. 9.4 Effective Warranty Date This warranty begins on the effective date of delivery to the end user. For your convenience, keep the original bill of sale as evidence of the purchase date from your authorized dealer. RSB-KIT INSTALLATION MANUAL...
- Page 49 Return shipping costs will be the responsibility of the owner. For additional information about this warranty, visit our website: For additional information about this warranty, visit our website: Pakedge Device & Software Inc. 1163 Triton Dr. Foster City, CA 94404 Email - support@pakedge.com www.pakedge.com RSB-KIT INSTALLATION MANUAL...
- Page 52 1163 Triton Dr. Foster City, CA 94404 Visit Us At: www.pakedge.com © Pakedge Device & Software Inc. 2010 – All Rights Reserved...
Need help?
Do you have a question about the RSB-KIT and is the answer not in the manual?
Questions and answers